! ! ! ! ! ! ! ! ! ! 4/8/16 CH H.
This symbol is intended to alert the user to the presence of unprotected “Dangerous voltage" within the product's enclosure that may be strong enough to cause a risk of electric shock. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
All the safety and operating instructions must be read before the unit is operated. • Make sure to switch the power off before you install the DVR. • There is the danger of an electric shock if the DVR is opened by an unqualified service engineer or installer. • Avoid using the DVR outside of the reference temperature and humidity indicated in the specification. • Avoid exposing the DVR to violent movement or vibration.
TABLE OF CONTENTS Chapter 1 FEATURES .........................................................................................................1 Chapter 2 PACKING DETAIL ...............................................................................................2 Chapter 3 LOCATION AND CONTROL ...............................................................................3 3.1 Front Panel Controls...............................................................................................3 3.
.3 System..................................................................................................................26 5.3.1 HDD............................................................................................................26 5.3.2 Clock...........................................................................................................27 5.3.3 Video Standard ...........................................................................................28 5.3.4 Language...............
Chapter 8 COPY OPERATION AND MENU SETUP .........................................................46 8.1 Copy .....................................................................................................................46 8.1.1 Copy to USB Storage Device......................................................................46 8.1.2 Copy to DVD±RW.......................................................................................47 8.1.3 Stop Copy ....................................................
Chapter 1 FEATURES H.
Chapter 2 PACKING DETAIL 1. DVR 2. Client Viewer Software CD 5. Power Cord 3. User Manual 6. Power Adapter CONTENTS 1. DVR 2. Client Viewer Software CD 3. User Manual 4. Remote Controller 5. Power Cord 6. Power Adapter 7. Battery 2 4. Remote Controller 7.
Chapter 3 LOCATION AND CONTROL 3.1 Front Panel Controls 2 1 4 3 13 14 Item 15 5 6 16 17 19 18 7 8 20 9 10 11 12 25 21 22 23 24 Description 1 DVD-RW A DVD-RW drive is installed in the front bay. (sold separately) 2 EJECT Press EJECT button to open/close the DVD-RW drive. 3 IR RECEIVER Infrared signal receiver for the IR remote controller. Do not block the receiver as a clear line of sight is required for proper operation.
9 ALARM RESET / LEFT (a) resets the alarm buzzer DIRECTION BUTTON ( ) (b) left pans in PTZ mode (c) navigates left in the menu screen (d) moves the zoom box left in zoom mode 10 MENU / UP DIRECTIONAL (a) accesses the main menu screen BUTTON () (b) tilts up in PTZ mode (c) navigates up in the menu screen (d) moves the zoom box up in zoom mode 11 PIP / LOOP PLAYBACK (a) activates the picture-in-picture mode CLEAR / DOWN (b) tilts down in PTZ mode DIRECTIONAL BUTTON () (c) navigates down in
22 ENTER / STATUS / HOME (a) executes the selected function in the menu screen or enters the selected submenu (b) accesses the status window from the main screen (c) returns the PTZ camera to “home” mode in PTZ mode (d) increases the digital zoom ration in zoom mode 23 AUTOMATIC SEQUENCE / (a) activates and deactivates the automatic channel sequence FOCUS OUT / DECREASSE (b) focuses out in PTZ mode VALUE / SECTION A (c) decreases the value of a selection in the menu screen (d) sets the starting poi
3.2 Real Panel Connectors 1 4CH DVR 2 6 4 CAUTION ! ON WARNING: VIDEO IN 1 3 SPOT AUDIO IN VGA OFF ETHERNET 4 1 8CH DVR VIDEO OUT PS/ 2 OUT 3 5 2 4 DC 12V 1 2 3 4 G D+ DNO CM G 2 SENSOR G 485 RL1 G 7 8 10 9 11 6 ( #5 - 0$ %)6 / 01 2)$ &),3 ,(- /0 ()1. $(2 '$)%$ -)$4 ,% $% 7 #/ % 0% "8 - $)/ ,' 5( ,)-.,)/ 01 2)$ & &0 /,)$/), 3,( - /0()1.
3.
3.4 Mouse Control LIVE MODE Single Channel Display Move the cursor to the desired channel and double left click.
Chapter 4 INSTALLATION 4.
4.2 Hard Disk Installation First, please remove the HDD holder from the DVR machine. (Pic1)& (Pic1) Lock HDD holder symmetirically in the two sides of HDD. (Pic2, Pic3) (Pic2) (Pic3) Insert the SATA cable and power cable into SATA HDD.
Lock the HDDs onto DVR machine. (Pic5)& (Pic5) Insert the SATA cables into the sockets on the main board (Pic6). Make sure the HDD1 cable insert into HDD1 socket. Now, the installation was finished (Pic7).
4.3 Main Devices Installtion 4.3.1 Camera * Connect a female BNC connector of each camera to a male BNC connector, “CAMERA IN” port. 4.3.2 Audio Audio Input - AUDIO IN: Connect the RCA Line Jack of the relevant equipment (for example, a camera with a built-in microphone) to the AUDIO IN port. Audio Output - AUDIO OUT: Connect the RCA Line output to a monitor with a built-in speaker. NOTE - This DVR can be connected only with a line audio and not support a microphone for audio input and output.
4.3.3 Monitor ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! SPOT MONITOR VGA MONITOR MAIN MONITOR DVR supports two types of monitor output, one is Composite output (BNC connector); the other one is VGA output (DSUB-15). But you can just select one monitor output type at a time. * Composite Output: !"# Power off !$# Press the MENU button and CH3 button at the same time !%# Power on !&# When you hear a beep sound, it means images already output to the Composite port. Now you can release the buttons.
4.4 sensor Input ! 16CH: SENSOR 1~SENSOR 16 8CH: SENSOR 1~SENSOR 8 4CH: SENSOR 1~SENSOR 4 4.4.1 Sensor Input Menu Setup Enter EVENT -> SENSOR INPUT menu to select the correct sensor input type which connected with DVR. Select the right sensor type according to the type of installed sensor with the unit. - NORMAL OPEN: The sensor is open in normal times. - NORMAL CLOSE: The sensor is close in normal times.
4.5 RS-485 ! RS485 is use for connect to external device, such as keyboard or PTZ camera. ! 4.5.1 RS-485 Menu Setup Enter LINK -> RS485 menu to set the parameters of RS-485 device which connected with DVR (The parameters must the same with the device). ! ! 4.5.2 PTZ Camera Installation Connect the PTZ camera to DVR RS-485 interface (D+ to D+; D- to D-), and then connect the camera output to the desired channel.
! ! ! 4.5.3 PTZ Camera Operation 1. Select the desired PTZ camera channel. 2. Press the PTZ button to enter the PTZ mode. 3. Use the direction buttons to change camera position. 4. Press Z(+) and Z(-) buttons to control the camera zoom in and zoom out. 5. Press the PTZ button again to exit the PTZ mode. ! 4.5.4 PTZ Camera Preset Mode 1. Select the desired PTZ camera channel. 2. Press the PTZ button to enter the PTZ mode. 3. Press the PRESET button to enter the “PTZ(PRESET)SET” mode. 4.
Preset point is a convenient usage of PTZ camera. It is a preset user-defined camera position; user can move the camera position very quickly when needed. Total programmable capacity of 16 preset locations. ! ! 4.6 Relay Output ! ! The relay device should be set to NO (Normal Open) and it will change to NC (Normal Close) when an event has been triggered. Enter EVENT -> RELAY OUTPUT menu to select the Relay type which connected with DVR.
Chapter 5 BASIC OPERATION AND MENU SETUP 5.1 Basic Operation 5.1.1 Power ON/OFF After the connection of power adaptor and other devices (HDDS) with this DVR, turn the power on. a. The video signal system (NTSC or PAL) is automatically detected. b. Power Failure Recovery This DVR automatically reverts back to programmed record parameters upon power restoration. If there is no video signal, the video signal system is set to NTSC. Do not input the PAL type video signal or it may!cause the DVR’s malfunction.
c. Freeze ! ! ! ! ! FREEZE ! This function allows users to freeze live view mode at any given time. 4CH DVR supports only single screen mode. Press [FREEZE] at single screen mode to freeze the image and press again to release this function. 8/16CH DVR can support both single and multi screen mode. The operation is the same as 4CH DVR for single screen mode. For multi screen mode, press [FREEZE] at multi live screen, the message will be shown at upper-left, but no channels will freezed.
This page shows the present RECORDING BITRATE of DVR. High bitrate means it’ll need more HDD space. 5.1.4 Audio Control Audio ON/OFF: Press the FUNCTION button and then press the “AUDIO (0)” button to open/close the DVR audio function. You can hear audio of selected channel regardless of monitoring screen. ! 5.1.5 PIP Mode # Select a single camera in live view, and then press the PIP button and the following screen will be displayed (For example: CH1).
! # Select the desired camera channel. $ Press the D-ZOOM button, the indication screen appears on the main screen. % Press , , , buttons to select the desired location. & Press the ENTER button to change the zoom size x2 ~ x4. ' Press the ESC button to exit this screen. 5.1.7 Menu Operation # Press the MENU button to enter the main menu screen. $ Move the cursor to desired position using the ((( buttons, then press the button to enter each submenu.
5.2.1 Auto Sequence To set the length of time for switching each channel in the AUTO SEQUENCE mode. The value is from 1SEC to 60SEC and the default is “3SEC”. ADD AUTO SINGLE: If selected OFF, every single channel will be skipped in the AUTO SEQUENCE mode. The default is “OFF”. VIDEO LOSS SKIP: If selected ON, every VIDEO LOSS channel will be skipped in the AUTO SEQUENCE mode. The default is “ON”.
5.2.2 Display To decide which information will be displayed on the screen: ! ! ! ! ! ! ! HDD Free Space If the value is ON, the remaining capacity of the fixed HDDs will be displayed on the screen. The default is ON. ! HDD Free Space Mode The default is “PERCENT”. PERCENT: Remaining capacity of the fixed HDDs will be displayed on the screen in percent. GIGABYTE: Remaining capacity of the fixed HDDs will be displayed on the screen in gigabyte.
5.2.3 Title To name or modify the channel title. Press the ENTER button after selecting desired channel and the following screen appears: Select the character using the , , , buttons and then press the character table. button. Press the ESC button to exit 5.2.4 Multi Screen Enter one of the five modes (4, 7, 9 for 8CH and 4, 7, 9, 10, 13 for 16CH) and change the selected channel to multi-split screen.
! SELECT: “LV&PB&NW”, “PB&NW”, “LV&NW”, “LV&PB”, “NETWORK”, “PLAY” and “LIVE”. LV(LIVE): To covert selected channels on live screen. PB(PLAY): To covert selected channels on playback screen. NW(NETWORK): To covert selected channels on network viewer screen. COVERT TITLE DISPLAY: Show the “COVERT” text in the camera title position or not. ! 5.2.6 SPOT SPOT MODE - MANUAL: Manually select the channel of spot monitor. - EVENT: Event channel will be displayed automatically on spot monitor.
5.2.7 Camera Change the values shown on the screen to adjust the BRIGHTNESS, CONTRAST, HUE and SATURATION of each channel. The value is from 0% to 100% and the default is “50%”. 5.3 System ! 5.3.1 HDD ! REC HDD INITIALIZE: Select YES and press ENTER button to format the HDD.
Note: All data will be cleared after initialized. Please be careful. ! 5.3.2 Clock System clock adjustment. DATE&TIME Manually adjust the Date and Time values. - DATE: YYYY/MM/DD YEAR/MONTH/DAY - TIME: HH:MM:SS HOUR:MINUTE:SECOND ! TIME ADJUST ! # If the INTERNET TIME ADJUST is “ON”, system time will be adjusted to the time offered by the internet server. $ If the INTERNET TIME ADJUST is “ON”, please set the IP address of SELECT TIME SERVER.
& If the DAYLIGHT SAVING TIME is “ON”, please set the starting date and time and end date. ! 5.3.3 Video Standard Select from “AUTO”, “NTSC” or “PAL”. The default is “NTSC”. If you select “AUTO”, this DVR can detect NTSC/PAL automatically. ! 5.3.4 Language Select the system language. Available languages: ENGLISH, POLISH, SPANISH, RUSSIAN, CHINESE (T) (Traditional Chinese), FRENCH, TURKISH, GERMAN, ITALIAN, PORTUGUESE.! 5.3.
5.3.7.2 Set Passwork Select the administrator or user1~4 to change the password and then press “ENTER” button. Insert your desired password and retype again using the CAMERA/ NUMBER INPUT buttons. NOTE: - You can use only 0~9 number buttons to setup the PASSWORD. - The default passwords as: ADMIN is 11111111, USER1 is 22222222, USER2 is 33333333, USER3 is 44444444, USRE4 is 55555555. CAUTION: For security reason, please change the password after purchasing 5.3.7.
5.3.7.4 DVR Menu Setup 1. Menu Initialize If select YES, all menu setting will be restore to factory default. NOTE: After initialized, HDD data will not be deleted. 2. LOAD MENU FROM FILE To download the DVR menu settings from file that was saved in the USB storage device. 3. SAVE MENU TO FILE Save the menu settings to the USB storage device. Note: To copy and upload the menu setting only from front USB port. ! 5.3.8 Firmware Upgrade You can update the DVR firmware through the USB interface.
Chapter 6 RECORD OPERATION AND MENU SETUP 6.1 Record Operation The DVR provide three methods of recording for your choice as following: 1. Manual Recording: You can just press the button on the front panel during any LIVE monitoring time. Press the RECORD button again to exit recording mode. 2. Schedule Recording: You can prearrange the schedule recording time (RECORD -> RECORD SETUP) by applying Front Panel Control or Mouse Control.
-“ (Green) ” : Schedule Recording mode -“ (Red) ” : Event Recording mode (Motion detection/ Video loss/ Sensor) -“ (White) ” : Not Recording! These three recording mode all needs a corresponding RECORD SETTINGs such as IMAGE SIZE, RECORD FRAME… DVR will follow the menu setup to do the recording. 6.2 Quick Setup This menu is simply used when user want to change just a few important settings. ! QUICK SETUP If QUICK SETUP setting is “ON”, DVR will record data according to the QUICK SETUP settings.
EVENT Select a kind of EVENT of “ALL”, “ALARM”, “V-LOSS”, “MOTION”, “ALARM&LOSS”, “ALARM&MOTION”, “LOSS&MOTION”, “OFF”. The default is “ALL”. If you want to select all kind of event, choose “ALL” and if you don’t want event recording, choose “OFF”. PRE RECORD TIME When video loss, alarm or motion is detected, DVR will store pre-recorded data during the selected time. The pre-recording time can be set from 0 second to 5 second and the default is “5”.
6.3 Record Setup If QUICK SETUP setting is “OFF”, DVR will record data according to the RECORD SETUP settings. DVR provides 10 RECORD PROGRAMs, user can use RECORD SETUP menu to arrange the different RECORD PROGRAMs to different time point. For example, you can use higher recording frame to record on workday, and use lower recording frame on weekend. The default RECORD PROGRAM is PROGRAM6. RECORD STATUS: You can find the present RECORD PROGRAM setting in the DVR STATUS page.
NTSC: 720x480/ 720x240/ 360x240 PAL: 720x576/ 720x288/ 360x288 Set the RECORD FRAME for each camera: % - NORMAL: Normal record frame. - EVENT: Event record frame. & QUALITY: Set the record quality of normal recording and event recording. There are three record qualities: Fine(F)/ Normal(N)/ Low(L). ' PRE/POST: Set the time period of PRE RECORD TIME and POST RECORD TIME. PRE RECORD TIME is 0~5 sec, the default is 5 sec. POST RECORD TIME is 0~60 sec, the default is 10 sec.
!!!! CHANNEL Set the camera channel of MOTION DETECTION. SENSITIVITY The higher the number is, the more sensitive. The default is 3. AREA SETUP Move the cursor to the desired area and press ENTER button to save it. Press Z(+) button to select whole area, press Z(-) button to deselect whole area. Mouse operation: Move the cursor to the desired area and right click to enable it. TEST MOTION Test the MOTION DETECTION to see if it matches your demand. 6.4.
! EVENT Set the EVENT RECORD item. Select a kind of EVENT of “ALL”, “ALARM”, “V-LOSS”, “MOTION”, “ALARM&LOSS”, “ALARM&MOTION”, “LOSS&MOTION”, “OFF”. The default is “ALL”. If you want to select all kind of event, choose “ALL” and if you don’t want event recording, choose “OFF”. PRE RECORD TIME When video loss, alarm or motion is detected, DVR will store pre-recorded data during the selected time. The pre-recording time can be set from 0 second to 5 second and the default is “5”.
When QUICK SETUP is OFF: ! Please assign the event type in the RECORD PROGRAM menu and set the EVENT CHECK to ON. 6.5 Other Record Setup 6.5.1 Preview Quality After the DVR and cameras installed, DVR will calculate how long the installed HDDs can record automatically. When using this function, DVR cannot be in any record mode. In the mean time, the image showed will be a littlt bit late than live video.
6.5.2 Audio Record If the QUICK SETUP is OFF, when you want to record audio, the AUDIO RECORD in the RECORD SETUP must set to ON. 6.5.3 Repeat Record ON: When repeat recording, if the HDD is full, DVR will overwrite the recorded data automatically. OFF: Stop to record when the HDD is full. REPEAT RECORD ALARM: When the rest capacity of HDD matches the setting value, DVR will stop to write datas into HDD and show the warming message on the screen. The setting value is 5% ~ 10%. 6.5.
Chapter 7 SEARCH OPERATION AND MENU SETUP SEARCH&PLAYBACK If you want to search the specific record data, you can enter the SEARCH menu through the main menu or press the SEARCH button on the front panel. ! ! ! ! ! ! ! ! ! ! ! ! Instant Playback Press the (DIRECT) button in the LIVE mode, DVR will switch to the PLAYBACK mode instantly and start to play from the button pressing time. Press the DIRECT button again will switch the playback direction.
7.2 Search & Copy You can search the record data from HDD and copy to specific storage device. HDD ID: The HDD (HDD0, HDD1) which the record data saved. The default is NORMAL. The START TIME and END TIME of the selected record data will be shown on the screen.& CHANNEL: Select to playback signal channel or all channels. Select the desired HDD ID, CHANNEL, TIME, and press the ENTER button then you can playback. Press ESC button to go back to the previous menu.
7.4 Event Search Search the record data according to the event. For example, you can see how many MOTION events during the assigned time period. ! ! Select the desired HDD ID, CHANNEL, EVENT, TIME and press the ENTER button, the search relausts will be shown. Select the desired event and press ENTER to playback. NOTE: - When video loss is detected, up to five seconds of pre-recording data is stored on the HDD and the details will be listed in the EVENT LIST. The beep sounds will flicker.
7.6 File Search Search the record data according to the record file in the storage device. If user has more than two DVRs which are the same model (with the same file format), you can save the record data of one DVR to external storage device and play the data on the other DVRs. ! ! Select the desired storage device and press the ENTER button, the search relausts will be shown. Select the desired file and press ENTER to playback. ! 7.7 Bookmark Search Search the record data according to the BOOKMARK.
! 7.9 Search Button Information ! ! ! ! ! SLOW ( ) Press this button to make the speed level which is slower than normal speed (X1) and displayed it at the upper left side of screen as below; (If you press this button again, the playback speed will be changed in the order of the below seven speed level).
DIRECTION ( ) Press this button to change direction to forward ( ) or backward ( ) in playback mode. While playback, one may setup a specific period for repeative palyback. 1. Start playback 2. Press “SEQ” button to set up SECTION A (Starting Position), then the screen will show (A -). 3. Press “FREEZE” button to set up SECTION B (End Position), then the screen will show (A - B). 4. After setting section A-B, DVR starts playback repeating the setup. 5.
Chapter 8 COPY OPERATION AND MENU SETUP To copy the DVR record data, you can enter the COPY menu through the main menu or press the COPY button on the front panel. ! ! ! ! !!! ! ! 8.1 Copy Copy the record data from DVR internal HDD to external storage device. 8.1.1 Copy to USB Storage Device First, please connect the USB devices (DVD Writer, HDD, Card Reader) to DVR and enter the COPY munu: ! MEDIA: Select USB_FRONT HDD ID: The HDD (HDD0, HDD1) which the record data saved.
8.1.2 Copy to DVD) )RW Put the DVD)RW into DVD-ROM and enter the COPY menu: Select the desired MEDIA (INTERNAL CD-RW/DVD), HDD ID, CHANNEL, COPY START TIME, COPY END TIME and press the ENTER button to start the copy. NOTE: - You can see a password input message. Please input the password by the numeric buttons or press ECT button to cancel. - You’ll need this password when opening the file in the network viewer. - When the copy is in process, the copying status (ex.
8.1.4 Continue Copy If the storage device full or error occurs during the COPY process, the “MEDIA FULL OR FAIL PRESS [COPY]” message will be shown on the screen. Press COPY button, the following screen will appear: ! !!! CONTINUE COPY: After change a new media, the COPY process will be continued. FORMAT MEDIA: Format the present storage device. 8.2 Copy Status Review the status of the present COPY process. ! ! ! ! ! ! ! ! ! COPY CUR TIME: Indicate current copying situation among the total copying data.
Chapter 9 NETWORK SETUP AND OPERATION 9.1 Network Setup • This DVR support dynamic IP and static IP. • Remote view from Internet Explorer or DVR Viewer software. DVR Viewer provide plenty functions include menu setup. IE support only simple viewing and playing. • This DVR doesn’t support xDSL, there is a DYNAMIC IP SERVER, but no PPPoE protocol. ! DHCP DHCP is a protocol for assigning dynamic IP addresses to devices on a network., if you want to use dynamic IP, please set the DHCP to “ON”.
NETWORK FRAME Select the desired value to select an image frame to be transported from DVR to network client viewer. Note: NETWORK FRAME is use for the transported image being influenced by Network speed. - STILL: Use when the local network speed is too slow. - MOTION: Use when the normal situation of network speed. 9.2 DVR-Viewer Installation 9.2.
If you don’t need to change the default path, press “Install” to start installation. Installation DVR-Viewer completed. Click on “YES” to install the Roxio UDF Reader. Click on “Next”. Click on “Install”. Click on “OK” and the installation completed.
9.3 DVR-Viewer Control Panel Introduction ! 1 2 3 4 5 6 7 9 10 11 8 12 13 ! ! Items Description 1 DVR List: *+Add/Modify/Delete the DVR connection list or connect to DVR. 2 DVR Search: To scan the available DVRs within a local network area. 3 HDD Search: To search the record data of DVR HDD connect to PC. 4 File Search: Search by record files (Copy from DVR or on PC). 5 Arrange Windows: To auto arrange the windows which open by DVR. 6 Viewer Option: DVR-Viewer setup.
Press button to switch to full screen mode. ! 9.4 DVR-Viewer Operation 9.4.1 DVR-Viewer Software Password When the DVR Viewer is run for the first time, it prompts for the administrator’s password. When you run the software in the future, you’ll need this password. If you don’t want to set a password, please keep it empty. Click on OK to start the program. 9.4.
Add # 1 You can click on the DVR Search button ( ) to auto scan the available DVRs in a local network area: ! Press “Search” button to scan the DVRs, select the desired DVR and press “Add to List”. The selected DVR will be added to the DVR List. # 2 Or input the DVR connection information directly, then click on “Add” to add a DVR. Type: DVR connection type, select “Network” generally. IP/Port/MAC: DVR IP address and connection port (The default is 5400).
# 1 Select the desired HDD, Channel and Video Mode. # 2 Press “OK”, the following window appears: ! # 3 Select the desired Channel and Search Time under the Time Search window, click on “Play” to playback. 9.4.4 File Search Some users copy the DVR record data to DVD or USB storage device. Then use File Search function to search and playback these data on PC. Click on the File Search button, the following window appears: ! # 1 Select the desired search path through “Folder Select”.
9.4.5 Arrange Windows Arrange the windows opened by DVR-Viewer automatically. ! * 1 window * 2 ~ 4 windows ! ! *5 ~ 9 windows *10~16 windows ! ! Double click on one window in multi display mode to extend to full screen. 9.4.
Display: - Channel Title: Show the Channel Title on the screen. - Event: Show the event occured channel as Red on the screen. - Date Time: Show the DVR date and time on the screen. - Frame Rate: Show the Frame Rate on the screen. Play Mode: - Frame Mode: It will playback images in frame mode which is useful for recorded images in high frame rate. This may occurs when moving artifact with recorded images in low frame rate. - Field Mode: It playback images in field mode.
b. Multi Display Mode Click on “MULTI” button to display as Multi Display Mode. Click on “MULTI” again to return to Signal Display Mode. ! ! ! ! ! ! ! ! ! ! c. Auto Sequence Mode Click on “AUTO” button to display as Auto Sequence Mode, and you can also set the sequence time. 9.4.8 DVR Controller Press “Controller” button, a control panel similar to DVR front panel will appears. ! ! 9.4.9 PTZ Controller Use the PTZ Controller to control PTZ camera through internet.
buttons in Move line, then the PTZ camera will move to the preset position. 9.4.10 Setup Click on “SETUP” button and input the DVR ADMIN password, you can enter to the DVR muen setup. ! ! Save To File: Save the DVR menu settings to a file. Read From File: Read the DVR menu settings from a file. Load From DVR: Load the real time settings from DVR to PC. Update to DVR: Update the menu settings in PC to DVR. QUICK SETUP Please refer to 6.2 QUICK SETUP.
! For the rest settings please refer to 5.1.2 SCREEN. RECORD To set the Schedule Record, please click on an hour block and then click “SCHEDULE RECORD ON/OFF”. An hour block when enabled becomes Green. Move the cursor to any time point on the vertical ALL roll, then click on “SCHEDULE RECORD ON/OFF” to cancel record schedule.
! For the rest settings, please refer to 6.3 RECORD SETUP. EVENT Please refer to 6.4 EVENT SETUP. SYSTEM Please refer to 5.3 SYSTEM. LINK Please refer to Chapter 4 and 9.1 NETWORK SETUP. DOWNLOAD Download the Firmware from DVR to PC.
9.4.11 Status Click on “STATUS” button to review the System/Record/Network/Bit Rate status. ! ! 9.4.12 Print Click on the “PRINT” button to make a screen snapshot and save as a file. The size of snapshot is depend on the Record Image Size (D1,Half-D1,CIF).
9.4.13 Copy Copy the DVR images to PC. Select the desired HDD, Time and channel, click on “Copy” button to start copy. The Copying stutus will be shown as below. Click on “OK” button after the copy finished, the file will be saved in C:\Program Files\DVR \DVR-Viewer\Copy automatically. 9.4.14 Search Please refer to Chapter 7 Search Operation and Menu Setup. 9.4.
Chapter 10 ADDITIONAL FUNCTION OPERATION AND MENU SETUP 10.1 E-mail Enter the LINK -> E-mail menu ! SEND E-MAIL Select from “ON”, “OFF”, The default is “OFF”. When SEND E-MAIL set to “ON”, DVR will send a e-mail when an event happened. SMTP SERVER # Move the cursor to SMTP SERVER and press ENTER button to input the IP address. ! $ Select the character using the , , , buttons and then press the ENTER button. % To exit this CHARACTER TABLE screen, press the ESC button.
% To exit this CHARACTER TABLE screen, press the ESC button. USER ID # Move the cursor to USER ID and press ENTER button: ! $ Select the character using the , , , buttons and then press the ENTER button. % To exit this CHARACTER TABLE screen, press the ESC button. PASSWORD # Move the cursor to PASSWORD and press ENTER button: ! $ Select the character using the , , , buttons and then press the ENTER button. % To exit this CHARACTER TABLE screen, press the ESC button. 10.
10.3 Connect the DVR through Internet Explorer Step1. Connect to this web site (IP address: 211.174.251.155) and the following interface will be shown: Step2. Input the IP address of DVR and then click “Connect”. Step3.
Step4. The LIVE image will be displayed. Note1: When first time connecting to this web site, ActiveX component is downloaded and installed automatically. It will take a few minutes. If the Internet Explorer does not allow this installation, please adjust the security option of the browser. Note2: If the DVR cannot be connected, please delete the file “XViewer.dat” on your desktop and try again.
Chapter 11 TROUBLESHOOTING Q: What brand of hard disk does the DVR support? A: DVR supports Western Digital and Seagate hard disks. The maximum capacity is 1 terabyte for each device. Q: What type of DVD disks is competitble? A: DVD-RW (MITSUBISHI 2X-4X, Verbatim 6X, VIO 4X); DVD+RW (MITSUBISHI 1X-4X, Verbatim 6X, PHILIPS 1-4X). Q: Why isn’t PS/2 mouse working? A: User needs to use the mouse together with the wheel. Some functions need this third button.
Chapter 12 SPECIFICATION ! VIDEO SYSTEM INPUT VIDEO 4CH BNC SENSOR STORAGE MAIN OUTPUT 1CH BNC Composite Video / VGA (select from front panel) SOPT OUTPUT 1CH BNC INPUT 1CH RCA OUTPUT 1CH RCA REMOTE - INPUT 4CH ALARM INPUT 16CH ALARM INPUT 1CH RELAY OUTPUT DEVICE 2 SATA hard disks (7,200RPM, 45MHz DMA, MAX. 1TB) OPTION DVD WRITER 1,4 1,4,7,9 ZOOM 1,4,7,9,10,13,16 2X Graphic OSD COMPRESSION RESOLUTION H.
SEARCH MODE PLAYBACK SPEED DEVICE BACKUP FILE Time, Calendar, Event, File, Block Normal, REW&FF [1x/2x/4x/16x/32x/64x/128x], Picture to Picture, Pause Internal: HDD, DVD Writer/ External: USB 2.0 Devices H.264 compression and AVI format (converted by client viewer) COMPRESSION H.264 NETWORK NETWORK 16CH Client Viewer, Web Browser INTERFACE SPEED PROTOCOL 120 Frames per second TCP/IP, SMTP, HTTP, DHCP, DDNS WEB BROWSER Internet Explorer 5.
