Technical Specifications
Surface Preparation
To ensure proper adhesion all surfaces should be sound, clean,
dull and dry. Remove loose paint. Wash with a mild, non-
abrasive, non-oily cleanser and water. Rinse completely, let dry.
Fill cracks and holes with patching/spackling paste and sand
smooth. Remove sanding dust with a damp cloth before
application.
Drywall: Wipe with a damp cloth to remove dust. Allow to dry.
Fill cracks & holes with spackling compound and sand smooth.
Joint compound must be cured and sanded smooth. Remove all
sanding dust.
Plaster: All new surfaces must be hard and cured according to the
supplier’s recommendations—usually at least 30 days. Treat
textured, soft, porous, or powdery plaster with a solution of 1
pint household vinegar to 1 gallon of water. Repeat until the
surface is hard, rinse with water and allow to dry.
Masonry: Allow new masonry to cure at least 30 days. Surface
must have a pH less than 9. Clean old masonry with a wire bristle
brush to remove all loose concrete and efflorescence. Rinse
thoroughly and allow to dry. Fill rough surfaces, if desired, with
block filler.
Wood: Sand any exposed wood to a fresh smooth surface. Patch
all holes and imperfections with a wood filler or putty and sand
smooth. Remove all sanding dust.
Aluminum and Galvanized Metal: Wash with appropriate
cleaner to remove any oil, grease, or surfaces contamination
using a water-based cleaner-degreaser. Remove all corrosion
with sandpaper, steel wool, or other abrading methods. Wipe
with a damp cloth.
Caulking: Fill gaps between walls, ceilings, crown moldings, and
other trim with latex or siliconized latex caulk after priming the
surface.
Mildew: Remove mildew before painting by washing with a
solution of 1 part liquid bleach and 3 parts water. Apply the
solution and scrub the mildewed area. Allow the solution to
remain on the mildewed area for 10 minutes. Rinse thoroughly
with water and allow surface to dry before painting. Wear
protective eyewear, waterproof gloves, and protective clothing.
Quickly wash off any of the mixture that comes in contact with
your skin. DO NOT ADD DETERGENTS OR AMMONIA TO THE
BLEACH/WATER SOLUTION.
WARNING! Removal of old paint by sanding, scraping or other
means may generate dust or fumes that contain lead. Exposure
to lead dust or fumes may cause brain damage or other adverse
health effects, especially in children or pregnant women.
Controlling exposure to lead or other hazardous substances
requires the use of proper protective equipment, such as a
properly fitted respirator (NIOSH approved) and proper
containment and cleanup. For more information, call the
National Lead Information Center at 1-800-424-LEAD (In US) or
contact your local health authority.
Technical Data
Vehicle: 100% Acrylic
Finish:
Flat 0-6 units @ 85˚
Eggshell 10-20 units @ 85˚
Satin 25-35 units @ 60˚
Semi-Gloss 45-55 units @ 60˚
Flash Point: N/A
Weight Solids*:
Flat 59% ± 2%
Eggshell 60% ± 2%
Satin 55% ± 2%
Semi-Gloss 54% ± 2%
Volume Solids*:
Flat 43% ± 2%
Eggshell 46% ± 2%
Satin 42% ± 2%
Semi-Gloss 41% ± 2%
Dry Time(@77°F and 50% R.H):
To Touch: 1 hour
To Recoat: 4 hours
Weight per gallon:
Flat 11.6 lb/gal
Eggshell 11.5 lb/gal
Satin 10.8 lb/gal
Semi-Gloss 10.6 lb/gal
VOC: VOC <25 g/L - 0.42lb/gal as per 40 CFR 59.406
Spread Rate:
Smooth surface: 400 sq. ft. per gal
Rough or textured surfaces: 125-300 sq. ft. per gal
Film Thickness:
Flat @ 4 mils wet; 1.73 mils dry
Eggshell @ 4 mils wet; 1.86 mils dry
Satin @ 4 mils wet; 1.67 mils dry
Semi-Gloss @ 4 mils wet; 1.66 mils dry
Sizes: Quart, Gallon, Five Gallon
*Product data calculated on Ultra White
The information and recommendations set forth in this Product
Data Sheet are based upon tests conducted by or on behalf of
Dutch Boy Paints. Information and recommendations set forth
herein are subject to change and pertain to the product offered
at the time of publication. Consult your Dutch Boy Paint Retailer
or sales representative to obtain the most recent Product Data
Sheet.
For more information, please call 1-800-828-5669, or visit www.dutchboy.com
PLATINT