SunSplash Overhead Projectors

ManualsBrandsDukane ManualsProjectorProjectors

Thank you for choosing a SunSplash® Series Overhead Projector. Dukane

SunSplash Overhead Projectors are available in rugged steel or durable ABS

plastic bases and a choice of 2000, 2200, 3000/2400 or 4000/3200 lumens.

Features of each model vary and can include a closed or open head; a single,

double or triple element lens; a wide angle lens and a lamp changer.

Because operation of all units is very similar, this manual covers all models

in the Dukane SunSplash Series.

Summary of content (15 pages)

PAGE 1
Thank you for choosing a SunSplash® Series Overhead Projector. Dukane SunSplash Overhead Projectors are available in rugged steel or durable ABS plastic bases and a choice of 2000, 2200, 3000/2400 or 4000/3200 lumens. Features of each model vary and can include a closed or open head; a single, double or triple element lens; a wide angle lens and a lamp changer. Because operation of all units is very similar, this manual covers all models in the Dukane SunSplash Series.
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS When using your overhead projector, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2. Close supervision is necessary when any projector is used by or near children. Do not leave projector unattended while in use. 3. Care must be taken as burns can occur from touching hot parts. 4.
PAGE 3
TABLE OF CONTENTS Page SPECIFICATIONS .................................................................. 1 ELECTRICAL SAFETY GROUNDING INSTRUCTIONS ........................ 1 INDEX OF FUNCTIONAL PARTS ................................................ 2 SETUP/ASSEMBLY................................................................. 3 OPERATION ......................................................................... 4 CLEANING ...........................................................................
PAGE 4
SPECIFICATIONS Following are features common to all SunSplash Series Overhead Projectors: Focusing ... Rack and Pinion Focusing for Precise Image Adjustment Dimensions .............. 13" (W) x 15" (D) x 36" (H) or 38" (H) Max. Mounting Holes ........................... For Roll Film Feed Attachment Aperture ............................................................ 10.5" x 10.5" Head Elevation .............................................. Up to 30 Degrees Power ...........................................
PAGE 5
INDEX OF FUNCTIONAL PARTS A number of terms are used frequently in this instruction booklet. The OVERHEAD PROJECTOR will be easier to operate if you become familiar with the terms for the functional parts listed below: 1 2 7 8 3 4 9 PRIM 5 1. 2. 3. 4. 5. ARY LAM P RES ERV 6 E OPEN HEAD MAST FOCUS KNOB STAGE STAGE OPENING LATCH TABS 6. 7. 8. 9.
PAGE 6
SETUP/ASSEMBLY In order to protect the optical head during shipment, it and the mast have been packed apart from the base. 1. Remove the optical head/mast assembly and base from the shipping carton. 2. On plastic models, depress stage opening latch tabs on front of the stage and lift off stage (Step 1). Place stage aside. 3. Find the Allen head screw and the Allen wrench. (On plastic base models, find the Allen head screw, washer, wing nut and Allen wrench). 4.
PAGE 7
OPERATION Place the projector on a firm level surface at a convenient operating height. Be sure vent areas of unit are not blocked. Plug the power cord into a 120V, 60 Hz AC outlet. Move power switch to ON position. Place a transparency on the stage and turn focus knob until image is in focus. Image elevation is adjusted by moving optical head up or down. Models equipped with a lamp changer system allow change of lamp by sliding a lever.
PAGE 8
SUNSPLASH SERIES OHP SELECTION CHART 5 MODEL SP2123 SP2223 SP2125 BRIGHTNESS 2200 lumens 2200 lumens 2200 lumens LENS SYSTEM Open, single element with wide angle Open, single element with wide angle Open, single element SP2225 SP2226 SP2127 SP2128 SP2227 SP2133 SP2134 SP2233 SP2234 SP3123 SP3127 SP3128 SP3134 SP4123 SP4223 SP4125 SP4225 SP4127 SP4128 SP4233 SP4134 SP4234 SP4136 SP4236 2200 lumens 2200 lumens 2000 lumens 2000 lumens 2000 lumens 2000 lumens 2000 lumens 2000 lumens 2000 lumens 3000/2400
PAGE 9
LAMP REPLACEMENT Lamp in projector: SP2xxx — 2000 lumen, uses a 360 watt EYB lamp, Dukane Part Number 456-186. SP4xxx — 4000 lumen, uses a 410 watt FXL lamp, Dukane Part Number 456-192. SP3xxx — 3000 lumen, uses a 360 watt ENX lamp, Dukane Part Number 458-188. WARNING Lamp and adjacent metal parts are hot. Allow lamp to cool before replacing. Glass components may shatter. Handle carefully. Lamp replacement, SP2xxx units: 1.
PAGE 10
FOR 2000 LUMEN MODELS — STEP 2 — Carefully pull out bulb. Lamp replacement, SP4xxx and SP3xxx units: 1. Open unit stage by depressing the latch tabs on front of stage and lifting (Step 1). Remove the stage. 2. Pull up retainer clip wires and rotate lamp cover into open position (Step 2). FOR 3000 & 4000 LUMEN MODELS — STEP 1 — Open stage. STEP 2 — Pull up retainer clip and rotate open the lamp cover.
PAGE 11
FOR 3000 & 4000 LUMEN MODELS — 3. Squeeze the lamp retainer clip to free lamp. Carefully pull up the used lamp. Take caution since it may be hot. Allow time to cool (Step 3). 4. Place new lamp in socket. Push down until firmly seated. Avoid skin contact. Oil from skin can cause discoloration of the lamp capsule or reflector. Hold lamp with a STEP 3 — cloth, tissue or gloved hand. Open lamp retainer clip and pull out the lamp. 5. Engage the lamp retainer clip. 6.
PAGE 12
SERVICING Shipping Information If it becomes necessary to return a unit, please use the original packing material or pack securely to insure safe shipment. Service Service and parts are available from Dukane or from an approved service station. Contact the Dukane Service Department at 1-800-676-2487 to order parts or for the nearest service station. Service manuals are also available at a nominal cost.
PAGE 13
STORAGE 1. Controls should be in OFF position. 2. Store power cord in base compartment. 3. Protect unit from dust as much as possible. FRESNEL LENS REMOVAL Should it be necessary, the Fresnel lens can be removed by pressing fresnel release latches as shown below: Information on Lamp Warranty Projection lamps are warranted by the lamp manufacturer and not by the equipment manufacturer.
PAGE 14
INTERNAL PARTS 4 3 2 2000 LUMEN MODELS 5 1 11 7 3000 & 4000 LUMEN MODELS 9 10 6 1. 2. 3. 4. 5. 6. SAFETY INTERLOCK SWITCH COOLING FAN LAMP REFLECTOR MAST LOCK SCREW LAMP 7. 8. 9. 10. 11.
PAGE 15
5 YEAR LIMITED WARRANTY This Dukane projector is warranted to the original purchaser for a period of five (5) years from the original purchase date – in normal operating conditions – against defects in material and workmanship . DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.