Camera 445 Visual Presenter User Manual [Important] To download the latest version of Quick Start Guide, multilingual user manual, software, or driver, etc., please visit http://www.dukcorp.com/audiovisual/products “Downloads” Dukane Audio Visual, 2900 Dukane Drive St. Charles, IL 60174 866.280.4298 Fax: 630.584.5156 http://www.dukcorp.
Contents Copyright Information............................................................................................3 Chapter 1 Precautions ........................................................................................4 Chapter 2 Package Content ...............................................................................6 Chapter 3 Product Overview .............................................................................7 3.1 Relative position of the presenter and 445 .........
7.16 I would like to resume the factory default setting (Factory Reset) .......23 7.17 I would like to reduce the image noise (Noise Reduction) ...................24 7.18 I would like to set / change the password (Lock Down)........................24 7.19 Using a SD card.......................................................................................25 7.20 Computer-related functions ....................................................................25 7.20.
Copyright Information Copyrights © Dukane Co. All rights reserved. Dukane is a trademark that is currently being registered Dukane Corporation Inc. Copying, reproducing or transmitting this file is not allowed if a license is not provided by Dukane Corporation Inc. unless copying this file is for the purpose of backup after purchasing this product. In order to keep improving the product, Dukane Corporation Inc. hereby reserves the right to make changes to product specifications without prior notice.
Chapter 1 Precautions Always follow these safety instructions when setting up and using the visual presenter: 1. Do not place visual presenter in tilted position. 2. Do not place the visual presenter on an unstable trolley, stand or table. 3. Do not use the visual presenter near water or source of heat. 4. Use attachments only as recommended. 5. Use the type of power source indicated on the visual presenter.
EQUIPMENT. Note: This equipment has been tested and found to comply with the limits for a Class A or B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications.
Chapter 2 Package Content 445 Quick Start Guide User Manual Remote control Remote Control Holder Extender Adapter VGA Cable USB Cable C-Video Cable Power Cord Microscope Adapter Base Installation Guide Appearance may vary with country/region.
Chapter 3 Product Overview 8. Gooseneck 7. AF button 4. LED indicator 1. Lamp 3. Control panel 2. Remote sensor 9. Built-in Microphone kkkkkkk 5. Lens 6.
3.1 Relative position of the presenter and 445 445 Document Presenter 3.2 Recommend distance * About 470 mm distance between camera and the desktop is recommended.
3.
Chapter 4 Installation and Connections 4.1 System diagram PC Monitor Projector Monitor 机 PC Speaker (or an amplifier before connecting to the speaker) LCD TV SD Card PC Televisio n 4.2 Mounting the 445 on a desktop stand 1. Please set up the DIP Switch settings first. Refer to Chapter 5 “DIP Switch Settings” in this 445 user manual. 2. Please refer to the Base Installation Guide for installation instructions for all parts. 4.3 Connecting devices 4.3.
4.3.2 Step 2: Connecting the components Connecting to a projector Connect the VGA OUT on the 445 to the VGA IN on the projector using the VGA cable. Connecting to a monitor Use VGA cable to connect VGA PASSTHROUGH connector on 445 to the VGA IN connector on a monitor. [Note] The VGA PASSTHROUGH connector only outputs VGA IN signals. Connecting to a TV 1. Using EXTENDER adapter and C-Video cable to connect EXTENDER of 445 to a C-Video of TV. 2.
Use VGA cable to connect VGA IN connector on 445 to the VGA OUT connector on the computer Using the USB Cable Connect to USB port then install the supplied queue program. Using the EXTENDER adapter and RS232 Cable to connect EXTENDER of 445 to a RS232 of computer Connecting to speaker Speaker : Or connect to an additional amplifier before connecting to the speaker. 4.
4.5 Installing remote control holder Insert the holder over the gooseneck of the camera and push it down. 4.6 Installing driver and application queue (software) After installing the USB driver and application queue, you can use the following functions via the software: Control the 445. Capture and record images. Annotate the image, highlight important details and save it. 4.6.1 System requirements Operating System Windows XP Minimum CPU: P4 2.
1. Download the [queue X.X.X +Driver] and its user manual. Please follow the user manual of queue TM for installation and operation. Chapter 5 DIP Switch Settings You have to turn the unit OFF and back ON for the setting to take affect. 5.1 Connecting to a projector or monitor 5.1.1 SXGA 60Hz output (default values): 5.1.2 XGA 60 Hz output 5.1.3 Special mode 5.1.
5.2 Connecting to a TV 5.2.1 NTSC: America, Taiwan, Panama, Philippines, Canada, Chile, Japan, Korea and Mexico 5.2.2 PAL: Countries/regions not listed above. VGA output is not supported once C-Video output has been enabled.
Chapter 6 Control Panel/Remote Control and Setting Menu 6.1 Functions of control panel and remote control : OSD is not available at C-Video mode. [Menu] / [Rotate] / [PAN] / [Source] / [Record] / [Capture] / [Delete] / [PBP] / [Slide Show] functions are not available on the machine panel and the remote control. The below functions are listed alphabetically. Name Function Turn on and off the visual presenter.
6.2 Setting Menu Press [Menu] on the remote control or control panel to enter the setting menu; The bold underlined values in the following table are the defaults. rd 3 Level st nd 1 Level 2 Level Descriptions Adjustment Major Items Minor Items values Display Storage Focus 0~Max Use the left and right arrow keys to adjust focal length on an object Mode Normal/Slide/ Film/Microscope Use the left and right arrow keys to select the image mode.
memory. Format Yes/No Capture 1. Single 2. Continuous 3. Disable Capture Time Capture Interval 1. 1 hr 2. 2 hr 3. 4 hr 4. 8 hr 5. 24 hr 1. 5 sec 2. 10 sec 3. 30 sec 4. 1 min 5. 2 min 6. 5 min Use the left and right arrow keys to select, and then press [Enter] to format the data stored in the SD card (priority) or internal memory. Use the left and right arrow keys to select the video capture mode. (Single/Continuous/Disable) Use the left and right arrow keys to set the capture time.
8. Suomi 9. Polski 10. Italiano 11. Português 12. Svenska 13. Česky Finnish Polish Italian Portuguese Swedish Czech Use the left and right arrow keys in the language option to select the preferred language. Output Mode Lock Down Auto Erase 1. 2. 3. 4. 5. XGA SXGA UXGA 720P 1080P On/Off On/Off Based on different DIP switch settings, different output modes are provided. Refer to Chapter 5 DIP “Switch Settings” in the 4 user manual.
Chapter 7 Descriptions of major functions 7.1 I would like to switch image sources Live image is the default of image source. Press [Source] on the remote control or control panel to change: 1. Live images (default) 2. SD card (priority) or internal memory 3. Computer. 7.2 I would like to make text clearer and photos more colorful Photo is the default. You can change setting via the control panel. [Photo](default): for viewing photos or text with photos and will make the photos more colorful.
7.8 I would like to capture images 7.8.1 Setting the quality of captured images 1. 2. 3. 4. 5. Press [Menu] on the remote control or control panel to enter the setting menu. Press [] or [] to the [Setting]. Press [] to find [Image Quality]. Press [] or [] to select among [High/Medium/Low]. Press [Menu] to exit. 7.8.2 Setting continuous capture 1. Press [Menu] on the remote control or control panel to enter the setting menu 2. Press [] or [] to the [Setting] menu. 3. Press [] to find [Capture]. 4.
7.11 I would like to automatically delete the captured images whenever it is turned off (Auto Erase) 1. 2. 3. 4. 5. 6. 7. Press [Menu] on the remote control or control panel to enter the setting menu. Press [] or [] to access the [Advance] menu. Press [] or [] to [Auto Erase]. Press [] to select [On]. Press [] or [] to select [OK]. Press [Menu] to exit. It will automatically delete all captured photos when it is turned off. 7.12 I would like to record videos (Record) 7.12.
7.14.3 Activating/Stopping the slide show Images over 8 MB, cannot be played. Whilst playing, the [Rotate] function can be activated to rotate the images. Remote control: 1. Press [Slide Show] to start playing. 2. Press [Slide Show] again to stop playing. Control panel: 1. Press [Menu] to enter the setting menu. 2. Press [] or [] to access the [Storage] menu. 3. Press [] to find [Slide Show] 4. Press [Enter] to play. 5. To stop playing, repeat steps 1 to 4. 7.
7.17 I would like to reduce the image noise (Noise Reduction) This function enables visual presenter to automatically clear image noise. The noise is especially obvious when Visual presenter is connected to a DLP projector. You can use this function to improve the image quality. 1. Press [Menu] on the remote control or control panel to enter the setting menu. 2. Press [] or [] to the [Setting]. 3. Press [] to find [Noise Reduction]. 4. Press [] or [] to select [On]. 7.
7.19 Using a SD card 7.19.1 Deactivate the write protect function (SD Lock) on the card If the write protect function of the SD card is activated, you will not be able to use the Capture function, although you can still read the files in it. Adjust the Lock of the SD card to deactivate the write protect function. 7.19.2 Inserting a SD card 7.19.2.1 The screen will display [Copy to SD card] and ask if you would like to copy the files saved in the DC265 to a SD card.
7.20.2 I would like to insert a photo in MS-Word 1. Click Insert > Image > From Scanner or Camera in MS-Word. 2. Select [Visual Presenter V2] and click [Custom Insert]. 3. Click [Get Picture]. It will capture the photo of live image. 7.20.3 I would like to change the setting of Camera 445 then capture a photo in MS-Word 1. Click Insert > Image > From Scanner or Camera in MS-Word. 2. Select [Visual Presenter V2 TWAIN] and click [Custom Insert].
3. A window showing a live image (see below) will be displayed. 4. Press [Setting] to control the 445 via the Camera Settings interface. The operating procedure is the same with the remote control and control panel of the 445. Refer to 445 User Manual Chapter 6 Control Panel / Remote Control and Setting Menu. 5. Press [Setting] to capture images in MS-Word. 6. Press [Cancel] to exit. 7.20.
7.20.5 I would like to set the 445 as a PC Camera 1. Press [Menu] on the control panel to enter the setting menu. 2. Press [] or [] to the [Setting] menu. 3. Press [] to find [USB Transfer]. 4. Press [] or [] to select [Camera]. 5. A window will be displayed, showing the [Visual Presenter V2], as shown below 6. Click the [Visual Presenter V2]. 7.20.6 I would like to set the 445 as a Removable Disc 1. Press [Menu] on the control panel to enter the setting menu. 2.
Doing this will disable the Capture function. Suggest you return it to [Camera] mode after using this function. Please follow the steps below. 1. Press [Menu] on the control panel to enter the setting menu. 2. Press [] or [] to the [Setting] menu. 3. Press [] to find [USB Transfer]. 4. Press [] or [] to select [Camera]. 5. Press [Menu] to exit. Chapter 8 Connecting to Microscope 1. Mount the microscope adaptor onto the microscope. Please choose an appropriate microscope adapter.
4.2. Press the AF button on the camera head of main unit to activate the auto focus. 5. Digital Zoom 5.1. Press [MENU] to enter the setting menu. 5.2. Press [] or [] to the [Setting]. 5.3. Press [] to select [Digital Zoom]. 5.4. Press [] or [] to select [On]. 5.5. Press [Zoom +]/[Zoom -] on the remote control and control panel In microscope mode all functions are available except for the [Zoom +] / [Zoom -] / [PAN] functions on the remote control and control panel.
Chapter 9 Troubleshooting This chapter describes problems you may encounter while using 445. If you have questions, please refer to related chapters and follow all the suggested solutions. If the problem still occurred, please contact our distributors or service center. No. 1 2 3 4 5 6 Issues Solutions Boot without power Make sure you have plugged in the power cord. No image output 1. Check the power. from the 445 2. Check the connection, Refer to 445 User Manual Chapter 4 Installation and Connections 4.
