User's Manual

QUICK START PAGE
The e.VOKE Air Sync system includes:
• e.VOKE i5 Air Sync smart box
• Micro USB charging cable
• M2 Air Sync transmitter board with M2 x 3 mm screw
• User’s manual
The e.VOKE system is compatible with the M2 MOSAir board.
POWER ON
To power on your e.VOKE press and hold the center button for 2 seconds.
To power off hold center button for 3 seconds.
CHARGING
Use a standard mini USB cable to charge your e.VOKE from any power supply.
During charging the Power level is indicated by the LED.
SYNC YOUR M2 WITH MOSAIR AND i5 E.VOKE SYSTEM
• Make sure your M2 is Air Sync compatible and the Air Sync module
is installed.
• Make sure the M2 Air Sync is turned on. Go to “PROFILE SETUP” to turn
Air Sync on.
• Return to play mode on M2.
• Turn e.VOKE on.
• M2 and e.VOKE will automatically sync.
If the e.VOKE and M2 MOSAir do not automatically sync, please follow this
process.
• Turn both e.VOKE and M2 MOSAir on.
• Hold the rear #3 button down on e.VOKE to initiate search for M2 device.
• On M2 go to “PROFILE SETUP”, scroll to the Bluetooth screen select
twice to enter setup menu. Initiate i5 pairing search by pressing
joystick on your M2.
• e.VOKE will verbally alert you when M2 is connected. The i5 logo on the
M2 play screen will turn blue when connected to the i5.
During use, the e.VOKE will alert you when your power level becomes low.
INSTALLING e.VOKE IN YOUR M2
WITH MOSAir BOARD
• The Air Sync module is only compatible
with the M2 MOSAir main Board.
• MOSAir boards are identified by their Blue
color and wireless charging system on the
opposite side of the Prism OLED Screen.
FOR OLDER M2 MODELS BEING
UPGRADED
• M2 markers produced in 2016 will need to
be upgraded with the MOSAir main board
to facilitate the e.VOKE system.
• The MOSAir board comes standard with
CFC wireless charging. The power receiver
is connected and mounted to the main
board, on the opposite side of the OLED
screen.
• The wireless CFC component will only fit
under 2017 v2 sticky grips.
• 2017 v2 Sticky grips are identified by the DYE
M2 label located inside the grip on the back
side of the M2 logo jewel (photo A).
• If you have an older model M2 that does not
have MOSAir and a v2 Sticky grip
contact DYE or your local retailer to order.
• The MOSAir and e.VOKE system can be used
without the wireless charging unit installed,
and can therefore be used with v1 2016
sticky grips
M2 MOSAir “AIR SYNC” BOARD
INSTALLATION
• Make sure your M2 is Air Sync compatible
(needs to be upgraded to MOSAir) and the
Air Sync chip module is installed in the M2
MOSAir board.
• Turn on your M2 by pushing and holding the
center of the joystick until your M2 powers
on.
• M2 Air Sync needs to be turned on.
To perform this operation, push the M2
joystick in the up position until you enter
the “PROFILE SELECT SCREEN”
• Select the profile you plan on using
(examlpe P1, P2 etc..) Enter into the profile
by pushing and holding the joysitck in
for one second. This will put you into
“PROFILE SETTINGS”.
• Once you are in profile settings, using your
joystick, toggle to the right two times, to
reach the “BLUETOOTH ICON”.
• Once on the bluetooth screen, push in
the center of the joystick in until “OFF” is
highlighted white.
• Then pull the joystick down once to turn the
bluetooth to the “ON” mode.
• Then press the center of the joystick in to
save this setting and then the word
“SETUP” will appear.
0 - 10% Solid red
11 - 30% Blinks red once every 2 seconds
31% - 90% Blinks blue once every 2 seconds
91% - 99% Blinks green once every 2 seconds
100% Solid green
LED INDEX DURING CHARGING.
OPERATION/STATUS
Power ON / OFF
Bluetooth Unpaired
Bluetooth Paired/ not connected yet
Bluetooth Paired/ connected
Bluetooth connected status checking
> if disconnected
Bluetooth connected status checking
>if re-connected
LED COLOR
Green
Red
Red
Blue
Red
Blue
LED STATUS
Solid for 3 seconds
Rapid blink 4 times per sec.
Blinks once per second
Blinks once every 3 sec.
Blinks once every 3 sec.
Blinks once per second
LED INDEX CHART
Photo A
Photo B
Photo D
Photo C
Photo D
REMOVING THE i5 LENS
TIP: It is recommended that you replace your lens at least once each year.
Factory applied protective coatings on each lens surface will wear off even
with gentle cleaning and regular use abrasion. You should also always
replace your lens after taking a direct paintball hit from within 10 feet.
1 Removing the i5 lens is a quick two step process. Step
1
depress the
top locking tab on the gray frame retention clip and push this tab forward
in the lens locking channel. Step
2
then depress the lower locking tab
on the gray frame retention clip
and push the gray frame retention
clip forward. Perform this on both
sides of the mask. (See figure 1)
You can also use the cyan locking
hook finger grooves to assist you
in sliding the unit forward when
pushing the tabs to clear the release
hook. (See figure 2)
2 Once both gray frame retention
clips are unlocked and in the
forward position, pivot the cyan lens
locking hook 45 degrees inward on
both sides, to fully release the lens.
(See figure 2)
3 To remove the lens, push forward
on the back radius of the right and
left side of the lens, located behind
the Cyan lens-locking hooks. This
will separate the lens from the
Goggle System frame and be easily
removed.
4 Grab the lens from the front by the
top center and nose bridge. Pull the
lens out of the goggle. (See figure 3)
WARNING: Use only your hands
when changing DYE® lenses. Use of
tools is likely to scratch or damage
the lens, void the warranty and risk
injury.
INSTALLING THE i5 LENS
1 The gray frame retention clip should be in the forward position and the
lens locking hooks should be pivoted 45 degrees inward prior to installing
the lens. (See figure 4)
2 Through the front of the mask, slide the lens through the slots on the left
and right side, so that the lens is fully flush with the frame. (See figure 5)
3 Press the lens down against the frame until it is evenly seated against
the goggle frame. Do not use any tools as it is likely to damage the lens,
void the warranty and risk injury.
4 Make sure the nose tab and lens
perimeter is fully seated into the
groove of the goggle frame.
5 The two upper lens tabs should
be properly aligned and inserted into
the two top frame slots as well as the
nose channel tab. The lens should be
flush into the frame.
6 Visually inspect the lens to ensure
there are no gaps between the lens
and frame.
7 Push the Cyan lens locking hooks
outwards, against the mask and
lens, then pull the lens locking tab
rearward. This will ensure the lens
locking hooks engage the lens to
lock it into place. Visually confirm
the e.VOKE and cyan locking hooks
have engaged the lens. (See figure 6)
8 Starting with the right side locking
clip, pull the top of the cyan clip
rearward, until you hear it click
into the locked position. Repeat
this process for the bottom clip
until you here the tab click into the
locked position. Duplicate this same
process for the left side locking clip.
(see figure 8).
Figure 3
Figure 2
Figure 1
1
2
Figure 6
Figure 5
Figure 4 Figure 7
Figure 8CORRECT
Figure 9
WRONG
9 Visually inspect the top and bottom locking tabs on the frame retention
clip to confirm they have locked into place. The tabs should be fully
rearward in the locking channel. (See figure 7)
10 Visually inspect the back side of the Cyan lens locking hook. Confirm
the locking hooks have extended through the holes in the lens and have
securely locked the lens into place. The Cyan retention clip will sit flush
against the lens, if it is engaged properly (see figure 8).
If the lens is not properly secured (see figure 9) you will see the lens hook
exposed. Do not use your i5 goggle unlesss you are sure your lens is
properly installed.
CONFIRMING PROPER
INSTALLATION OF THE i5 LENS
1 Visually inspect the back side
of the Cyan lens locking hook and
e.VOKE locking hook. Confirm the
locking hooks have extended through
the holes in the lens and has securely
locked the lens in place.
(photo D)
The Cyan retention clip and e.VOKE
will sit flush against the lens, if it is
engaged properly (See Figure 8).
2 If the lens is not properly secured
(See Figure 9) you will see the lens
hook exposed. Do not use your I5
goggle, unless you are 100% certain
that your lens is securely in place
and properly secured. Repeat the
locking process if necessary, to
securely lock the lens in place. If you
should have any difficulty or are not
sure if you have performed the lens
replacement correctly, please call
Dye customer service for help.
e.VOKE INSTALLATION
1 Replace the left Cyan lens locking hook with the e.VOKE
Air Sync smart box.
2 Make sure the buttons and strap logos are facing up.
3 Follow the above steps in reverse to install the frame
retention clip and strap to e.VOKE.
4 Once the e.VOKE is installed it will function as the lens
locking hook, and secure the lens in place.
INSTALL e.VOKE INTO i5 GOGGLE
The e.VOKE is designed to fit on the left side of the i5 (photo D).
REMOVE GSR SYSTEM
1 With the lens removed, pull the left side mask retaining clip rearward,
depress top and bottom locking tabs as you pull, this will allow you to sep-
arate the retaining clip from the mask.
(See Figure 10)
2 Once the clip is separated from
the mask, on the left retention clip
press the steel pin up from the bot-
tom to remove.
(See Figure 11)
3 Unscrew the ear pad retaining
screw. (See Figure 12)
Figure 11
Figure 10 Figure 12
• Push the center of the joystick in again for one second to enable your M2
to prompt you to “SYNC” to the I5 e.VOKE unit.
• Push and hold the center of the joystick in again for one second to
“SELECT TO
SYNC”
• This will trigger your M2 to search for the e.VOKE device blutooth signal
and attempt connection.
• You will need to have the M2 and e.VOKE within one foot distance of
eachother to connect.
• Turn on your e.VOKE by pushing and holding the e.VOKE center #2 button,
until it powers on. You will see a green power on light on the e.VOKE unit.
• Then push and hold the e.VOKE rear #3 button and you will hear an
auditory message “SEARCHING FOR DEVICE” from your e.VOKE unit.
• Upon successful connection, you will hear an auditory message from
your e.VOKE stating “PAIRED”.
• Your M2 and e.VOKE are now successfully connected.
IF YOUR e.VOKE DOES NOT CONNECT,
REPEAT THE SYNC PROCESS.
• While on the “CONNECTION FAILED” screen, press the center of the M2
joystick for 1 second “SELECT TO RETRY”, this will allow your M2 to
search for your e.VOKE.
• With your e.VOKE on, press and hold the rear #3 button to allow your
e.VOKE device to search for your M2.
• Upon successful connection, you will hear an auditory message from
your e.VOKE stating “PAIRED”.