Installation Sheet

ManualsBrandsDXV ManualsBathroom FaucetsPercy Sc Vessel Stem Hdl 1.2 GPM

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.

SAVE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing

supply stores. It is essential that the tools and materials be on hand before work is begun.

M965708 Rev. 1.0 (5/17)

Pixie Handle Monoblock - Model D3510510C

Loop Handle Monoblock - Model D3510512C

Pixie Handle Vessel - Model D3510515C

Loop Handle Vessel - Model D3510517C

Percy

Single Control Monoblock

and Vessel Faucet

ROUGHING-IN DIMENSIONS:

• For reference

Adjustable Wrench Flat Blade Screwdriver Channel Locks

NOTE: MOUNTING HOLE 1-1/4" (32 mm) D.

MOUNTING

SURFACE

20"

(508mm)

FLEXIBLE

HOSES

9-9/16"

(243 mm)

6-3/4"

(171 mm)

8-13/16"

(223 mm)

3-5/8"

(92 mm)

1-1/2"

(38 mm) MAX.

2-1/4"

(57 mm)

1-1/4" OD

(32 mm OD)

12-1/2"

(318 mm)

4-1/2"

(114 mm)

2-7/16"

(63 mm) D.

LOOP

HANDLE

PIXIE

HANDLE

14-7/8"

(378 mm)

14-1/8"

(359 mm)

6-3/4"

(171 mm)

8-15/16"

(227 mm)

2-1/4"

(57 mm)

4-1/2"

(114 mm)

SUPPLY CONNECTIONS ARE 3/8" COMPRESSION

(51 mm) MAX.

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your

installation proceeds smoothly, please read these

instructions carefully before you begin.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS ® Percy Single Control Monoblock and Vessel Faucet Pixie Handle Monoblock - Model D3510510C Loop Handle Monoblock - Model D3510512C Pixie Handle Vessel - Model D3510515C Loop Handle Vessel - Model D3510517C Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing supply stores. It is essential that the tools and materials be on hand before work is begun.
PAGE 2
1 INSTALL FAUCET CAUTION Turn off hot and cold water supplies before beginning. • Seat O-RING SEAL (1) into under side of FAUCET BASE (2). • Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN CABLE ASSEMBLY (8) through the mounting hole of lavatory or mounting surface. Fig. A. • From below, push GASKET (7) and RETAINING WASHER (5) onto MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6), pulling faucet to front of sink, so SUPPLIES (3) rests against mounting hole.
PAGE 3
2 POP-UP DRAIN Fig. A. Fig. B. • Remove CLEAR PLASTIC COVER (1). Fig. A. 1 • Remove FOAM SPACER (2) from under DRAIN POP-UP (3). Fig. A. 3 • Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. DRAIN BODY 2 3 REMOVE MOUNTING WASHERS 4 Fig. A. AND LOCKNUT Fig. B. REAR OF SINK • Thread LOCKNUT (1) counter-clockwise and remove from drain body. Remove PLASTIC WASHER (2) and pull off RUBBER CONE WASHER (3) Fig. A. 3 • Drop DRAIN BODY (4) through sink drain hole.
PAGE 4
7 ATTACH CABLE CONNECTOR Fig. A. Fig. B. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 • Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4" (32 mm) O.D. Fig. B. 2 1-1/4” O.D. 8 CHECK OPERATION OF POP-UP • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.
PAGE 5
10 TEST INSTALLED FITTING • With HANDLE (1) in OFF position, remove AERATOR (3). Turn on WATER SUPPLIES (2) and check all connections for leaks. • Operate HANDLE (1) to flush water lines thoroughly. Replace AERATOR (3). CHECK DRAIN CONNECTIONS • Operate POP-UP KNOB (4) and fill lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains water in sink. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
PAGE 6
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 7
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). LOCKED MODE: Fig. G. • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink.
PAGE 8
® Percy Single Lever Monoblock and Vessel Faucets MODEL NUMBERS Monoblock Pixie Handle D3510510C Loop Handle D3510512C Vessel M964631-YYY0A LOOP HANDLE KIT (D3510512C, D3510517C) Pixie Handle D3510515C Loop Handle D3510517C Replace the “YYY” with appropriate finish code M964633-0070A CARTRIDGE KIT M964634-0070A MANIFOLD SEAL KIT M964635-YYY0A LIFT KNOB & ROD (MONOBLOCK) POLISHED CHROME 100 BRUSHED NICKEL 144 M964632-YYY0A PIXIE HANDLE KIT (D3510510C, D3510515C) Monoblock Faucet M964637-YY