Installation Guide

ManualsBrandsDyconn Faucet ManualsBathroomCatella Plus 48-in Silver Rectangular Frameless Lighted LED Bathroom Mirror

Product Features:

Frameless backlit Mirror

Extra thick frosted LED light

Can be vertical or horizontal hanging

Touch switches on & oﬀ

Touch switch dim function

Anti-fog pad

LED Backlit Mirror

Sizes: 48” W x 36“ H (Horizontal)

60” W x 35”H (Horizontal)

72” W x 38”H (Horizontal)

Model: Catella-Plus M10AT

Thoroughly read all instructions before installing the enclosed product.

Read and take note of all safety, care, and maintenance information.

E491008

Summary of content (10 pages)

PAGE 1
Product Features: Frameless backlit Mirror Extra thick frosted LED light Can be vertical or horizontal hanging Touch switches on & oﬀ Touch switch dim function Anti-fog pad LED Backlit Mirror Sizes: 48” W x 36“ H (Horizontal) 60” W x 35”H (Horizontal) 72” W x 38”H (Horizontal) Model: Catella-Plus M10AT Thoroughly read all instructions before installing the enclosed product. Read and take note of all safety, care, and maintenance information.
PAGE 2
PAGE 3
Warning: Please read!! electrician. 2. During installation please make sure the circuit breaker or the with a live line on. 3. It is recommended to have at least two people available to install the mirror. Remember to wear proper protective gear during installation. All mirror glass is non-tempered glass and can result in sharp shards if the glass is shattered. wall. Using the proper anchor and screws for securing the unit to the wall is crucial. Screwing to the stud is recommended.
PAGE 4
Product Description & Information Product Features: Package Content: • Frameless backlit Mirror • Extra thick frosted LED light • Horizontal installation • Touch switch on & oﬀ • Touch switch dim function • Anti-fog pad • LED backlit mirror • Screws • Studs Metal Back Frame 6mm Silver Mirror 2835 LED Strip 4000k-36W-4210LM 2835 LED Strip 4000k-65W-7605LM 120V-LED driver x 2 Touch Switch Touch Switch Mounting Screws x 4 Acrylic Diffuser Frame Warning: Always switch oﬀ the electrical supply at the
PAGE 5
Step 1 1. Mark the desired position on the wall. Drill the holes and secure with the wall studs. This mirror can only be hung horizontally. 1.2. Make sure the screw is secured. Step 2 2. Do not open mirror. Make sure the circuit breaker for the power source of the mirror is oﬀ. Then connect the neutral (White), hot (black), and ground (copper wire or Green) wire between the mirror and the junction box. Live Ground Neutral Electric wire color code: Black: Live Green: Ground White: Neutral Wall Step 3 3.
PAGE 6
LED Mirror Power Source FAQ Internal Power Flow Diagram Scenario 1 (Direct Wired) This is the most common way to connect the mirror. The LED light & anti fog pad are both controlled by the built-in touch switch on the mirror. *The LED light is dimmable. 110VAC Input Power Source: Constant 110AC power 110VAC -12VDC LED driver Output Anti-fog pad Output Dimmer Switch 12V LED Light Scenario 2 (Wall Switch) By doing so, the mirror is now bridged to the wall switch.
PAGE 7
Introducing Tri-Color Mirrors and Additional Features In the near future, Dyconn Faucet will be upgrading our mirror products to include tri-color options and additional features.
PAGE 8
Dyconn Faucet LED Small Mirror Frequently Asked Questions & Troubleshooting Guide 1. Can I connect to a dimmer on the wall to dim the mirror (ELV or non ELV dimmer) Answer: Unfortunately, no, the mirror cannot be connected to an ELV dimmer or traditional non-ELV dimmer switch. All Dyconn Faucet mirrors contain low voltage LEDs and the power supply will not work properly if the source AC is altered through a wall AC dimmer. 2. Can I connect to a non-dimmer wall switch? Answer: Yes.
PAGE 9
Wall Switch Bypass Instructions 3. 2. Numbers will correspond to following tags attached to the wires 1. + - 12 2. LED 3. E491008 Use the following steps to wire mirror to an electrical wall switch and bypass the touch sensor: 1. Disconnect all connections from the touch sensor (#1-3). 2. Connect the LED Power Supply directly to the 12V DC LED Connector (#1 and #2 circled in red).
PAGE 10
Manufacturer Limited Warranty E491008 All Dyconn Faucet products are manufactured and tested with the highest quality standards and rigorous quality control process. This warranty is limited to the non-commercial use of Dyconn Faucet products purchased and installed in the United States and Canada.