4 CHANNEL DVR User Manual SRD-440
4 Channel DVR User Manual Copyright ©2011 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
overview IMPORTANT SAFETY INSTRUCTIONS OVERVIEW Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth.
overview BEFORE START This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection to other equipment, menu setup, etc. You have to keep in mind the following notices : • SAMSUNG retains the copyright on this manual. • This manual cannot be copied without SAMSUNG’s prior written approval. • We are not liable for any or all losses to the product incurred by your use of non-standard product or violation of instructions mentioned in this manual.
CONTENTS OVERVIEW 3 12 LIVE 17 USING THE DVR 28 Important Safety Instructions Before Start Features Part Names and Functions (Front) Part Names and Functions (Rear) Remote Control 12 12 13 13 13 14 14 15 Installation Checking the installation environment Connecting the Video, Audio, and Monitor Connecting the USB Connecting POS Device Connecting the Alarm Input/Output Connecting the RS-485 Device Connecting the Network 17 19 23 25 25 26 26 26 Getting Started Live Screen Configuration Live Mode Spot
overview SEARCH & PLAY 62 WEB VIEWER 67 BACKUP VIEWER 62 65 Search Playback 67 68 69 75 79 90 91 Introducing Web Viewer Connecting Web Viewer Using Live Viewer Using Search Viewer Viewer Setup About Mobile Viewer 92 SEC Backup Viewer 94 96 97 100 103 Product Specification Product Overview Default Setting Troubleshooting Open Source License Report on the Product 92 APPENDIX 94 6_ overview
FEATURES The DVR employs H.264 video encoding for 4 channel inputs and audio encoding for 1 channel while simultaneously supports hard disc recording and playback. These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video and audio data.
overview Standards Approvals M This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PART NAMES AND FUNCTIONS (FRONT) DIGITAL VIDEO RECORDER SRD-440 POWER REC OVERVIEW bc Part Names Functions USB Port Connects the USB devices. b Remote Control Receiver Input the remote control signal. c LED Indicator Power LED : Displays the power ON/OFF status. REC : Lights on when recording is in progress.
overview PART NAMES AND FUNCTIONS (REAR) b c AUDIO IN 1 NETWORK 2 ALARM OUT 1 COM VGA 1 ALARM IN 2 3 4 G G DC 12 V RS-485 + CONSOLE 3 4 VIDEO IN VIDEO OUT (SPOT) AUDIO OUT Part Names b c M USB SERIAL Functions VIDEO IN Input port for the composite video signal. VIDEO OUT (SPOT) BNC type of output port for the composite video signal. AUDIO IN Input ports (RCA jack) for the audio signal. VGA Output port for VGA video signal.
REMOTE CONTROL SEARCH Displays the search menu. BACKUP Displays the Backup Menu. MODE Changes the screen mode. POWER DVR Activates the DVR function. Displays the Exit pop up screen. ID Skip Backward (by unit time), Slow Rewind, Slow Forward, Skip Forward (by unit time) Sets the ID of the system. Select 2 digits from 0 ~ 9 while pressing the ID Key. Move Frame While paused, moves to the previous/next frame. FR, STOP, PLAY/PAUSE, FF T/W Zooms in or out. PTZ Displays or ends PTZ. SCROLL ,.
connecting with other device INSTALLATION Please take note of the followings before using this product. • • • • • • • • Do not use the product outdoor. Do not spill water or liquid in the connection part of the product. Do not impose the system to excessive shock or force. Do not pull out the power plug forcefully. Do not disassemble the product on your own. Do not exceed the rated input/output range. Use a certified power cord only. For the product with an input ground, use a grounded power plug.
CONNECTING THE VIDEO, AUDIO, AND MONITOR NETWORK 2 ALARM OUT 1 COM VGA 1 ALARM IN 2 3 4 G G DC 12 V RS-485 + CONSOLE 3 4 VIDEO IN M VIDEO OUT (SPOT) AUDIO OUT SERIAL USB Only one mouse port is available. CONNECTING THE USB 1. By factory default, a USB port is provided for external connection. 2. You can connect a USB HDD, USB memory or mouse to the USB port. 3. If a USB HDD is connected to the system, recognition and settings are available in “Menu > Setting the Device > Storage Device”.
connecting with other device CONNECTING THE ALARM INPUT/OUTPUT Connecting the alarm input signal IN NETWORK ALARM OUT 1 COM Connection port for the alarm input signal. Connect one strand of the sensor signal line to one of 4 strands of the alarm input port, and connect the other strand to the [G] port. VGA 1 ALARM IN 2 3 4 G DC 12 V RS-485 + G CONSOLE OUT USB SERIAL ALARM OUT 1 COM Connecting the alarm output signal Connection port for the alarm output signal.
CONNECTING THE NETWORK Connecting to Network through Ethernet (10/100BaseT) AUDIO IN 1 NETWORK 2 ALARM OUT 1 COM VGA ALARM IN 2 3 4 G 1 G DC 12 V RS-485 + CONSOLE 3 4 VIDEO OUT (SPOT) AUDIO OUT USB SERIAL RJ-45 Ethernet Cable (Direct Cable) NETWORK Back Bone Hub/Switcher Windows Network Viewer Hub/Switcher Connecting to the Network using the router AUDIO IN 1 NETWORK 2 ALARM OUT 1 COM VGA ALARM IN 1 2 3 4 G G DC 12 V RS-485 + CONSOLE 3 4 VIDEO IN VIDEO OUT (SPOT) AUDIO OUT US
connecting with other device Connecting to Network through ADSL AUDIO IN 1 NETWORK 2 ALARM OUT 1 COM VGA ALARM IN 1 2 3 4 G G DC 12 V RS-485 + CONSOLE 3 4 VIDEO IN VIDEO OUT (SPOT) AUDIO OUT SERIAL USB RJ-45 Ethernet Cable (Direct Cable) NETWORK Phone(ADSL) Line Hub/Switcher 16_ connecting with other device ADSL MODEM Windows Network Viewer
live GETTING STARTED Starting the system M LIVE 1. Connect the power cable of the DVR to the wall outlet. It takes about 10 seconds to display the start screen after booting. 2. You will see the initialization screen. The initialization process will last about 1 minute. If a new HDD is installed, the initialization process may take longer. 3. The live screen appears with a beep.
live Login To access a DVR or restricted menu, you should have logged in to the DVR. 1. In live mode, right-click any area of the screen. You will see the context sensitive menu as in the right figure. Scene Mode 2011-01-01 01:10:25 Spot Out Audio Off Freeze Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Login 2. Click . The login dialog appears. You can also see the login dialog to access a desired menu by pressing the [MENU] button on the remote control.
LIVE SCREEN CONFIGURATION Icons on the Live Screen You can check the status or operation of the DVR with the icons on the live screen. 2011-01-01 00:00:01 LIVE CAM 01 Name b Description Current Date, Time Displays the current time and date. Login Information When you are logged in, the “LOG ON” icon will be displayed. Displayed if the zoom function is activated. Displayed if you press the Pause button.
live Error Information • If the internal HDD is not connected, the “NO HDD”( ) message will appear; if there occurs a problem, ) message in the top left corner. In this case, make sure you contact the you will see the “HDD FAIL”( service center for assistance as this may cause a failure of recording, playback or backup. M If you see the No HDD, HDD FAIL icons on the screen, contact the service center for more details.
Menu b c m Scene Mode Refer to “Live Mode”. (Page 23) Spot Out Refer to “Spot Out”. (Page 25) Audio On/Off Refer to “Audio ON/OFF”. (Page 26) Freeze Refer to “Freeze”. (Page 26) Stop Alarm Stop the alarm output, deactivate the event icon and release the auto sequencing. Refer to “Event Monitoring”. (Page 26) Record/Stop Starts/stops the standard recording. Play Refer to “Search & Play > Play”. (Page 65) Search Refer to “Search & Play > Search”.
live View the Launcher Menu The Launcher menu appears on the bottom of the live screen. 1. In Live mode, right-click to display the context menu and select . 2011-01-01 01:10:25 2. Move the cursor to the bottom and click a desired item in the Launcher menu. M If no input is entered for 10 seconds, the menu will disappear. The Launcher menu can be accessed only by using the mouse.
LIVE MODE Displays 4 live video images in 3 different modes. Switching the screen mode CH1 CH2 CH3 CH4 CH2 CH1 CH1 4-split mode PIP Auto Sequence Switching the screen automatically With SRD-440 you can display 4 live single screens in sequence. 4 CH1 CH1 CH1 CH1 Single mode M 1 In Single mode, If you have set in “Setting the Device > Camera”, Auto Sequence will be conducted at the set interval.
live Channel Setting You can display the channel in a desired area of a split screen. 1. Click a camera name to display a channel list where you can select a different channel. 2. Select a desired channel and click it. The current channel will be switched to the selected one. Use the cursor to select a channel to move, and drag and drop it to a desired channel; this can also change the channel position.
SPOT OUT The Spot Out monitoring is independent of the Live mode, which monitors a specific channel through the Spot Out port. Selecting a Spot Out mode If an event occurs such as sensor, motion or alarm from the Spot Out port in connection with a monitor, you can select a output screen mode. Scene Mode Spot Out Audio Off 2. Click . Supports the Spot output in Single screen with Auto Sequence mode.
live AUDIO ON/OFF You can turn the sound on/off the CH1 in Live mode. AUDIO ON/OFF in Single mode Click the audio icon ( M ) on the screen, or press the [AUDIO] button on the remote control to turn it on/off. Only the channel where
Ex : If you set to 5 seconds, and the second event occurs in CH 2 within the set time after the first event occurred in CH 1. Event occurrence 4 seconds 9 seconds CH1 LIVE Stop alarm CH2 CH1 M Press the [ALARM] button to reset the alarm settings and to release the event mode. If an alarm activates in the condition you have set the event record, and pre/post alarm times, the event record will be performed.
using the DVR You can setup the system properties, devices, and options for recording, event, backup and network. SYSTEM SETUP You can setup Date/Time/Language, Permission, System Properties and Log. Date/Time/Language You can check and setup the current Date/Time and time related properties, as well as the language used for the interface on the screen. Setting the Date/Time/Language Set the Date/Time/Language Using the mouse may help make setup easier. 1. Press the [MENU] button on the remote control.
- Time Server : Enter an IP or URL address of the time Date/Time/Language server. Date/Time/Language Holiday - Last Sync Time : Displays the most recent Time Synchronization Setup synchronization time from the selected time server. - Activate as Server : Set to
using the DVR Permission Management You can set permissions of each user over the DVR's specific function and settings. Setting the Administrator You can set and change Administrator’s ID and password. The administrator can use and set all menu items and functions. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. Permission Management Admin Group ID 2. Select .
Setting the Group You can create user groups and setup permissions for those user groups. You can register a user for each group in . Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. Group Admin User Group Add Setup Delete Rename Group Authority Live View Setup Search Setup Backup Setup USING THE DVR 2. Select .
using the DVR To restrict the user permissions If the admin restricts all permissions of an added group, the users belonging to that group can access only the default minimum menus and can change the user’s own password only. 1. Start the DVR. If all permissions are restricted, only the Login dialog should appear. 2. Log in with a registered user ID. Login ID abc Password OK 3. Right-click any area on the screen. If all permissions are restricted, only the accessible context menus should appear.
Setting the User Users can be added only if a group was created in menu. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 3. Use direction buttons ( ◄ ►) to select from the window. A window for “Add User” appears. You can configure the Network Viewer settings including name, ID, viewer, Select Group and password. Result of the user setup appears in the window.
using the DVR • Manual Input of ID : Prompts you to enter the user ID manually for the login process. - Checked ( ) : Encloses the registered user IDs with the [] symbols. Use the virtual keyboard to enter the user ID. Login ID ***** Password 4. When the permission setup is done, press . OK Cancel System Management You can check the system version, update to a newer version, as well as data backup and initialization.
• Updating the Software 1. Connect a device storing the software to be updated. (It may take about 10 seconds to recognize the device.) Upgradeable devices include USB memory and network device. To update the network, the current DVR should have been connected to the network. Upgrade via the proxy server may not be enabled due to the restricted access. System Management System Information Settings System Information Software Version System Format Broadcast v1.
using the DVR Settings You can copy and import the DVR settings by using a storage media. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. System Management Settings System Information Storage Device 2. Select . A window of storage device and load factory default appears.
Event Log Event log shows recorded events on alarms, motion detections and video loss. It also shows the log and its timestamp. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Select . Log Information System Log Search Day First Page 4. Set Search Day, Channel and Type and the press . Last Page CH All CHs Type View all No.
using the DVR SETTING THE DEVICE You can setup Camera, Storage Device, Remote Device, POS Device and Monitor. Camera Setting the Camera You can set Video, Audio, Channel Name and Dwell Time of a Camera. Using the mouse may help make setup easier. 1. Press the [MENU] button on the remote control. Logout Return 2. Use the left/right button (◄ ►) to select . Device setting menu is selected. Device 3. Use the up/down buttons ( ) to move to , and press [ENTER] button.
• CH Name : Up to 15 characters including blanks are allowed. (The first character should not be empty.) Refer to “Using Virtual Keyboard”. (Page 30) • SEQ-Dwell Time : You can set the dwell time between channels for the Live screen and Spot Out. If set to , the channel is not listed in the Auto Sequence mode. Press the to initialize settings back to the default 50. • Privacy Region : You can specify a certain area of the camera video to be protected for your privacy.
using the DVR Setting the PTZ To use Camera’s PTZ functions, ID and protocols of each camera and DVR should be matched. For other settings, refer to the “Remote Devices” settings. (Page 42) Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Select . A window of PTZ settings appears. 3. Use direction buttons ( ◄ ►) to move to a desired item, and select it.
Formatting You can format a storage device. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Select . A window for selection of device for formatting appears. Storage Device Format Device Device HDD Alarm Select HDD 1 Used/Total Used 0G/499.49G Internal USING THE DVR 3. Use direction buttons ( ◄ ►) to select a device to be formatted. Format OK 4.
using the DVR M status means that the HDD is operating but it has problems that require technical examination. ( ) appears on the Live screen. status means that the HDD has defect and requires immediate replacement. ( ) appears on the Live screen. 4. When the HDD Alarm setup is done, press . Remote Devices You can set the RS-485 communication for use of PTZ Camera and system keyboard with the DVR. Using the mouse may help make setup easier. 1.
• POS Device Setup : Sets the communication setups for the POS device and DVR. It is independent to the Remote Device setup. POS Device POS USE POS Device Setup POS CH 1 None Preset No preset 2 NoneSetup POS Device 3 4 If selected a channel input field, “Sync Channel Setup” window appears.
using the DVR Monitor You can select which item(s) to be displayed on the screen. Setting the Monitor Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Select . 3. Use direction buttons ( ◄ ►) to move to a desired item, and set the value. • Event Display : Sets the dwell time of the event channel display on the monitor when an event occurs.
Setting the Spot Out You can set the DVR to output information / video apart from the monitor out. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Select . The number of Spot Out terminals differs according to the Monitor Spot Out Monitor Spot Out 1 SEQ Event Display OFF Mode All Set Mode USING THE DVR model. 3.
using the DVR SETTING THE RECORDING You can setup scheduled recording, event recording and other recording related settings. Recording Schedule Make your reservation on a date and time to schedule the recording on specified time. Using the mouse may help make setup easier. 1. Press the [MENU] button on the remote control. Logout 2. Use the left/right button (◄ ►) to select . Record menu is selected. 3. Use the up/down buttons ( ) to move to , and press [ENTER] button.
Recording Color Tags Color Function White No Recording Orange Continuous Blue Event Green Both(Cont&Evnt) Description No schedule / event recording Scheduled recording only Event recording only Both scheduled / event recordings USING THE DVR Each press of a selected cell will cycle through --. Event Record Duration You can set the beginning and ending point of a recording on an event. Using the mouse may help make setup easier. 1.
using the DVR Setting Event Recording Properties You can set each channel’s resolution, quality and fps for event recordings. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. REC Quality & Resolution Event Standard Remaining count : 4CIF(L) : 2 2. Select . Event recording setup window appears.
SETTING THE EVENT You can set recording options for sensor, motion, and video loss event. Sensor Detection You can set the sensor’s operating condition and connected camera, as well as alarm output and its duration. Using the mouse may help make setup easier. Logout Return 2. Use the left/right button (◄ ►) to select . Event setting menu is selected. Event Sensor Detection Motion Detection Video Loss Detection Alarm Schedule 3.
using the DVR Motion Detection You can set target detection region and motion, as well as the alarm signal output. When the motion detection region is set, it detects motion within the area. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. A window of motion detection area setup appears. Motion Detection Mode CH 2. Use direction buttons ( ◄ ►) to move to a desired item, and set the value.
Video Loss Detection You can set the alarm to be generated on a camera disconnection, which causes a video loss. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to
using the DVR BACKUP You can check the backup device and set the backup schedule by channel or by time. The product only supports external HDD of USB memory and USB type. (Page 94) Setting the Backup You can backup the desired data to a connected device. Using the mouse may help make setup easier. 1. Press the [MENU] button on the remote control. Logout 2. Use the left/right button (◄ ►) to select . Backup menu is selected. Return Backup Backup 3. Press the [ENTER] button.
5. When the backup setup is done, press . If no available device is recognized for backup, button is not activated. J The application may slow down during the backup. You can switch to the menu screen during the backup in operation, but playback of data is not available. If backup has failed, select “Device > Storage Device” and check the free space of the HDD and check also if the HDD is properly connected.
using the DVR • IP, Gateway, Subnet Mask, and DNS - For : You can directly input IP address, Gateway, Subnet Mask and DNS. - For : IP address, Gateway, and Subnet Mask are set automatically. - For : IP address, Gateway, and Subnet Mask are set automatically. • User ID, Password : In case you selected ADSL, provide the “User ID” and its “Password”. M Connection Mode Connection Protocol Connection Mode ADSL Bandwidth 600kbps IP 192.168. 1.200 Gateway 192.168.
Connecting and Setting the Network Networking may differ from the connection method, check your environment before setting the connection mode. When no router is used • Static IP mode - DVR Network Settings : Set the in menu of the connected DVR to . Consult your network manager for IP, Gateway and Subnet Mask. • Dynamic IP (DHCP) mode - Internet connection : Connect the DVR directly to a cable modem, DHCP ADSL modem or FTTH network.
using the DVR When a router is used J To avoid IP address conflict with the DVR's static IP, check followings : • Setting the DVR with a static IP - Internet connection : You can connect the DVR to a router which is connected to an ADSL/Cable modem or a router in a Local Area Network (LAN) environment. • Setting the DVR Network 1. Set the in menu of the connected DVR to . 2.
DDNS You can set the DDNS site for a remote user’s network connection. Using the mouse may help make setup easier. 1. Use the up/down buttons ( ) in window to move to , and press [ENTER] button. 2. Use virtual keyboard to enter user inputs. Refer to “Using Virtual Keyboard”. (Page 30) DDNS DDNS Site iPOLiS Host Name www.samsungip... User Name User Password http://www.samsungipolis.
using the DVR Mailing Service You can send an e-mail to a DVR-registered user at a specific time interval, or if an event occurs. M If an event occurs with a channel where the camera’s video is set to or the remaining recording count is set to , only the text notification will be sent to the applicable email address. SMTP Setting Sets the SMTP mail server. Using the mouse may help make setup easier. 1.
Group Setting You can set the group to whom the e-mail is sent, and specify the permission for each group. You can add recipients for each group in the menu item. The recipient is set separately from the DVR user group. Using the mouse may help make setup easier. 1. In the setting window, press the up/down ( ) button to move to and press the [ENTER] button. 3. Use direction buttons ( ◄ ►) to move to a desired item and set the value.
using the DVR CONTROLLING A PTZ DEVICE The DVR enables you to adjust the settings of a PTZ camera as well as an ordinary one to your preference. PTZ Device The PTZ device can be activated only if a channel in connection with the PTZ camera is selected. Getting started with PTZ The PTZ camera is available, only if a channel is selected, in the following way : Using the remote control buttons Scene Mode 2011-01-01 01:10:25 Press the [PTZ] button on the remote control.
• Focus : Enables you to adjust the focus manually. • Auto Pan : The camera automatically runs between the two points that you selected. • Scan : The camera moves to the preset points in the specified sequence. If multiple presets are specified, the PTZ camera will automatically move to all of the preset points one at a time. • Pattern : Makes the PTZ camera remember and follow the past route.
search & play SEARCH You can perform the search for recorded data by the time or by the search criteria such as an event. You can access the menu directly in Live mode. 1. In Live mode, right-click any area of the screen. The Live menu appears. Scene Mode 2011-01-01 01:10:25 Spot Out Audio Off Freeze 2. Select . Or, press the [SEARCH] button on the remote control. Stop Alarm Record Play Search Backup Main Menu Shutdown Hide Launcher Logout 3. The Search menu appears.
• Zoom In : The map enlarges in detail. It will switch in the sequence of 24 hours - 16 hours - 8 hour - 4 hours. • Zoom Out : The map will switch in the reverse order of the detailed mode above. It will switch in the sequence of 4 hours - 8 hour - 16 hours - 24 hours. M Time Search Go to First 2011-01-01 Go to Last Overlapped Data List1 Zoom In Zoom Out 00:01 All Data CAM 01 CAM 02 CAM 03 2011/01/01 00:01:17 CAM 04 Standard Schedule Motion Sensor V.
search & play POS Search You can search for data in the POS device that is connected to the DVR. You can use the mouse to select the related items. 1. Select in the menu. The item will be active only if you check the “Use POS” option from “Device > POS Device”. (Page 42) POS Search Date/Time 2011-01-01 02:41:18 Case Sensitive Overlapped Data List1 2. Use direction buttons ( ◄ ►) to set the search criteria and press the [ENTER] button.
PLAYBACK Play You can play data stored in the HDD and backup a desired portion of the data. Using the mouse may help make setup easier. 1. In Live mode, click in the right-click menu or < > in the launcher menu, or press the Play button on the remote control. Scene Mode 2011-01-01 01:10:25 Spot Out Audio Off SEARCH & PLAY Freeze Stop Alarm Record 2. Use the up/down button ( ) to select a menu. Play For data search, refer to .
search & play Using the Playback Button REC Part Names Functions Play Timeline Indicates the current playback point, and can be used to move. b Skip Backward Moves backward by unit time. c Backward Fast Play Used for quick backward search while in Play. Backward Slow Play Used for backward frame-by-frame search while in PAUSE. Step Backward Moves backward by one frame at a time. Pause Stops playing the current video temporarily.
web viewer INTRODUCING WEB VIEWER What is Web Viewer? WEB VIEWER Web Viewer allows remote access to your DVRs. You have access to live video, archived video, PTZ control (if configured), etc. PRODUCT FEATURES • Remote connection using the browser • PTZ camera control enabled • Supports 1, 4 camera viewing formats (maximum of 4 cameras in the list). • Gets JPEG, BMP format images to print and save to “Print or Save JPEG, BMP format images”.
web viewer CONNECTING WEB VIEWER 1. Open your web browser and type the IP address or URL of DVR into the URL address box. M The basic URL of the DVR is as following in case of MAC address : http://www.samsungipolis.com/Product domain (registered at the iPOLiS web site) You can also use registered URL which setups up in the Setup menu of your DVR. 2. Set the Admin ID and password same to those of the DVR Admin. For general users, enter the DVR user ID and password.
5. You may have “Windows Security Alert” that attempts to block this with the Windows Firewall. In that case, click to start Web Viewer. 6. Installation is complete. Now you can see the main screen of Live Viewer. WEB VIEWER USING LIVE VIEWER The Live Viewer screen consists of following : This displays the IP address and the model name of the connected DVR. b These menus consist of , , , . c These buttons are used for the screen split and full screen mode.
web viewer OSD INFORMATION DISPLAY The channel number, video size, and IP address of the connected DVR are displayed. b This icon will appear if the audio signal is currently being output. c The current date and time will be displayed according to the selected time information display setting or . Alarm icon appears when alarm is issued. It disappears when pressed the [ALARM] button of the DVR. Motion icon appears when motion is detected.
CONNECTED DVR This displays the IP address and the status of the connecting DVR. M Connection failure message No Response : Appears when the DVR does not respond. Access Denied : Appears when the maximum number of users is exceeded. The number of simultaneous connections are limited to 4. WEB VIEWER Setting the display of the OSD time information Select or for the OSD time information display setting.
web viewer SAVING THE LIVE SCREEN ON THE PC • CAPTURE : Saves the current screen into a BMP or JPEG file. M The default saving path is “C:\Program Files\Samsung\Dvr Web Viewer\SnapShot\Live”. To change the saving path, click button and then select the path you want. For Windows Vista or 7, the saving path is “C:\users\ (user ID)\AppData\LocalLow\Samsung\DVR Web Viewer\ SnapShot\” by default.
CHANGING THE LIVE SCREEN CHANNEL • Blue numbers : The channel connected to the current live screen • Gray numbers : The channel not connected to the current live screen If you select 4-split mode, the channel button for each of cameras 1 ~ 4 will turn blue. WEB VIEWER USING PTZ CAMERA Click the direction buttons to control the camera. •< > You can zoom in or out an image by using the ZOOM button. •< > You can adjust the entering light amount by using the IRIS button.
web viewer • Preset : Moves the lens direction to a preset direction. 1. If you click a preset, the camera moves to the selected preset's position. 2. You can delete the selected preset or all presets. 3. You can save a new preset number and name. M You can save presets up to 20. • Auto Pan : Moves the camera lens direction between 2 points set for the camera. • Scan : Moves the camera lens direction between 2 preset points of the camera.
USING SEARCH VIEWER WEB VIEWER The Search Viewer screen consists of following : This displays the IP address and the model name of the connected DVR. b There are 4 tabs available: , , , . c Switch to a split mode. Shows the IP address and model name of the connected DVR. Select to turn the sound on/off. These buttons are used for capture, print, and save the image. This displays a calendar at which you can search the recorded video.
web viewer SPLIT-SCREEN You can change the split mode by clicking each number icon. SINGLE MODE QUAD MODE > button. • Click < The screen displays the selected camera connected to the DVR in “SINGLE MODE”. • Click < > button. The screen displays the selected camera connected to the DVR in “QUAD MODE”. CONNECTED DVR The IP of the connected DVR will be displayed. Select to turn the sound on/off. M Connection failure message No Response : Appears when the DVR does not respond.
SAVING THE LIVE SCREEN ON THE PC • CAPTURE : Saves the current screen into a BMP or JPEG file. M The default saving path is “C:\Program Files\Samsung\Dvr • PRINT : Print out the current screen. It also prints IP address, time, camera number and current event state. • RECORD : While in playback, press this button saves the video data of the selected channel as an AVI file. (It is saved in the designated folder on your PC.) To stop recording, click this button again.
web viewer SEARCHING THE RECORDED VIDEO IN THE CALENDAR If the video data has been recorded on a date, the date is distinguished in green. If you click the date, the recorded video information is displayed in the time line. When you click , it will be synchronized with the system time (date) of the current PC. SEARCHING THE RECORDED VIDEO IN THE TIMELINE It displays the recorded video data status on the DVR after a date is selected.
CONTROLLING PLAYBACK WEB VIEWER Fast Backward : Play the video reversely. (at x2 ~ x64) b Reverse Play : Performs Reverse Play. c Play : Performs playback. Fast Forward : Play the video forward. (at x2 ~ x64) Go to First : Moves the beginning time of recorded video in the time line. Step Backward : Performs one step reverseplay by one frame. Pause : Stops the playback temporarily. Step Forward : Performs one step forward by one frame.
web viewer • Time Synchronization Setup Set the time synchronization. • Display Date Format : Set the date type. Time : Select a time format to display on the screen. • DST (Daylight Saving Time) DST is displayed an hour ahead of the standard time of the time zone. • Language Select a preferred language for the DVR. Holiday You can set specific dates to Holidays according to your preferences. For more information, refer to in the menu.
• Group Users are classified into groups and the permission can be set according to the group. First of all, add a group. WEB VIEWER • User You can add, change or remove a user or users. • Setup You can set the user permission. System Management For more information, refer to in the menu. (Page 34) • System Information You can see information of the current system. Check the software version, broadcast format and MAC address.
web viewer Device You can check a list of devices that are connected to the DVR and configure the necessary settings. Click in the menu screen. For more information, refer to “Setting the Device”. (Page 38) Camera • Camera You can configure the settings of the camera that is connected to the DVR. • Privacy Region You can specify a certain area of the camera video to be protected for your privacy. • PTZ You can configure the settings of the PTZ camera that is connected to the DVR.
Storage Device You can check and change the settings of the storage device. • Device You will see a list of storage devices that are connected to the DVR. You can check the type, used/total, usage and status of the device. WEB VIEWER • HDD Alarm You can set the alarm output channel and the alarm duration for an error. Remote Device You can see a list of remote devices including PTZ cameras and system keyboards that are connected to the RS-485 port of the DVR and configure the necessary settings.
web viewer Monitor • Monitor You can configure the monitoring screen settings and set the output system. • Spot Out With the monitor connected via the SPOT port, if there occurs an event such as Sensor, Motion, or Alarm, you can select a video output mode for external monitoring. • Mode You can switch between live mode and play mode.
Record For more information, refer to . (Page 46) Recording Schedule If you set a recording schedule for a specific date and time, the recording will start at that specific time. WEB VIEWER - Apply to All CH : Click to display the confirmation window. Event Record Duration You can set the start and end times of recording that will be activated if an event occurs.
web viewer REC Quality & Resolution • Standard/Event You can set the resolution, frame rate and recording quality for each channel. Record Option You can set the Disk End Mode. Event For more information, refer to . (Page 49) Sensor Detection You can set the sensor operation mode and the synchronized camera as well as the alarm output type and the duration.
Motion Detection You can set the motion detection mode and the sensitivity as well as the alarm output type and the duration. WEB VIEWER • Motion Region Set the target motion detection area Video Loss Detection You can set the alarm output time if a video loss occurs. Alarm Schedule You can schedule the alarm output according to the day of the week and the time. The default setting is Event Sync, which activates the alarm only if an event occurs.
web viewer Network For more information, refer to . (Page 53) Connection A remote user can access the DVR via the network to check the current mode and the IP address. • Connection You can set the network connection route. • Protocol You can configure the protocol related settings. DDNS You can check the DDNS settings.
Live Transfer A remote user can set the images of the DVR. • Live Transfer You can specify the quality of the image data that a remote user will receive. WEB VIEWER Mailing Service You can specify the SMTP server that sends a mail if an event occurs and set the recipient group and users. • SMTP You can set the server that sends mails and specify if you use the authentication process. • Event You can set the event interval and specify which events the server sends mails for.
web viewer • Group You can add a group to receive the mail if an event occurs and set the permission to receive the event mail for each group. • Recipient You can add a user or users who will receive the mail. ABOUT Click . Displays the model name of connected DVR and the version of Web Viewer.
MOBILE VIEWER What is Mobile Viewer? iPOLIS mobile is smartphone application that enables you to connect to DVR (Digital Video Recorder) remotely and control the video playback and PTZ operations (if configured) in real time. 1.X • Remote access via Smart phone • Voice Recognition • 1-split and 4-split modes supported in Live Viewer (However, search is not available).
backup viewer SEC BACKUP VIEWER You can play a file that is backed up in the format of SEC. Backup in the format of SEC will involve in generating two files: one for the backup data and one for the viewer. If you run the backup file viewer, the backup data file will be automatically played. Recommended System Requirements PCs with a lower specification than the recommended below may not fully support forward/backward and high-speed playback.
Name Description / A toggle button. Each time you press this button, the audio output will toggle between activated and deactivated. Audio You can adjust the volume level from 0 to 100. c Screen Printout Prints out the current screen. You should have installed the appropriate printer driver before you can print out the screen. File Tamper Detection / Deinterlace A toggle button. Each time you press this button, it will toggle between activated and deactivated.
appendix PRODUCT SPECIFICATION Item Details Inputs 4 composite video 0.5–1 Vpp, 75 ohm Resolution 704x480 NTSC, 704x576 PAL Frame rate 120fps NTSC, 100fps PAL Resolution 704x480 NTSC, 704x576 PAL Multi Screen display 1, 4, SEQUENCE, PIP Embedded Linux Compression H.
Item Storage Details 500GB SATA HDD External HDD – DVD Writer (Back-up) – USB (Back-up) 2 USB Ports File Forma (Back-up) BU(DVR Player), EXE(Include Player) Password Protection 1 Admin, 10 Group, 10 User per 1 Group Data Authentication Watermark VGA Analog RGB 1024x768 resolution(BNC or VGA selected in booting.) HDMI – Main Composite BNC, 1 Vp-p, 75 ohm Spot Composite – Loop Outputs – Inputs/Output 1 Line in(CH1) / 1 line out(RCA) Compression G.
appendix PRODUCT OVERVIEW 0.2 (0.01”) 44 (1.73”) 50 (1.97”) DIGITAL VIDEO RECORDER SRD-440 255 (10.04”) 96_ appendix 215 (8.46”) 203.5 (8.
DEFAULT SETTING This returns the factory default settings. The settings are made as follows; • Use System/Load Factory Default in MENU The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user.
appendix Category Details Remote Device Device Factory Default Baudrate 9600 Parity None Data 8 Stop bit 1 Transfer Type Half Duplex System Keyboard OFF Remote Control ON(00) POS Device OFF Monitor Monitor Event Display OFF Display All Display Position Setup 30 Spot Out 1 CH1 ~ CH4 Event Display OFF Live Mode ALL Play Mode ALL Spot Out Mode Recording Schedule Channel 1 Event Event Record Duration PRE Event OFF POST Event 1 min Normal Recording Recording REC Qua
Category Details Sensor Detection Motion Detection Video Loss Detection Alarm Schedule Sensor Operation OFF Camera Camera No. Alarm None Duration 10 sec Mode OFF Sensitivity Level10(high) Alarm None Duration 10 sec Motion Region All Area Video Loss State OFF Alarm None Duration 10 sec Alarm1 Event Sync Connection Connection Mode Protocol DDNS Connection Mode Static IP Bandwidth 2Mbps IP 192.168.1.200 Gateway 192.168.1.1 Subnet Mask 255.255.255.0 DNS 168.126.63.
appendix TROUBLESHOOTING Symptom Countermeasures The system does not turn on and the indicator on the front panel does not work at all. Check if the power supply system is properly connected. Check the system for the input voltage from the power source. If the problem persists even after you have taken the above actions, check the power supplier and replace it with a new one if neccessary. Some channels display just a black screen even if they receive video sources.
Countermeasures I've found that the DVR does not recognize as many disks as installed when I have connected multiple external HDDs to the DVR. It takes time for the DVR to recognize multiple external HDDs. Try again in a moment and if the problem (of failure to recognize as many HDDs as connected) persists, it may occur due to a mechanical error of the HDD installed. Try again with a different HDD. A message of “Need to reset date/time.” Is displayed on the screen.
appendix Symptom Countermeasures Recording does not work. If your player does not display a Live image at all, that indicates recording does not work so first check if you see an image on the screen. Recording does not work if the recording settings are not properly configured. 1) Manual Record: Press the [REC] button on the remote control to start recording. 2) Scheduled Record: Specify a desired time in Menu – Record Recording Schedule. Recording will start at the specified time.
OPEN SOURCE LICENSE REPORT ON THE PRODUCT The software included in this product contains copyrighted software that is licensed under the GPL/LGPL. You may obtain the complete Corresponding Source code from us for a period of three years after our last shipment of this product by sending email to help.cctv@samsung.com If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged.
of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License.
How to Apply These Terms to Your New Programs GNU Lesser General Public License instead of this License. If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users' freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to prohibit the practice for those products.
The Corresponding Source for a work in source code form is that same work. 2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work.
offer spare parts or customer support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms: a) Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or b) Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or c) Prohibiti
litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it. 11. Patents. A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor's “contributor version”.
and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any version ever published by the Free Software Foundation.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
the work for the customer’s own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random Hacker.
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Fax : +1-201-373-0124 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com www.samsungipolis.com SAMSUNG TECHWIN EUROPE LTD.
