Installation Sheet

ManualsBrandsDXV ManualsBathroom FaucetsREM 1.2 GPM Widespread Bathroom Faucet with Pop-Up Drain Assembly

- 1 -

INSTALLATION INSTRUCTIONS

Product names listed herein are trademarks of AS America, Inc.

SAVE FOR FUTURE USE

RECOMMENDED TOOLS AND MATERIALS

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,

supply stores. It is essential that the tools and materials be on hand before work is begun.

M965702 Rev. 1.1 (5/17)

Model D3510080C

Rem

Widespread Lavatory Faucets

Plumbers' Putty or Caulking

Phillips Screwdriver

Channel LocksTubing Cutter Flat Blade Screwdriver Adjustable Wrench

Basin Wrench

ROUGHING-IN DIMENSIONS:

• For reference

6" to 12"

(152 to 305 mm)

NOTE: MOUNTING HOLES ARE 1-3/8" DIA. (35 mm)

MOUNTING

SURFACE

7-5/8"

(194 mm)

4-1/2"

(114 mm)

(75 mm)

2" DIA.

(51 mm)

2-3/8"

(60 mm)

3/4"

(19 mm)

1-1/4 O.D.

(32 mm)

7/8 DIA.

(22 mm)

1-1/2" MAX.

(38 mm)

1-3/8" MAX.

(35 mm)

MAX 2"

(51 mm)

10" MAX.

(254 mm)

CONNECTIONS:

• 1/2" IPS FLEXIBLE SUPPLIES

• 3/8" O.D. BULL-NOSE RISERS

In the United States:

DXV

One Centennial Avenue

Piscataway, New Jersey 08855

Attention: Director of Customer Care

For residents of the United States, warranty

information may also be obtained by calling

the following toll free number: (800) 227-2734

www.DXV.com

In Canada:

DXV

5900 Avebury Road

Mississauga, Ontario

L5R 3M3

Canada

Toll Free: 1-800-387-0369

Local: 905-306-1093

Fax: 1-800-395-1498

www.DXV.ca

In Mexico:

DXV

Via Morelos 330

Col. Santa Clara Coatitla

Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200

www.DXV.mx

Thank you for selecting DXV. To ensure that your

installation proceeds smoothly, please read these

instructions carefully before you begin.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Rem® Widespread Lavatory Faucets Model D3510080C Thank you for selecting DXV. To ensure that your installation proceeds smoothly, please read these instructions carefully before you begin. RECOMMENDED TOOLS AND MATERIALS Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing, supply stores. It is essential that the tools and materials be on hand before work is begun.
PAGE 2
1 SPOUT ASSEMBLY CAUTION 2 TEE ASSEMBLY Turn off hot and cold water supplies before beginning. • Thread TEE BODY (1) COUPLING NUT (2) to SPOUT SHANK (3). Tighten with wrenches. • Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure SEAL WASHER (3) is properly seated in SPOUT BASE (4) groove. • Assemble RUBBER WASHER (5), BRASS WASHER (6) and LOCKNUT (7) onto SPOUT SHANK (8) from under side of sink.
PAGE 3
4 INSTALL POP-UP DRAIN Fig. A. Fig. B. • Remove CLEAR PLASTIC COVER (1). • Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). 1 DRAIN BODY 3 • Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 5 REMOVE FLANGE 4 Fig. A. Fig. B. • Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. 2 • Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.
PAGE 4
9 ATTACH CABLE CONNECTOR Fig. A. Fig. B. • Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. 1 Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4" O.D. Fig. B. 2 1-1/4” O.D. (32 mm) 10 CHECK OPERATION OF POP-UP 1 • Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.
PAGE 5
12 CONNECT DRAIN • Connect 1-1/4" O.D. tailpiece on POP-UP DRAIN to waste outlet. 1-1/4” O.D. TAILPIECE WASTE OUTLET 13 TEST INSTALLED FITTING • With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. • Remove AERATOR (3). First loosen aerator set screw with HEX WRENCH (4) supplied. Pull out AERATOR (3) with AERATOR KEY (5). 3 4 5 1 • Operate HANDLE (1) to flush water lines thoroughly. 6 • Replace AERATOR (3) and tighten set screw.
PAGE 6
Speed Connect® Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
PAGE 7
STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). LOCKED MODE: Fig. G. • Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G. • To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink.
PAGE 8
Rem® Widespread Lavatory Faucets MODEL NUMBERS D3510080C Replace the “YYY” with appropriate finish code POLISHED CHROME 100 BRUSHED NICKEL 144 H960848.XXX HANDLE ASSEMBLY H960873.191 HANDLE ADAPTER H960849.XXX ROSETTE A962294.191 AERATOR ASSEMBLY H960279.191 MOUNTING KIT H960295.191 SPOUT MTG. KIT M964535-YYY0A LIFT KNOB ASSEMBLY H961260.191 MOUNTING KIT H960136.191 1/2" CARTRIDGE (CLOCKWISE ON) M953006-0070A TEE AND HOSE ASSEMBLY M952430-0070A SPEED CONNECT® ASSEMBLY H960742.