DWC-MC355T Micro Dome Camera User Manual ABOUT MANUAL Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for future reference.
PRECAUTIONS Do not open or modify. Do not open the case except during maintenence and installation, for it may be dangerous and can cause damages. Do not put objects into the unit. Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages. Be careful when handling the unit. To prevent damages, do not drop the camera or subject it to shock or vibration. Do not install near electric or magnetic fields. Protect from humidity and dust.
TROUBLESHOOTING Before sending your camera for repair, check the following or contact our technical specialist. No VIDEO Check the coaxial cable and make sure it is connected securely. Check the lens’ iris adjustment at the menu setup of the camera. Check the power supply and make sure the camera has the proper voltage and current. Out-of-Focus VIDEO Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean. Check the lens manual focal and zoom adjustment.
DIMENSIONS IN MILLIMETERS* 4
INSTALLATION* 1. Remove the 1 STOP SCREW(B) on UPPER CASE(C), using the L-WRENCH(A). 2. Separate UPPER CASE(C) from BOTTOM CASE(E). 3. Make the 4 mounting screw holes on the ceiling/wall. The holes of BOTTOM CASE(E) can help locate the correct hole locations. 4. Put POWER CABLE(F) AND VIDEO CABLE(G) into the ceiling/wall. 5. Fix the BOTTOM CASE(E) onto the ceiling/wall, using the SCREWS(D) 6. Camera adjustment and setting. (Referance - “CAMERA SETTING”) 7. Connect UPPER CASE(C) and BOTTOM CASE(E). 8.
CONNECTIONS* 12VDC CAUTION : Check for polarity when using a DC 12V.
LENS ADJUSTMENTS* Adjust the pan (360º) and tilt (70º) position.
CAMERA SETTINGS* Camera Position Adjustment : (1) Loosen the SCREW(B) on the UPPER CASE(C), using L-WRENCH(A). (2) Separate BOTTOM CASE(E) from UPPER CASE(C) by twisting UPPER CASE(C) to the right. (3) Separate CLEAR DOME(D) from BOTTOM CASE(E). (4) Fix the camera gimbal located in the BOTTOM CASE(E). (5) Assemble CLEAR DOME(D) and UPPER CASE(C) with BOTTOM CASE(E). (6) Tighten SCREW(B) onto UPPER CASE(C), using L-WRENCH(A).
WARRANTY INFORMATION* Digital Watchdog (referred to as “the Warrantor”) warrants Camera Series against defects in materials or workmanship as follows. LABOR : For the initial five (5) years and one (1) year on LED from the date of original purchase, if the camera is determined to be defective, the Warrantor will repair or replace the unit, with new or refurbished product at its option, at no charge.
LIMITS AND EXCLUSIONS* There are no express warranties except as listed above. The Warrantor will not be liable for incidental or consequential damages (including without limitation and damage to recording media) resulting from the use of these products, or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.
SPECIFICATIONS* Specifications Model Camera TYPE Image Scanning Min. Scene Illumination WDR DIP Switch Lens Resolution Video Output S/N Ratio Environmental Conditions Power Physical Specification Certifications MC355T Color Mount Device Pixels-Total Pixels-Effective System Horizontal Frequency Internal Mode Vertical Frequency Internal Mode F1.2 Wide Dynmic Range NTSC/PAL Length Horizontal VBS 1.
5436 W Crenshaw St. Tampa, FL 33634 Tel : 866-446-3595 / 813-888-9555 Fax : 813-888-9262 www.Digital-Watchdog.com technicalsupport@dwcc.
