polishedpro | 2.
Table of Contents Technical Data Sheet 3 General Information 4 Recommended Tool List 5 Installation Instructions 6 Maintenance Instructions 9 Product Warranty 10
polishedpro | 2.5mm LVT Technical Data Sheet General Specifications Overall Product Thickness: Wear Layer Thickness: Product Type: Product Dimensions: Finish: Residential Warranty: Commercial Warranty: Carton Quantity - Plank: Carton Weight: 2.5 mm 20 mils (0.5 mm) Glue Down Luxury VInyl Tile (LVT) 6" x 48" Scratch-Resistant Polyurethane Lifetime 5 Years 16 Pieces (32 sq. ft.) 29.1 lbs.
polishedpro | 2.
polishedpro | 2.5mm LVT Recommended Tool List • Knee Pads • Safety Glasses • Cut-Resistant Safety Gloves • Dust Mask • HEPA-Filtered Vacuum • Oscillating Multi-Tool or Hand Saw (for door jambs) • Chalk Line • Three-Section 100 lb. Floor Roller • Appropriate Notch Trowel • Tape Measure • Utility Knife with Blades • Pencil • Speed Square • 6-foot and 1-foot Straight Edge or Level DuraDecor | P: (855) 700 - 5666 | customercare@duradecor.com | duradecor.com | revised on 06.23.
polishedpro | 2.5mm LVT Installation Instructions 1. Substrate Preparation General Substrate Guidelines Ensure the substrate is clean, dry, flat, sound and suitably prepared according to these instructions prior to installation, as manufacturer is not responsible for problems related to substrates that have not been properly prepared.
polishedpro | 2.5mm LVT Installation Instructions vinyl or linoleum, as well as existing hard surface flooring substrates, such as terrazzo, porcelain or ceramic tile. Ensure existing flooring is a single layer and is clean, dry, sound, solid and well adhered. All loose material must be removed and repaired or replaced. All grout lines and wide seams greater than 1/4-in.
polishedpro | 2.5mm LVT Installation Instructions Adhesive Application Only apply as much adhesive as can be covered within the working-time, typically to only one side of the starting line at a time. Apply the adhesive slowly and evenly to the substrate at the appropriate angle using the specified trowel notch. Avoid skips, puddles or sharp trowel turns. Allow the specified open time for the adhesive, depending on the porosity of the substrate and the site conditions.
polishedpro | 2.5mm LVT Maintenance Instructions 1. Precautions Remove all metal objects before conducting maintenance and use caution tape and/or “Wet Floor” signs to prohibit foot traffic until the floor is dry. Do not use hydrocarbons, harsh disinfectants, cleaning agents, dyes, acetone or other harsh chemicals – ensure all chemicals and materials that may come in contact with flooring surface will not stain, mar or otherwise damage the surface.
polishedpro | 2.5mm LVT Product Warranty 1. General Terms DuraDecor (“Manufacturer”) warrants that, when used properly and under normal operating conditions, the flooring products described in the Manufacturer’s catalog as PolishedPro Glue Down LVT Flooring (“Product”), a 2.5mm thick Luxury Vinyl (LVT) floor covering that includes a 0.
polishedpro | 2.5mm LVT Product Warranty 2.5. Alternatively, at the Manufacturer’s discretion, a refund of the original cost of the Product shall be used to settle all other valid claims according to the following pro-rated schedule: Residential Wear Coverage: Commercial Wear Coverage: ≤ 1-year: 100% ≤ 1-year: 100% ≤ 5-years: 70% ≤ 3-years: 70% ≤ 10-years: 50% ≤ 5-years: 30% ≤ 20-years: 30% > 20-years: 10% 2.6.
polishedpro | 2.5mm LVT Product Warranty • • • • • • • • • • Heavy static loads (> 1,500 PSI) and heavy point loads, such as foot traffic with stiletto heels, spikes or skates, dropped items, improper floor protectors and furniture feet/rests or floor protection and furniture feet/rests that do not make adequate flat contact with the floor covering.
polishedpro | 2.5mm LVT which may vary from state to state. 7. Limitation of Liability The aggregate cumulative total liability of Manufacturer hereunder, whether for breach of warranty or contract, indemnification, tort (including negligence), or otherwise, shall not exceed the original purchase price of the nonconforming Product. Manufacturer assumes no liability for labor costs in the installation or replacement of any Product with visible and obvious (> 0.5-inch) defects.
