Installation Sheet

- 1 -
SAVE FOR FUTURE USE
7302038-100 Rev. E (8/15)
7302038-100 Rev. E (8/15)
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
Rectangular - model #D20080
Square - model #D20085
Round - model #D20090
Thank you for selecting DXV by American Standard. To ensure this product is installed properly, please read these instructions carefully
before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
!
INSTALLATION INSTRUCTIONS
Pop
™
Above Counter Sinks
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2015
Level
Square
NOTE: More specialized tools may be necessary to install this sink to countertop materials other than wood or wood composites.
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
RECOMMENDED TOOLS AND MATERIALS
PRODUCT SPECIFICATIONS
Adjustable WrenchChannel Locks
Regular Screwdriver
Phillips Screwdriver
10'
Saber SawPipe Wrench
Tubing Cutter
Tape Measure
Electric
Drill
Hacksaw
Plumbers' Putty or
Caulking
RECTANGLE - D20080 SQUARE- D20085 ROUND - D20090
NOTES: * DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE SUGGESTED.
INSTALLATION PROCEDURES
INSTALLING BASIN
Typical installation includes installation of faucet, connection of exible water supply lines, attachment of basin to countertop, sizing and
installation of drain to house water system.
STEP 1.
STEP 2.
STEP 3.
STEP 4.
STEP 5.
STEP 6.
STEP 7.
Using carpenters square ensure that the countertop is level. Next, carefully position the lavatory in the desired location for the basin.
Ensure you have provided proper clearance under the countertop for the faucet, supply lines, drain assembly and the structural parts of
the cabinet. Mark desired drain and faucet location on countertop with pencil. Please refer to faucet installation instructions to verify
desired faucet rough-in areas.
Drill a 4" (102 mm) hole at drain location. Drill a hole at faucet mount location using faucet installation instructions for exact positioning.
Position lavatory in place, centering it above the drain hole. Place clear silicone bead around perimeter of lav where lav meets counter.
Pre-assemble P-trap drain connections in accordance with manufacturer’s instructions. Check that pop-up drain opens and closes
properly when drain control is operated.
Connect supply lines to shutoff valves and securely tighten nuts.
Install faucet and drain in accordance with manufacturer’s instructions. Hand tighten drain and add one quarter turn to allow the sink to
expand and contract with changing water and room temperatures. If drain leaks, add another quarter turn. Repeat this process until leak
stops. Do not over tighten to prevent stress cracks. Turn on water supply valves and water-test installation.
Place Ceramic drain cover on top of metal pop-up drain; ensure DXV logo is facing to the front.
In the United States:
DXV by American Standard
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV by American Standard
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV by American Standard
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
PART
7381350-200.XXX0A — Ceramic Drain Cover
4"
(102 mm)
3-13/16"
(97 mm)
COUNTERTOP
(BY OTHERS)
5"
(127 mm)
28"
(711 mm)
6-9/16"
(167 mm)
1-1/4" (32 mm) O.D.
WASTE
1-1/4" (32 mm) O.D.
TAILPIECE
20"
(508 mm)
18"
(457 mm)
FINISHED
FLOOR
SUPPLIES
AS REQ’D
6"
(152 mm)
*
CUTOUT AREA
4"(102 mm)
1-3/4" (45 mm)
DIA. STD.
DRAIN OUTLET
FINISHED WALL
4" (102 mm) MIN.
IF REAR AREA
FAUCET IS USED
11"
(278 mm)
22"
(557 mm)
20-7/8"
(531 mm)
7-1/2"
(190 mm)
15"
(380 mm)
13-15/16"
(354 mm)
COUNTERTOP
(BY OTHERS)
CEMENT
BOND
4"
(102mm)
5"
(127mm)
28"
(711 mm)
1-1/4" (32 mm) O.D.
WASTE
1-1/4" (32 mm) O.D.
TAILPIECE
20"
(508 mm)
18"
(457 mm)
FINISHED
FLOOR
SUPPLIES
AS REQ’D
6"
(152 mm)
*
6-9/16"
(167 mm)
1-3/4" (45 mm)
DIA. STD.
DRAIN OUTLET
FINISHED WALL
CUTOUT AREA
4" (102 mm)
4" (102 mm) MIN.
IF REAR AREA
FAUCET IS USED
7-1/2"
(190 mm)
7-1/2"
(190 mm)
15"
(380 mm)
15"
(380 mm)
1-1/4" (32 mm) O.D.
WASTE
1-1/4" (32 mm) O.D.
TAILPIECE
COUNTERTOP
(BY OTHERS)
CEMENT
BOND
4"
(102 mm)
13-5/8"
(346 mm)
5"
(127 mm)
28"
(711 mm)
20"
(508 mm)
18"
(457 mm)
FINISHED
FLOOR
SUPPLIES
AS REQ’D
6"
(152 mm)
*
3-13/16"
(97 mm)
6-9/16"
(167 mm)
1-3/4" (45 mm)
DIA. STD.
DRAIN OUTLET
FINISHED WALL
CUTOUT AREA
4" (102 mm)
4" (102 mm) MIN.
IF REAR AREA
FAUCET IS USED
7-1/2"
(190 mm)
7-1/2"
(190 mm)
15"
(380 mm)
15"
(380 mm)
13-15/16"
(354 mm)
3-13/16"
(97 mm)