INSTRUCTIONS PROJECTOR ENGLISH ImagePro 9015 1
Thank you for purchasing this projector. Before using it, read and follow all instructions carefully to take full advantage of the projector's capabilities. SAFETY PRECAUTIONS IMPORTANT INFORMATION WARNING : TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION : To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel. This projector is equipped with a 3-blade grounding-type plug to satisfy FCC rule.
– This product should be operated only with the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. – The product should be placed more than one foot away from heat sources such as radiators, heat registers, stoves, and other products (including amplifiers) that produce heat. – This product is equipped with a three-wire plug. This plug will fit only into a grounded power outlet.
Contents SAFETY PRECAUTIONS ........................... 2 Operating the Setting Menu ................... 31 Accessories ............................................... 5 Making Basic Settings ......................................... 31 Controls and Features .............................. 6 Front Side / Top Surface / Right Side .................... 6 Left-hand side ....................................................... 7 Bottom Surface .....................................................
Accessories The following accessories are included with this projector. Check for them; if any item is missing, please contact your dealer. Personal computer connection cable [approx. 2 m (6.56 ft)] (D-sub, 3-row 15 pin) Conversion adapter for Mac (for Macintosh) AAA/R03-size dry cell battery (×2) (for checking operation) AV connection cable [approx. 1.5 m (4.92 ft)] Power code [approx. 2.5 m (8.2 ft)] Audio cable [approx. 3 m (9.84 ft)] (3.5 mm dia.
Controls and Features Front Side / Top Surface / Right Side G IN T R E T T E S U P M O C ID V O E C Y P N E G M E T R E M E P R E P T A D N A T S Y B O E L M A K IC N U IG QL A + 3 - 2 1 9 2 8 7 6 5 4 3 4 Adjustable foot (for adjusting upper/lower angles) 1 Control panel For details, refer to “Control Panel” (page 9). It is adjusted to be level when shipped from the factory. Turning to extend the foot allows adjustment up to + 7°.
Controls and Features (cont.) Left-hand side p q w e This is the power input terminal where the supplied power cord is connected. For details, refer to page 24. q MAIN POWER switch This is the main power switch. When it is turned on, the projector goes into stand-by state, and the STAND BY indicator on the control panel comes on. ON [ ❙ ]: The main power turns on. ‡]: The main power turns off.
Controls and Features (cont.) Bottom Surface r t y u r Air intake area (filter) Air is taken in through this area to cool the light-source lamp. If this area is blocked or if something that obstructs taking in or exhausting air is placed around the projector, heat may build up inside and could cause a fire. For details, refer to “Precautions for Installation” on page 15. CAUTIONS • Be careful as paper, cloth or soft cushion could be drawn in if placed nearby.
Controls and Features (cont.) Control Panel STAND BY 1 4 Lamp indicator ON 2 OPERATE 3 LAMP 4 TEMP 5 EMERGENCY 6 VIDEO 7 COMPUTER 8 SETTING 9 : After the light-source lamp has been used for more than approx. 900 hours. Blinking : Replace the lamp. Refer to “Replacing the LightSource Lamp” on page 48. 5 TEMP indicator ON: The temperature inside the projector has abnormally risen.
Controls and Features (cont.) Control Panel (Cont.) 1 STAND BY 2 OPERATE 3 LAMP 4 TEMP 5 EMERGENCY 6 VIDEO 7 COMPUTER 8 SETTING 9 p QUICK ALIGN. button While a menu screen is shown, use this button to adjust the values for the item selected. When no menu is shown, the quick alignment function works. • When a menu is shown + 3 button: The value for the selected item increases. – 2 button: The value for the selected item decreases.
Controls and Features (cont.) Connector Panel w 1 2 Y/C VIDEO AUDIO q PC p AUDIO AUDIO R 9 G H/CS B V L Y R PB/B-Y 3 PR/R-Y 4 COMPUTER OUT REMOTE AUDIO OUT 6 5 RS-232C 7 1 Y/C (S video) input terminal (Mini DIN 4 pin) Connect this terminal to the S video output terminal of a video deck, etc. 2 VIDEO (composite video) input terminal (BNC) Connect this terminal to the composite video output terminal of a video deck, etc.
Controls and Features (cont.) Connector Panel (Cont.) w 1 2 Y/C VIDEO AUDIO q PC p AUDIO AUDIO R 9 G H/CS B V L Y R PB/B-Y 3 PR/R-Y 4 COMPUTER OUT REMOTE AUDIO OUT 6 5 RS-232C 8 7 9 COMPUTER IN (computer input) -2 terminal (BNC) These are input terminals for analog RGB signals, vertical sync (V) signals, and horizontal sync (H) signals / composite signals(Cs). Devices which have analog RGB signal output terminals can be connected.
Controls and Features (Cont.) Remote Control Unit 1 2 OPERATE e COMPUTER VIDEO T VOL. ZOOM FOCUS W PAGE BACK q MENU/ENTER 9 QUICK ALIGN. 1 Remote control’s signal transmitter 2 COMPUTER button Use this button to select the devices connected to the projector’s COMPUTER IN (computer input) -1 and -2 input terminals.
Controls and Features (cont.) Installing Batteries Install batteries in the remote control. If the remote control has started to work erratically, replace the batteries. 1 Open the back cover. While pushing on the back cover, slide it in the direction of the arrow. 2 Install the batteries. Place the two batteries (AAA/R03-size) supplied in the remote control as illustrated below. 3 Close the back cover. Slide the back cover in the direction of the arrow until a click is heard.
Installing the Projector Precautions for Installation CAUTION Do not install the projector in the following places : • There is much water, humidity or dust. • The projector may be subjected to oil smoke or cigarette smoke. • On a soft surface such as a carpet or cushion. • The projector may be subjected to direct sunlight. • Temperature is high or humidity is low.
Installing the Projector (Cont.) Projection Distance and Screen Size ■ The projector’s projection lens is a zoom lens of about 1.5 x. The screen size at the maximum enlargement is 1.5 times that of the minimum size. ■ The projection distance that can be focused is 2.5 to 20 m. Install the projector within this range.
Installing the Projector (Cont.) Relationship between Projection Distances and Projection Screen Sizes ■ For 4 : 3 aspect ratio screens Projection distance 8.2 ft (2.5 m) Projection screen size (diagonal length) Minimum projection screen size (Tele end) Maximum projection screen size (Wide end) 42” (approx. 107 cm) 63” (approx. 160 cm) 9.84 ft (3.0 m) 51” (approx. 130 cm) 76” (approx. 193 cm) 13.12 ft (4.0 m) 68” (approx. 173 cm) 102” (approx. 259 cm) 16.4 ft (5.0 m) 86” (approx.
Installing the Projector (Cont.) Effective Range and Distance of the Remote Control Unit The operable distance of the remote control unit is about 10 m (32.8 ft) for direct reception. The remote control can be used by having it reflected on the screen, etc. When you use the remote control by reflecting it at the screen, the total distance of A + B should be about 10 m (32.8 ft) or less. The operable angles of the remote control unit is 50° right to left, and 15° up and down.
Connecting to Various Devices * Before connection, be sure to turn off the projector and connected devices. * Read the manual which comes with each device thoroughly. Signals that Can Be Input to the Projector The following signals can be input to the projector: ■ Video signals (1) Response to color systems Color system Input terminal NTSC NTSC4.
Connecting to Various Devices (Cont.) Connecting to Video Devices Before connection, be sure to turn off both the projector and video device. • Read the manual which comes with each video device thoroughly. • Use the supplied AV connection cable. An AV connection cable with an S video terminal is not supplied.
Connecting to Various Devices (Cont.) Connecting to Other Devices Before connection, be sure to turn off both the projector and other devices to be connected. • Read the manual thoroughly which comes with the device to be connected. • Speakers with a built-in amplifier and game devices can be connected. Use the AV connection cable and audio cable supplied, or the cable supplied with a game device.
Connecting to Various Devices (Cont.) Connecting to Computer Devices Before connection, be sure to turn off both the projector and computer devices. • Read the manual which comes with each device thoroughly. ■ Connection to an IBM PC or IBM-compatible computer • Use the supplied computer connection cable. Also, prepare cables required for connecting the devices connected.
Connecting to Various Devices (Cont.) Connecting to Computer Devices (Cont.) Before connection, be sure to turn off both the projector and computer devices. • Read the manual which comes with each device thoroughly. ■ Connection to Macintosh • Use the supplied Personal computer connection cable and the supplied conversion adapter for Mac. • When connecting an audio output terminal such as a computer sound source to the projector, connect to the AUDIO terminal using the supplied audio cable.
Connecting to Various Devices (Cont.) Connecting the Power Cord (Supplied) After all devices have finished being connected, connect the projector’s power cord. At this time, do not turn on the MAIN POWER switch yet. 1 Insert the supplied power cord into the power input terminal (AC IN ~) of the projector. 1 AC IN ~ 2 Insert the plug of the supplied power cord into a wall outlet.
Connecting to Various Devices (Cont.) When Turning On the Devices Connected to the Projector Turn on the switches of the projector and the devices connected in the following order. Skip over unconnected devices if there is any. Power switch of the monitor of the computer which provides input to the projector ▼ Peripheral devices of the computer which provides input to the projector (Hard disk, magneto optical disk, scanner, etc.
Basic Operations ■ Projector’s buttons The following describes the basic procedure for normal use of the projector. 1. Turning on the Power STAND BY indicator STAND BY OPERATE indicator 1 Turn on the MAIN POWER switch. OPERATE button OPERATE 2, 1 LAMP TEMP ON [ ❙ ]:The main power turns on and the STAND BY indicator comes on. Projector’s indicator MAIN POWER switch EMERGENCY STAND BY 1, 2 VIDEO (ON) COMPUTER 2 Press the OPERATE button.
Basic Operations (Cont.) ■ Projector’s buttons 2. Select the video input to be projected STAND BY ■ Press the VIDEO button or the COMPUTER button to switch the input. • Each time you press either button, the selected input changes as follows. ■ When you press VIDEO: OPERATE LAMP Y/C Y,PB/B-Y,PR/R-Y VIDEO TEMP EMERGENCY ■ When you press COMPUTER: VIDEO button VIDEO COMPUTER 1 COMPUTER button COMPUTER Remote control unit SETTING +3 QUICK ALIGN.
Basic Operations (Cont.) ■ Remote control unit 4. Adjust focus ■ Adjust focus with the remote control’s FOCUS (+/–) buttons. OPERATE ■ To focus on farther points: Press the FOCUS (+) button. ■ To focus on nearer points: Press the FOCUS (–) button. COMPUTER VIDEO T VOL. ZOOM FOCUS W PAGE BACK MENU/ENTER FOCUS VOL. (+/–) buttons PRESET QUICK ALIGN. Remote control unit FOCUS (+/–) buttons AV MUTING Note • Focus adjustment can also be made on the setting menu.
Basic Operations (Cont.) ■ Remote control unit ¶ For Operating Other Functions ■ To turn off video image and audio sound temporarily OPERATE Press the AV MUTING button. ■ Press once: Video image and audio sound turn off (do not come out). ■ Press again: Video image and audio sound come out again. COMPUTER VIDEO T VOL. ZOOM Remote control unit FOCUS W MENU/ENTER PAGE BACK AV MUTING PRESET QUICK ALIGN. AV MUTING AV MUTING button QUICK ALIGN.
Basic Operations (Cont.) ■ Projector button ■ To display the SETTING menu The setting menu is used to make basic adjustments and settings (TRACKING, PHASE, H. POS., V. POS., FOCUS, ZOOM and AUDIO-VOL.) of the video picture being projected after installation (connection) or after inputs are switched. For operating the setting menu, refer to “Making Basic Settings” on page 31. STAND BY OPERATE • Press the projector’s SETTING button. The setting menu is displayed on the screen.
Operating the Setting Menu Making Basic Settings ■ Projector’s buttons Here, we make basic video adjustment and sound volume adjustment which are set up after installation (connection). EMERGENCY Notes VIDEO COMPUTER SETTING button SETTING +3 QUICK ALIGN. QUICK ALIGN. buttons -2 the SETTING button of the 1 Press projector. ■ Setting menu • The setting menu is displayed on the screen. SETTING TRACKING PHASE H.POS. V.POS. FOCUS ZOOM AUDIO -VOL.
Operating the Main Menu Configuration the Main Menu (AV Input) For computer inputs, see the following page. You can adjust video quality (PICTURE), audio quality (SOUND), etc. using the menus. The menus are configured as follows: Main menu (AV inputs : During AV IN input signal) PIXEL CLOCK TRACKING PHASE : Normally, no adjustment is required. The lateral size and display area of video image are adjusted. : Normally, no adjustment is required. Flickering or dim video image is adjusted. POSITION V. POS.
Operating the Main Menu (Cont.) Configuration of the Main Menu (Computer-related input) Main menu (Computer-related inputs : During COMPUTER IN-1 or -2 input signal) PIXEL CLOCK TRACKING PHASE : The lateral size and display area of video image are adjusted. : Flickering or dim video image is adjusted. POSITION V. POS. H. POS. : The vertical position of the video image being projected is adjusted. : The horizontal position of the video image being projected is adjusted.
Operating the Main Menu (Cont.) Operating the Main Menu (Basic Operation of the Main Menu) ■ Remote control unit OPERATE MENU/ENTER button COMPUTER VIDEO For projector’s menus, the setting menu and the main menu are available. Here, we explain about the operation of the main menu. (see pages 34 to 47) For the setting menu, refer to “Making Basic Settings” on page 31. 1 Press the MENU/ENTER button. • The main menu is displayed on the screen. T VOL.
Operating the Main Menu (Cont.) Changing the Color System ■ Remote control unit OPERATE COMPUTER VIDEO MENU/ENTER button AUTO is set for the color system when the projector is shipped from the factory. Normally, use it in AUTO. If operation in AUTO is unstable such as with color not being shown, set to a dedicated color system in accordance with the color system of the signal being input. 1 Press the MENU/ENTER button. • The main menu is shown on the screen.
Operating the Main Menu (Cont.) Changing the Language Display ■ Remote control unit OPERATE COMPUTER VIDEO MENU/ENTER button ZOOM FOCUS • The main menu is shown on the screen. • The selected item (displayed in text) is shown in magenta color on the screen. W MENU/ENTER PAGE BACK 1 Press the MENU/ENTER button. “LANGUAGE” with the cursor 2 Select button 5 or ∞ . T VOL. The language in the menu display is set to English when shipped from the factory.
Operating the Main Menu (Cont.) Adjusting the Pixel Clock ■ Remote control unit OPERATE COMPUTER VIDEO MENU/ENTER button The pixel clock should be adjusted mainly for computer-related inputs. (Normally, it does not need to be adjusted for video inputs.) If a wide stripe appears on the screen, adjust the lateral size of video image and the display area (tracking adjustment) so the stripe disappears.
Operating the Main Menu (Cont.) Adjusting the Screen Position ■ Remote control unit Adjust the position of the screen if it is displaced. 1 Press the MENU/ENTER button. • The main menu appears on the screen. OPERATE COMPUTER VIDEO MENU/ENTER button • The selected item (displayed in text) is shown in magenta color on the screen. T VOL. ZOOM “POSITION” with the cursor 2 Select button 5 or ∞ . FOCUS W 3 Press the MENU/ENTER button.
Operating the Main Menu (Cont.) Adjusting Picture Quality ■ Remote control unit OPERATE COMPUTER VIDEO MENU/ENTER button ZOOM FOCUS • The main menu appears on the screen. • The selected item (displayed in text) is shown in magenta color on the screen. W MENU/ENTER PAGE BACK 1 Press the MENU/ENTER button. “PICTURE” with the cursor 2 Select button 5 or ∞ . T VOL. Adjust brightness, contrast, etc. so you have the desired screen.
Operating the Main Menu (Cont.) Adjusting Picture Quality (Cont.) ■Remote control unit adjustment 5 Make button 2 or 3. with the cursor ■ For video system input OPERATE COMPUTER VIDEO MENU/ENTER button • To adjust multiple items, repeat steps 4 and 5. • To reset all items (to factory-set adjustment values “0”), select ALL RESET with the cursor buttons and press the MENU/ ENTER button.
Operating the Main Menu (Cont.) Adjusting Picture Quality (Cont.) Adjustment item Button 2 Gets darker. (–30 ← 0 ← +30) 3 Gets brighter. (–30 → 0 → +30) 2 Gets lower. (–30 ← 0 ← +30) 3 Gets higher. (–30 → 0 → +30) 2 Gets less reddish. (–30 ← 0 ← +30) 3 Gets more reddish. (–30 → 0 → +30) 2 Gets less greenish. (–30 ← 0 ← +30) 3 Gets more greenish. (–30 → 0 → +30) 2 Gets less bluish. (–30 ← 0 ← +30) 3 Gets more bluish.
Operating the Main Menu (Cont.) Adjusting Sound Quality ■ Remote control unit Adjust the quality (treble/bass) of sound. 1 Press the MENU/ENTER button. • The main menu appears on the screen. OPERATE COMPUTER VIDEO MENU/ENTER button • The selected item (displayed in text) is shown in magenta color on the screen. T VOL. ZOOM the “SOUND” with the cursor 2 Select button 5 or ∞ . FOCUS W 3 Press the MENU/ENTER button. MENU/ENTER PAGE BACK •The submenu items of the SOUND menu appear on the screen.
Operating the Main Menu (Cont.) Setting and Adjusting Other Functions (OPTIONS) ■ Remote control unit OPERATE COMPUTER VIDEO MENU/ENTER button The following optional functions can be set (adjusted). • MENU AUTO OFF • LINE DISPLAY • RIGHT LEFT REV. • TOP BOTTOM INV. • CLAMP • RESIZE • BACK COLOR • COLOR TEMPERATURE • ASPECT CHANGE • SLEEP TIME • LAMP TIME Memo About the lamp use time The lamp use time indicates the accumulated used hours of the light-source lamp and cannot be set or adjusted.
Operating the Main Menu (Cont.) Setting and Adjusting Other Functions (OPTIONS) (Cont.) ■Remote control unit (adjust) the desired item with the 5 Set cursor button 2 or 3. • To adjust multiple items, repeat steps 4 and 5. OPERATE COMPUTER VIDEO MENU/ENTER button Adjustment item Button MENU AUTO OFF 2/3 2/3 Sets whether to show the line display (Y/C, VIDEO, etc.) at the top of the projected screen or not. (Factory setting : ON) OFF: Does not show the line display. ON : Shows the line display.
Operating the Main Menu (Cont.) Setting and Adjusting Other Functions (OPTIONS) (Cont.) ■Remote control unit Adjustment item Button BACK COLOR OPERATE COMPUTER VIDEO 2/3 MENU/ENTER button ZOOM PAGE BACK COLOR TEMP. MENU/ENTER RED MAGENTA 2/3 Sets the color temperature of the video image being projected. Make adjustment when the image becomes reddish or bluish. (Factory setting : MIDDLE) LOW : Color temperature decreases (video image becoming reddish).
Operating the Main Menu (Cont.) Changing (Setting) the Source ■ Remote control unit OPERATE MENU/ENTER button COMPUTER VIDEO T VOL. ZOOM Normally, use the source setting in AUTO. If use in AUTO is unstable such as color not appearing, the screen being disturbed or the screen being intermitted, set to the dedicated source (forced mode) in accordance with the input signal.
Operating the Main Menu (Cont.) Changing (Setting) the Source (Cont.) ■ Remote control unit the MENU/ENTER button to set 5 Press (fix) it. ■ When AUTO is selected: OPERATE COMPUTER VIDEO MENU/ENTER button ZOOM setting procedure, and the source display inputted appears. • Both line display and source display appear on the screen and disappear in five seconds. However, they do not appear if the line display is set to OFF. T VOL.
Replacing the Light-Source Lamp The light-source lamp has its service life. It is approximately 1000 hours. When the light-source lamp approaches the end of its service life, its degradation progresses rapidly. When the lamp’s used hours exceed 900 hours, the projector’s LAMP indicator comes on. Also, at the start of projection (lamp energized), the message “REPL.-LAMP” appears on the projection screen for about two minutes. Then, replace with a new light-source lamp, or arrange for a replacement lamp.
Replacing the Light-Source Lamp (Cont.) the lamp-unit screws, raise 2 Loosen the handle, and pull out the lamp Screw unit. Loosen the two screws with a flat-end screwdriver. Note • The screws are fitted so that they do not come off the lampunit. Lamp unit 2 1 3 Handle Insert the new lamp unit fully inside and fasten the screws. Fasten the two screws with a flat-end screwdriver.
Replacing the Light-source Lamp (Cont.) Resetting the Lamp Use Time After replacing with a new light-source lamp, reset the counter inside the projector. This works to reset the life calculation of the light-source lamp, allowing the used time of the new light-source lamp to be accumulated. on the MAIN POWER switch 1 Turn to go into stand-by mode. ■Projector’s button • ON [ ❙ ]: The main power turns ON and the STAND BY [MAIN POWER switch] indicator lights.
Cleaning and Replacing the Filter Clean the filter periodically. If the filter is heavily stained and does not get clean, or if it is damaged, replace the filter with a new filter (part No.: LC30208). Otherwise, dirt may get inside and appear on the screen, possibly preventing you from enjoying the video image fully. If dirt gets inside or if you need information about the filter, consult a JVCauthorized dealer where you have purchased the projector or nearest Dukane Service center.
Troubleshooting Solutions to common problems related to your projector are described here. If none of the solutions presented here solves the problem, unplug the projector and consult a Dukane-authorized dealer or service center. Symptom Probable cause Power is not supplied. • Is the power cord disconnected? • Is the main power switch turned on? Page 24 • Turn on the MAIN POWER switch.
Symptom The upper part of the video image bows or distorts. Probable cause • While computer system signal is input, isn’t a sync signal for composite sync (Cs) or G on sync being input? Corrective action • Input separate sync signals for vertical sync (V) and horizontal sync (H) signals. • Isn’t signal with much jitter or skew distortion being input to a video deck? • Input signals with little jitter or distortion. • Is the source setting correctly selected? • Set the source setting to AUTO.
Specifications Optical mechanism system • Projection method • D-ILA device • Projecting lens • Screen size • Light-source lamp 3D-ILA device, 1 lens, 3 primary color optical shutter method 0.9" measured diagonally (1365 ×1024 pixels) × 3 (Total number of pixels : 4,193,280) Electric-driven zoom of 1.5 × 42" to 300" [recommended] to 521" [maximum] measured diagonally (*with aspect ratio : 4 : 3) 420 W xenon lamp Electrical system • Color system • Resolution • Scanning frequency NTSC, NTSC4.
Specifications (Cont.) Horizontal sync/composite sync signal (H/Cs) H : 1 to 5Vp-p, high impedance (positive/negative polarity) Cs : 1 to 5Vp-p, high impedance (positive/negative polarity) Vertical sync signal (V) V : 1 to 5Vp-p, high impedance (positive/negative polarity) * Some connected devices may not correspond to composite sync (Cs) or G on sync signal. • AUDIO (For COMPUTER IN-2) 1-line, stereo mini-jack × 1 0.
Specifications (Cont.) Outside dimensions ■ Top 16-3/4 (425)*1 Unit: Inch (mm) 13-3/8 (339) 14-7/8 (375) *1: Protrusion excluded -2 QUICK ALIGN +3 SETTING COMPUTER VIDEO EMERGENCY TEMP LAMP STAND BY φ4-1/8 (φ104) 5-1/4 (133)*1 ■ Front ■ Side 6-5/8 (168) 14-1/4 (361) 1 9-1/8 (231) 1 8- /8 (205)* 2-1/4 (55.5) DTV-format signals * The following are DTV-format signals that can be input.
Specifications (Cont.) Pin assignment (Specifications for terminals) ■ Y/C terminal Pin number 4 2 3 1 Signal name 1 GND (Y) 2 GND (C) 3 Y 4 C Pin number Signal name Pin number Signal name 1 N/C 6 N/C 2 RD 7 N/C 3 TD 8 N/C 4 N/C 9 N/C 5 GND Signal name ■ RS-232C terminal 6 7 8 9 1 2 3 4 5 15 14 13 12 11 10 9 5 4 3 8 2 1 7 6 Pin number Signal name Pin number 1 Red 9 N/C 2 Green 10 GND (SYNC) 3 Blue 11 GND 4 N/C 12 N/C 5 N/C 13 H.
