Liquid Crystal Projector Model 8053 USER'S MANUAL
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 1 Liquid Crystal Projector ENGLISH USER'S MANUAL Thank you for purchasing this liquid crystal projector. WARNING • Please read the accompanying manual “SAFETY INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. NOTE • The information in this manual is subject to change without notice.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 2 FEATURES This liquid crystal projector is used to project various computer signals as well as NTSC / PAL / SECAM video signals onto a screen. Little space is required for installation and large images can easily be realized. Outstanding Brightness The UHB lamp and high-efficiency optical system assure a high level of brightness. Partial Magnification Function Interesting parts of images can be magnified for closer viewing.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 3 Part Names Speaker Zoom Knob Focus Ring Remote Control Sensor Lens Foot Adjuster Carrying Handle AC Inlet (to the Power Cord) Power Switch Foot Adjuster Ventilation Openings (Intake) Lens Cap FRONT/LEFT VIEW OF THE PROJECTOR Control Panel (Refer to P.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 4 BEFORE USE (continued) Part Names (continued) BLANK Button STANDBY/ON Button VIDEO Button K LAN LASER Button B ER N DBY/O STAN LAS RGB Button B RG Disk Pad MOUSE / RIGHT Button O VIDE Used to operate the mouse shift function and left click function. Used to click the right mouse button. KEYSTONE Button AUTO Button MENU Button O AUT MENU SELECT Button Used to click the left mouse button. RESET Button Used to click the right mouse button.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 5 BEFORE USE (continued) Install the AA batteries into the remote control transmitter. 1. Remove the battery cover. Push the knob while lifting up the battery cover. 2. Load the batteries. Make sure the plus and minus poles are correctly oriented. 3. Close the battery cover. ENGLISH Loading the Batteries 1 2 CAUTION • Use only the specified batteries with this remote control transmitter. Also, do not mix new and old batteries.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 6 INSTALLATION Installation of the Projector and Screen Refer to the drawing and table below for determining the screen size and projection distance. The projection distances shown in the table below are for full size (CP-S420:800 x 600 pixels , CP-X430:1024 x 768 pixels). a: Distance from the projector to the screen. (±10%) Table 1. Installation Reference Screen size [inches (m)] a [inches (m)] Min. Max. 40 (1.0) 60 (1.5) 62 (1.6) 94 (2.4) 82 (2.1) 123 (3.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 7 INSTALLATION (continued) ENGLISH Cabling Refer to the table below for connecting each terminal of the projector to a device. Table 2.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 8 INSTALLATION (continued) Power Connection Use the correct power cord depending on the power outlet to be used. Connect the AC inlet of the projector to the power outlet firmly by the power cord. CAUTION • Be carful in handling the power cord according to instructions of the accompanying manual "SAFETY INSTRUCTIONS" and this manual. • Connect the power cord firmly. Avoid using a loose, unsound outlet or failed contact.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 9 STANDBY/ON Button STANDBY/ ON Button BLANK STANDBY/ON LASER VIDEO POWER Indicator Zoom Knob Focus Ring RGB AUTO MENU KEYSTONE MENU SELECT RESET POSITION FREEZE Power Switch MAGNIFY PinP MUTE OFF Lens Cap Power ON 1. Check that the power cord is connected correctly. 2. Set the power switch to [ | ]. The standby mode is selected, and the POWER indicator is turned to orange. 3.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 10 OPERATIONS (continued) Basic Operation The basic operations shown in Table 3 is performed from the supplied remote control transmitter or the projector control panel. Items indicated by (*) may be used from the control panel. Table 3 . Basic Operation Item Description Select Input Signal (*) : Press the INPUT button. RGB IN 1→RGB IN 2→DVI→ VIDEO IN → S-VIDEO IN → COMPONENT VIDEO (→ RGB IN 1) Select RGB Input : Press the RGB button.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 11 OPERATIONS (continued) ENGLISH Items indicated by (*) may be used from the control panel. Table 3. Basic Operation (continued) Item Description VOLUME Volume Adjustment : Press the VOLUME MUTE Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the MUTE mode. AUTO / button. Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and horizontal size(H.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 12 OPERATIONS (continued) Setup Menu SETUP The following adjustments and settings are possible when SETUP is selected at the top of the menu. Part of the Setup menu differs between RGB input and video input. Select an item with the and buttons, and start operation. Use the Single menu to reduce menu size (see Table 3, MENU SELECT). Table 4. Setup Menu Item INPUT BRIGHT CONTRAST V POSIT H POSIT H PHASE H SIZE COLOR BAL R COLOR BAL B ASPECT IMAGE SETUP OPT.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 13 Input Menu The following functions are available when INPUT is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. The function indicated (**) are effective on video input mode only, not on RGB input mode, except in the P.IN P. window on RGB input mode. Table 5. Input Menu Item AUTO SETUP AUTO RGB VIDEO HDTV INPUT IMAGE OPT.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 14 OPERATIONS (continued) Image Menu SETUP The following adjustments and settings are available when IMAGE is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. INPUT BLANK START UP MyScreen MIRROR P. IN P. POSIT P. IN P. INPUT GAMMA IMAGE OPT. MyScreen ORIGINAL Table 6. Image Menu Item BLANK Description Select Blank Screen: Select the screen in case of the BLANK mode with the / button.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 15 Options Menu SETUP The following adjustments and settings are available when OPT. is selected on the menu. Select an item with the and buttons, and start or stop operation with the and buttons. Table 7. Options Menu Item INPUT IMAGE OPT. 16 VOLUME MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER IR REMOTE Description ↔ VOLUME Reduce MENU COLOR Select Menu Background Color: Select with the LANGUAGE Select Menu Display Language: Select with the / button.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 16 OPERATIONS (continued) No Signal Menu The same adjustments and settings are available with the Image and Options menus when the MENU button is pressed during display of the “NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE ON ***” message while no signal is received.Select an item with the and buttons, and start or stop operation with the and buttons. VOLUME BLANK START UP MIRROR MENU COLOR LANGUAGE AUTO OFF SYNC ON G WHISPER IR REMOTE 16 Table 8.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 17 Lamp HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Contact your dealer before replacing the lamp. For the optional lamp, see the item “Optional Parts” of the Table 12. Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high temperatures. WARNING A mercury lamp used in this LCD projector is made of glass and has high internal pressure.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 18 MAINTENANCE (continued) Replacing the Lamp 1. Switch the projector OFF, remove the power cord from the power outlet, and wait at least 45 minutes for the unit to cool. 2. Prepare a new lamp. 3. Check that the projector has cooled sufficiently, and gently turn it upside down. 4. Loosen the two screws as shown in the diagram, and remove the lamp cover. 5. Loosen the three screws, and gently remove the lamp while holding the grips.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 19 Air Filter Cleaning the air Filter The air filter should be cleaned as described below at intervals of approximately 100 hours. 1. Switch the projector power supply OFF, and remove the power cord from the power outlet. 2. Clean the air filter with a vacuum cleaner. Replacing the Air Filter Replace the air filter if contamination cannot be removed, or if it is damaged. 1. Remove the filter cover. 2. Remove the old filter. 3. Set the new filter and the filter cover.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 20 TROUBLESHOOTING OSD Message The messages as described below may appear on the screen at power ON. Take the appropriate measures when such messages appears. Table 9. OSD Message Message CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIME. (*1) CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIME. THE POWER WILL TURN OFF AFTER ** hr. (*1) CHANGE THE LAMP AFTER REPLACING LAMP, RESET THE LAMP TIME. THE POWER WILL TURN OFF AFTER 0 hr.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 21 Indicators Message The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the appropriate measures. Table 10. Indicators Message POWER LAMP TEMP indicator indicator indicator Contents Lights orange Turns off Turns off The Standby mode has been set. Blinks green Turns off Turns off Warming up. Please wait. Lights green Turns off Turns off ON. Normal operation possible. Blinks orange Turns off Turns off Cooling.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 22 TROUBLESHOOTING (continued) Symptom Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer. Table 11. Symptom Symptom The power is not turned on. Possible cause Remedy Page The main power switch is not turned on. Turn on the main power switch. The power cord is disconnected. Plug the power cord into an AC power outlet.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 23 Table 12. Specifications Item Product name Liquid crystal panel Specification Liquid crystal projector Panel size 2.3 cm (0.9 type) Drive system TFT active matrix Pixels CP-X430:786,432 pixels (1024 horizontal x 768 vertical) CP-S420:480,000 pixels (800 horizontal x 600 vertical) Lens Zoom lens F=1.7 ~ 2.1 f=36.8 ~ 47.8 mm Lamp 250 W UHB Speaker 1.0W+1.0W (stereo) Power supply AC100 ~ 120V, 4.5A / AC220 ~ 240V, 1.
01CP-S420/CP-X430 03.9.2 0:08 PM ページ 24 WARRANTY AND AFTER-SERVICE If a problem occurs with the equipment, first refer to the P.20 “TROUBLESHOOTING” section and run through the suggested checks. If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.
09CP-S420/CP-X430 03.9.9 2:13 PM ページ 1 TECHNICAL Dimension Diagram RGB OUT AUDIO 1 IN AUDIO IN 2 R AUDIO OUT L CONTROL USB S-VIDEO IN VIDEO IN 1 CR/PR CB/PB COMPONENT VIDEO Y RGB IN 2 DVI 266 256.5 360 62.8 112.5 49.7 108.4 Unit : mm Signal Connector Pin Assignment 1.
09CP-S420/CP-X430 03.9.9 2:13 PM ページ 2 TECHNICAL (continued) Example of computer signal Resolution H×V fH (kHz) fV (Hz) Rating Signal mode 640 × 350 37.9 85.1 VESA 640 × 400 37.9 85.1 VESA 720 × 400 37.9 85.0 VESA 640 × 480 31.5 59.9 VESA 640 × 480 35.0 66.7 640 × 480 37.9 72.8 640 × 480 37.5 75.0 640 × 480 43.
09CP-S420/CP-X430 03.9.9 2:13 PM ページ 3 TECHNICAL (continued) Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu.
09CP-S420/CP-X430 03.9.9 2:13 PM ページ 4 TECHNICAL (continued) Connection to the Mouse Control 1. PS/2, ADB or Serial Mouse (1) Turn off the projector and computer, and connect the two units with the appropriate cable. For PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult your dealer. (2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector. (3) Turn on the computer. (4) Start the mouse function.
09CP-S420/CP-X430 03.9.
09CP-S420/CP-X430 03.9.9 2:13 PM ページ 6 TECHNICAL (continued) RS-232C communication (1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and, after the computer has started up, turn on the projector power supply.
09CP-S420/CP-X430 03.9.9 2:13 PM ページ 7 TECHNICAL (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector.
09CP-S420/CP-X430 03.9.
09CP-S420/CP-X430 03.9.
09CP-S420/CP-X430 03.9.
09CP-S420/CP-X430 03.9.
09CP-S420/CP-X430 03.9.
09CP-S420/CP-X430 03.9.9 2:13 PM ページ 13 REGULATORY NOTICES FCC Statement Warning WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Audio Visual Products Dukane Corporation Audio Visual Products Division 2900 Dukane Drive St. Charles, IL 60174-3395 E-mail: avsales@dukcorp.
