D-ILA Multimedia Projector Model 9100HC User's Manual Audio Visual Products
SAFETY PRECAUTIONS IMPORTANT INFORMATION NOTICE (For USA) Language for Manuals of Products using HID Lamps (that contains mercury) This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: http://www.eiae.org.
Safety Precaution – Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.
Safety Precaution POWER CONNECTION WARNING: Do not cut off the main plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter or consult your dealer. If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the main supply.
Caution About burning-in of the D-ILA device How to use the [SCREEN TRIGGER] terminal cable ● Do not allow the same still picture to be projected for a long time or an abnormally bright video image to be projected. Do not project video images with high-intensity or high contrast on a screen. The video image could be burnt into the D-ILA device. Use special care when projecting video games or computer program images. There is no problem with ordinary video cassette playback images.
Contents SAFETY PRECAUTIONS ............................................ 2 Caution ........................................................................ 5 Accessories ................................................................ 6 Controls and Features ............................................... 7 Front Side/ Top Surface/ Left Side ......................................... 7 Rear Side/ Right Side/ Bottom Surface .................................. 8 Connector Panel .................................
Controls and Features Front Side/ Top Surface/ Left Side p Zoom Ring 9 Focus Ring 1 Control Panel 8 Remote Sensor (Front) 2 AC Power Input 7 Air Inlet 4 Foot Lever Terminal 3 Carrying Handle (for front adjustable foot) 6 Lens Cap 5 Lens 4 Foot Lever (for front adjustable foot) Using the Carrying Handle 7 Air Inlets (on the front, right, and bottom side of 1 Control Panel For details, See ‘Control Panel on the Projector’.
Controls and Features Rear Side/ Right Side/ Bottom Surface t Remote Sensor (Rear) q Connector Panel r Exhaust Vent Bottom Surface w Speaker y Front Adjustable Foot 7 Air Inlet e Lamp Cover 7 Air Inlet u Filter i Rear Fixed Foot Blocked as it is not in use. Opening it forcibly will cause damage to the machine. q Connector Panel t Remote Sensor (Rear) For details, refer to ‘Connector Panel’. (☞ page 9) w Speaker Built-in speaker located here.
Controls and Features Connector Panel 1 [PC2] Input Terminal R PR/CR GY 3 [PC3] Input Terminal 2 [PC1] Input Terminal B PB/CB H/CS V DVI PC3 PC1 PC2 SCREEN TRIGGER AUDIO IN REMOTE 4 [SCREEN RS-232C OUT RS-232C IN CONTROL 8 [Y/C] Input 6 [REMOTE] TRIGGER] Terminal Terminal Terminal 5 [AUDIO IN] 7 [CONTROL RS232C 9 [VIDEO] Input IN/OUT] Terminal Terminal 1 [PC2] Input terminal (BNC x 5) This is an input terminal for component signals (Y, CB, CR) or DTV-format (Y, PB, PR) signals.
Controls and Features Control Panel on the Projector 1 [STAND BY] indicator 8 [TEMP] indicator 9 [LAMP] indicator p [VIDEO] button q [PC] button w [H-KEYSTONE] button STAND BY LAMP TEMP PC VIDEO OPERATE 2 [OPERATE] indicator 3 [OPERATE] button V-KEYSTONE H-KEYSTONE e [V-KEYSTONE] button 4 [VOL.] (volume) button VOL.
Controls and Features Control Panel on the Projector 1 [STAND BY] Indicator Light on : In stand by mode. Blinking : In cool down mode. 2 [OPERATE] Indicator Light on : During projection. 3 [OPERATE] button When this projector is in standby mode, pressing this button for more than 1 second will turn the projector on and cause the [OPERATE] indicator to light up. Press it one second or more again, and the projector goes into the cool down mode and finally into stand by mode.
Controls and Features Remote Control Unit q [VIDEO] button 1 Remote Control’s signal transmitter w [PC] button 2 [OPERATE] button PC OPERATE VIDEO e [H-KEYSTONE] button 3 [SCREEN] button (Not functional on this unit.) W V-KEYSTONE H-KEYSTONE SCREEN r [V-KEYSTONE] button DIGITAL ZOOM 4 [DIGITAL ZOOM] button S FREEZE t [VOLUME] button 5 [FREEZE] button VOLUME FOCUS QUICK ALIGN. 6 [QUICK ALIGN.] (quick alignment) button y [FOCUS] button (Not functional on this unit.
Controls and Features 1 Remote Control’s signal transmitter (☞ page 18) 2 [OPERATE] button When the projector is in standby mode, pressing this button for one second or more will turn on the projector and light up the [OPERATE] indicator. Press it one second or more again and the projector will turn off, cool down and finally enter the standby mode. (☞ page 25) • The [OPERATE] button will not work for approximately 1 minute from when the light-source lamp is turned on.
Controls and Features Loading Batteries into the Remote Control Please load batteries into the remote control. If the remote control starts to work erratically, replace the batteries. 1. Open the back cover • Push the hook on the back cover lightly in the direction of the arrow and lift it up. Precautions for using batteries If batteries are used incorrectly, they may crack or leak. This could cause fire, burn, malfunction, staining or damaging of the surroundings.
Installing the Projector Precautions for Installation Please read the following properly when installing the projector. Installation Environment Precaution for Usage Please do not install or use this projector in the following places. The projector is a precision device and doing so could cause a fire or malfunction.
Installing the Projector Installing the Projector against the Screen The picture quality may deteriorate when performing KEYSTONE compensation. It is recommended to place the projector perpendicularly to the screen. 䡵 Side View 䡵 Top View • Trapezoidal-distortion can be corrected using the [KEYSTONE]* buttons on the projector. (☞ page 30) Up to approximately 10° upward and downward from the vertical line. Up to approximately 30° upward and downward from the horizontal line.
Installing the Projector Projection Distance and Screen Size • This projector uses 1.3x manual zoom lens for projection. • Although the focusable projection distance is about 1.6 m ~ 12 m, the projection distance recommendable for performance is about 2 m ~ 8 m. Install the projector within this range and adjust the screen size when the aspect ratio of the screen is 16:9. • If the KEYSTONE is adjusted, the screen becomes smaller.
Installing the Projector Effective Range and Distance of the Remote Control Unit 䡵 Using as a wireless remote control unit The operable distance of the remote control unit is about 7 m for direct reception. The remote control unit can be used by having the transmission signal reflected off a screen. In this case, please set the total distance A + B where A is the distance from projector to screen and B is the distance from screen to remote control, within 7 m.
Connecting to Various Devices Signals that can be input into the projector The following signals can be input to the projector. 䡵 Video signals (1) Response to Decoder Decoder Input terminal NTSC O O O*2 O*2 [VIDEO] [Y/C] [Y], [PB/CB], [PR/CR]*3 [G], [B], [R], [H/Cs], [V]*4 NTSC4.43 O O*1 O*2 O*2 PAL O O O*2 O*2 SECAM O ––––– O*2 O*2 *1: Responds if Y/C output is available.
Connecting to Various Devices 䡵 Allowable input signals Signal PC system PC98 PC/AT DOS/V DVI* Mac VIDEO system Video DVI* (HDCP) VESA350 PC98 VGA 60 Hz* VGA 72 Hz VGA 75 Hz VGA 85 Hz SVGA 56 Hz SVGA 60 Hz* SVGA 72 Hz SVGA 75 Hz SVGA 85 Hz XGA 43 Hz XGA 60 Hz* XGA 70 Hz XGA 75 Hz XGA 85 Hz SXGA 43 Hz SXGA 60 Hz* SXGA 75 Hz SXGA 85 Hz SXGA+60 Hz* MAC13 MAC16 MAC19 MAC21 HDTV (1035i) 60 Hz HDTV (1035i) 59 Hz 480p* 720p 60 Hz* 720p 59 Hz* 1080i 60 Hz* 1080i 59 Hz* 1080i 50 Hz 1080 30SF/30P 1080 25SF/25P
Connecting to Various Devices Connecting to Devices Before connection, be sure to turn off both the projector and the device. 䡵 Connecting to Video Devices • Thoroughly read the manual that comes with each video device. • Use the supplied AV connection cable. S-video (Y/C) cable, BNC cable and PC Audio cables are not supplied.
Connecting to Various Devices 䡵 Connecting to Computers • Thoroughly read the manuals that come with the computer used. • Prepare cables for connecting the devices. Desktop type (DOS/V, etc.) • When the [PC2] input terminal is used, “PC2(BNC)” must be selected from the “Options” menu. (☞ page 39) • When connecting an audio output terminal such as a computer sound source to the projector, connect to the [AUDIO IN] terminal using the separately available audio cable.
Connecting to Various Devices 䡵 Control from external device It is possible to control the projector with a computer by connecting the computer to the [CONTROL RS232C IN] terminal of the projector. • Please request a connection cable from us if needed. • For more information, please contact your authorized dealer.
Connecting to Various Devices Connecting the Power Cord (supplied) After all devices have been connected, connect the supplied power cord. 1. Connect the supplied power cord to the power input terminal of the projector 1 2. Insert the main plug of the supplied power cord into the wall outlet 2 Power cord (supplied) (e.g.) Cautions Against Fire and Electric Shock ● Since the power requirement of the projector is high, please insert the power plug directly into a wall outlet.
Basic Operations If projector set up is not yet complete, please read ‘Adjustments and Settings Using Menus’ on page 32 and perform the necessary settings. Basic Operation Procedures Once the basic settings are done, follow the procedures below: 1. Power On 1 Insert the power cord into the wall outlet • The [STAND BY] indicator lights up when the main power is inputted. Light on STAND BY STAND BY LAMP TEMP PC VIDEO LAMP TEMP OPERATE OPERATE 1-2 2 V-KEYSTONE H-KEYSTONE VOL.
Basic Operations 䡵 Display using the direct buttons VIDEO The direct buttons enable direct switching and operation without having to go through the menu. Input mode can be selected by pressing the [PC] button or the [VIDEO] button. When “Line display” (☞ page 39) is set to “5sec” : After changing an input , the new selection will appear on the screen for about 5 seconds.
Basic Operations 5. Adjusting the Sound Volume 䡵 To increase the volume : press [VOLUME] ª (0 ➞ 50) 䡵 To lower the volume : press [VOLUME] · (50 ➞ 0) VOLUME VOL. LAMP PC TEMP Remote control unit Projector: Control panel STAND BY OPERATE When “Menu display” (☞ page 39) is set to “15sec”, after pressing the [VOLUME] button, the sound volume display will appear on the screen for about 15 seconds. (Press [EXIT] button to immediately remove the “Audio-Vol” display.
Basic Operations Frequently used Convenient Functions PC When an image is projected onto the screen, the following operations can be performed directly without going through the menu operation. (☞ page 27 for VOLUME operation.) OPERATE VIDEO W V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM DIGITAL ZOOM HIDE FREEZE KEYSTONE QUICK ALIGN. (quick alignment) S FREEZE VOLUME FOCUS MENU QUICK ALIGN. EXIT Enlarging the Image ENTER PRESET We can zoom in while not changing the size of the projected image.
Basic Operations Turning Off Image and Sound Video images and audio output can be turned off temporarily. Press the [HIDE] button once • Images and audio output turned off. HIDE HIDE EXIT MENU Projector: Control panel Remote control unit ENTER Press the [HIDE] button again. Images and audio output turn on again PRESET HIDE Note • When the projected image input is changed, the HIDE function is cancelled and image and sound return.
Basic Operations Removing the Trapezoidal Distortion of the Image Depending on the angle of projection onto the screen, the image may get distorted in a trapezoid form sometimes. When installing the projector or screen for the first time, or when reinstalling in other rooms, etc., Keystone adjustments need to be made to remove trapezoid distortions. 1. Press [V-KEYSTONE] / to adjust the trapezoid form in the vertical direction • A “Vert.
Basic Operations Using the Quick Alignment function PC OPERATE VIDEO The Quick Alignment function automatically adjusts (sets) the screen settings of the image input from the [PC1] or [PC2] input terminal. • This can only be performed with the remote control. W DIGITAL ZOOM V-KEYSTONE H-KEYSTONE SCREEN S FREEZE VOLUME FOCUS QUICK ALIGN. MENU EXIT ENTER PRESET HIDE Press the [QUICK ALIGN.] (Quick Alignment) button. • During automatic alignment, “QUICK ALIGN...
Adjustments and Settings Using Menus The menus displayed on the screen are used to setup the projector and perform adjustments. The Menu Structure The menus of the projector have the following structure. When video input is selected Submenu Main menu Image adj. Set up Logo Options A Language Information 12 12 12 12 Contrast Brightness Color Tint Sharpness Color temp. Reset Image adj. Set up R GB 1 Set up Logo Options A Language User A Language ENTER Information 2 “Color temp.
Adjustments and Settings Using Menus When PC input is selected Main menu Image adj. Set up Logo Options A Language Information Submenu 12 12 12 12 Contrast Brightness Color Tint Sharpness Color temp. Reset Image adj. Set up R GB 1 Set up R GB Logo Options A Language User A Language ENTER Information 2 “Color temp.” menu ENTER Position Tracking Phase Resize Clamp Sync level HIGH Options ENTER 1 Main: “Image adj.” menu Image adj. Logo 6500 Color temp. RED GREEN BLUE Image adj.
Adjustments and Settings Using Menus When no image signal is inputted Main menu Image adj. Set up ENTER Position Auto Deinterlace 1080i HDTV R GB A Logo Submenu Aspect ratio Options Decoder Language Phase OFF 1035i sF ENTER ENTER 12 Image adj. Information Set up 3 Main: “Set up” menu (When video input is selected) Image adj. Set up R GB Logo Options A Language R GB A Menu pos. Logo Horiz.disp.pos. 12 Options Vert.disp.pos. 12 Language Horiz.DIST pos.
Adjustments and Settings Using Menus The Menu Operation Buttons The menus are accessed and operated using the following buttons on the projector/remote control: Button Function Main unit Remote control unit MENU MENU Displays the main menu on the screen. • When the main menu is displayed, press to exit the menu mode. STAND BY LAMP TEMP PC VIDEO OPERATE ENTER V-KEYSTONE H-KEYSTONE Confirm the selected item on main menu.
Adjustments and Settings Using Menus The Procedure for Menu Operation 1. Press the [MENU] button The main menu is displayed on the screen. Image adj. Set up Logo Options Language A Information Contrast Brightness Color Tint Sharpness Color temp. Reset The icon of the selected menu item will be highlighted. 12 12 12 12 1 The menu item currently selected is displayed. ENTER ENTER E.g. Main menu when video input is selected: “Image adj.
Adjustment and Setting Using Menus 3 “Set up” menu The Menu Configuration Item values shown in { } are initial values set at manufacture. • Press [ENTER], [EXIT] or the right cursor button ( ) to operate a menu while it is displayed. • The menu items corresponding to an item currently selected is displayed on the right-hand side of the main menu. • Menu items shown differ according to whether Video input or PC input is selected or when there is no image signal inputted.
Adjustments and Settings Using Menus 8 “Logo” menu When there is no image signal inputted Adjustment item (press / ) Adjustment content Adjustment item (press / ) (press / ) Adjustment content (press / ) “Position” Adjusts the position of the image and menu display. [ Press the [ENTER] button to enter the “Position” menu 4. “Logo disp.” Sets whether to indicate the user set logo (captured image: “Logo disp.”) when the projector starts up.
Adjustments and Settings Using Menus p “Capture start” e “Options” menu (“Page 2”) The status of capture is displayed in bold. Adjustment item (press / ) “Capt. in prog. (approx. 2min)” The image is being read into the projector. During this time interval, the projector will not respond to any command signal inputted by the user. “Sleep time[min]” Sets the length of sleep time which, when lapsed, automatically puts the projector into stand-by state if no signal is inputted.
Adjustments and Settings Using Menus t “Information” menu Displays the information such as image input currently selected, other information and lamp usage time. When video input is selected “Input” Displays the image input [VIDEO], [Y/C], [PC2]) when projecting. “Switcher” Displays the selected switcher matching the specification of this projector. “0” : not being used. “1-10” : switcher number. For details, please check with your authorized dealer.
Setting “Aspect ratio” and “Resize” By setting the “Aspect ratio” and “Resize” of the projected input image, optimum image can be projected onto the screen. Setting the “Aspect ratio” Set the “Aspect ratio” when image is input from the [VIDEO], [Y/C] or [PC2] terminals. 1. Project the image onto the screen 4:3 image recorded in letterbox (black bars above and below the screen) such as in DVD software. STAND BY LAMP TEMP PC VIDEO OPERATE MENU 2 V-KEYSTONE H-KEYSTONE VOL. 2.
Setting “Aspect ratio” and “Resize” 5. Select “Zoom” with the cursor buttons (䊴 / 䊳) • Set “Aspect ratio” to “Zoom” for optimum projected image. Image adj. Aspect ratio Set up R GB 4:3 Logo 16:9 Zoom Options A Language Information 6. Press the [MENU] button to end when adjustment is com- STAND BY LAMP TEMP pleted OPERATE • The menu disappears from the screen. MENU PC 6 VIDEO V-KEYSTONE H-KEYSTONE VOL.
Setting “Aspect ratio” and “Resize” Setting the “Resize” Set the “Resize” when HDCP image is input from [PC3] terminal. 1. Project the image onto the screen 4:3 image recorded in letterbox (black bars above and below the screen) such as in DVD software. STAND BY LAMP TEMP OPERATE MENU PC 2 VIDEO 2. Press the [MENU] button • The main menu appears on the screen. V-KEYSTONE H-KEYSTONE Image adj. VOL.
Setting “Aspect ratio” and “Resize” 5. Select “Zoom” with the cursor buttons (䊴 / 䊳) • Set “Resize” to “Zoom” for optimum projected image. Image adj. Resize Set up R GB Logo 1:1 Panel Aspect Zoom Options A Language Information STAND BY LAMP TEMP 6. Press the [MENU] button to end when adjustment is com- OPERATE pleted MENU PC 6 VIDEO V-KEYSTONE H-KEYSTONE • The menu disappears from the screen. VOL.
Editing and Projecting Logo You can project your logo if you like when you start up the projector. This may come in useful during presentations, etc. 1. Project the images to be included in your logo MOTOR SHOW V-KEYSTONE H-KEYSTONE 2 Screen display VOL. 2. Press the [MENU] button EXIT MENU • The main menu appears on the screen. 3,5 ENTER 4 Image adj. Set up Logo Options A Language Information PC 1 Logo disp. Logo pos. Back color Logo delete Capture menu Image adj.
Editing and projecting logo 7. Set the menu position as required • Select “Menu pos.” with the cursor buttons (䊱 / 䊲) • Move the menu display position with the cursor buttons (䊴 / while viewing the projected image. Image adj. Capture menu Menu pos. Set up R GB 䊳) Horiz.move Logo Vert.move Options Horiz.size (-) Vert.size (-) A Language Information 12 (+) 12 (+) ENTER Capture start 8. Select “Horiz. move” with the cursor buttons (䊱 / 䊲) V-KEYSTONE H-KEYSTONE VOL.
Replacing the Lamp The light source lamp and its lamp time The light-source lamp has a service life. The life of lamps currently used for this projector is about 2000 hours. [Average lamp life: 2000 hours] When the light-source lamp approaches the end of its service life, deterioration progresses rapidly. Please install a new lamp when the accumulated lamp time exceeds 1900 hours or at least get a replacement lamp ready. Depending on the operating conditions, the lamp may have to be changed earlier.
Replacing the Lamp 3. Remove the lamp unit. Lamp unit 4. Insert the new lamp unit until it is fully in. Caution • Neither touches the glass surface of the lamp directly with your hand nor stains it. If you touch it with a bare hand, oil or other substances on your hand may adhere to the lamp, possibly preventing it from performing as specified and therefore lead to a shortened lamp life, a darkened screen, etc. 5. Close the handle, and tighten the screw. • Tighten the two screws with a ª screwdriver.
Replacing the Lamp Resetting the lamp time After installing a new lamp, reset the lamp time counter inside the projector when this is done. A new count will start. If the display of the accumulated lamp time has reached 2000 hours, the projector will not work (lamp does not light up) unless the lamp time is reset. 1. Insert the power cord into the wall outlet • The [STAND BY] indicator lights up when the main power is inputted. 2.
Cleaning and Replacing the Filter Clean the filter regularly or it may not work satisfactorily, causing damage. If the filter is extremely dirty and cannot be cleaned, or if it is damaged, replace the filter with a new one (Lower filter: LC32087-002A/ Inner filter: LC32058-002A). Otherwise, dirt may get inside the unit and appear on the screen, preventing you from enjoying the video fully.
Troubleshooting Before consulting your authorized dealer, please check the following points. Symptom Power is not supplied. Light is not emitted, or light is dim. With power on, the projector works but stops abruptly in a few minutes. Video image does not appear, or audio sound does not occur. Probable cause Corrective action Page Is the power cord disconnected? • Insert the power cord (plug) firmly.
Troubleshooting Symptom Probable cause Corrective action Page • Adjust focus with the focus ring of the lens. 26 Is the projector placed too near or too far from the screen? • Set the projector at the correct distance. 17 Are “Tracking” and “Phase” adjusted correctly? • Adjust “Tracking” and “Phase” using the menu. 37 Video image is ab- Is the “Brightness” adjusted correctly? normally dark or bright. • Adjust “Brightness” using the menu.
What to do when these messages are displayed Message Cause (Contents) No device is connected to the input terminal. The terminal is connected but no signal is output from the connected device. • The selected input mode (input terminal) name is shown above the message. [ Check the input image signal source. PC 1 No Input The frequency of the input video signal is out of range. [ Please ensure the frequency level of the input video signals is within the projector’s specifications.
What to do when these messages are displayed Message Cause (Contents) When the “Lamp time” reaches 1000 hours [ A message indicating “1000h” appears on the projected screen. • Press [EXIT] button to delete the message. 1000h EXIT When the accumulated lamp time reaches between 1900 hours to 2000 hours, “Lamp replacement” message appears on the screen each time the projector is turned on. • Press [EXIT] button to delete the message. [ Prepare a replacement lamp and install as quickly as possible.
Warning Indication 䡵 About warning indicators If something abnormal has occurred in the projector, the warning mode will be set in and the type of abnormality will be indicated by a combination of indicators displayed on the control panel as shown in the following table. The projector will then automatically stops projection and run the cooling fan for about 90 seconds. Indicator No.
Specifications 䡵 Model name/ Article name 9100HC projector 䡵 Emission method D-ILA®*1 (Reflective Active Matrix Principle) 䡵 Display panel/ size D-ILA*2 / 0.64 (1400 pixels x 788 pixels) x 3 (Total number of pixels: Approx. 3,309,600) 䡵 Projecting lens x 1.3 zoom lens (2:1 ~ 2.6:1) (Manual zooming and focusing) 䡵 Light-source lamp 250 W Ultra High Pressure Mercury lamp Rating: 250 W 䡵 Screen size Approx. type 37 ~ type 275 (with aspect ratio: 16:9) 䡵 Projection distance Approx. 1.
Specifications Dimensions (unit: mm) 䡵 Bottom 181 20 298 8.2 38.2 360 300 䡵 Top M6 (Depth 10 mm) 67.5 92.5 7 Center of lens 298 2 䡵 Front Attachment screw should be more than 6 mm but less than 10 mm in length. 䡵 Side 109 15 267 25 ~ 56 65.4 115.9 89 36.2 292 57 HX-1E_p50-61_En.
Specifications Pin arrangement 䡵 Y/C terminal 4 3 2 1 Pin number Signal name 1 GND (Y) 2 GND (C) 3 Y 4 C Pin number Signal name Pin number Signal name 1 N/C 6 N/C 2 RD 7 N/C 3 TD 8 N/C 4 N/C 9 N/C 5 GND Pin number Signal name Pin number Signal name 1 Red 9 N/C 2 Green 10 GND (SYNC) 3 Blue 11 GND 4 N/C 12 N/C 5 N/C 13 H.SYNC 6 GND (Red) 14 V.
Specifications 䡵 RS-232C external control By connecting a computer to the projector with a RS-232C cross cable (D-sub 9 pins), you can control the projector with the computer. The commands to control the projector and the response data format against the received commands are explained here. For details, please consult the authorized dealer where you purchased your projector. 1. Communication Specifications The communication specifications are as follows.
Specifications 3) Special parameters Input switching parameters Character Hex. Meaning 0 30 Y/C 1 31 VIDEO 3 33 PC1 4 34 PC2 5 35 PC3 Operation mode parameters Character Hex. Meaning 0000 30h 30h 30h 30h Stand-by mode 0001 30h 30h 30h 31h Power-on mode 0002 30h 30h 30h 32h Cool-down mode 0004 30h 30h 30h 34h Emergency mode 3.
DUKANE CORPORATION TWO-YEAR LIMITED WARRANTY This Dukane projector is warranted to the original purchaser for a period of two (2) years from the original purchase date – in normal operating conditions – against defects in material and workmanship . DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Audio Visual Products Audio Visual Products 2900 Dukane Drive St. Charles, IL 60174-3395 E-mail: avsales@dukcorp.
