Instruction manual
Table Of Contents
- Range of Applications
- Scope of Supply
- Operation
- Putting into Service
- Setting the Basic Functions
- Functions and Settings
- First Stitch after Power On
- Softstart
- Sewing Foot Lifting
- Sewing Foot Pressure Reduction
- Start Backtack
- End Backtack
- Start and End Backtack with Switch-On and Switch-Off Delay
- Start Ornamental Backtack
- End Ornamental Backtack
- Multiple Backtacking
- Catch backtacking
- Intermediate Backtack
- Backtack Suppression/Recall
- Holding Power of the Stitch Regulator Solenoid
- Reverse Motor Rotation
- Machine Run Blockage (Safety Switch)
- Thread Monitor
- Input Signals
- Parameter 195 = 0 – No Thread Monitor Function
- Parameter 195 = 1 – Model 270 / No Stop / Sewing Foot Down after Seam End
- Parameter 195 = 2 – Model 767, N291 / With Stop / Sewing Foot Up after Seam End
- Parameter 195 = 3 – Model 767, N291 / With Stop / Sewing Foot Down after Seam End
- Parameter 195 = 4 – With Thread Monitor Stitch Counting
- Needle Cooling
- High Lift for Walking Foot
- Manual High Lift for Walking Foot – Speed Limitation
- Maximum High Lift for Walking Foot by Using a Key
- High Lift for Walking Foot Operational Mode Not Stored (Pa. 138 = OFF, Pa. 184 = 0)
- High Lift for Walking Foot Operational Mode Stored (Pa. 138 = ON)
- High Lift for Walking Foot Operational Mode Not Stored with Minimum Number of Stitches (Pa. 138 = OFF, Pa. 184 = >0)
- Speed Limitation
- Switch Stitch Length
- Roller
- Thread Clamp
- Thread Trimming Operation
- Seam with Stitch Counting
- Free Seam and Seam with Light Barrier
- Light Barrier
- Needle Up/Down / Single Stitch
- F1/F2 Function Key Assignment on the V810/V820 Control Panels
- Signal Output Position 2
- Signal Output 512 Impulses per Rotation
- Actuator
- Acoustic Signal
- Master Reset
- Input and Output Function Test
- Error Displays
- Operating Elements of the V810 Control Panel
- Operating Elements of the V820 Control Panel
EFKA DA82GA3312
7
2.1 Special Accessories
Control panel Variocontrol V810 - part no. 5970153
Control panel Variocontrol V820 - part no. 5970154
Reflection light barrier module LSM001A - part no. 6100028
EFKANET interface IF232-2 - part no. 7900068
Actuating solenoid type EM1.. (for e. g. sewing foot lifting, backtacking, etc.) - see specification
“solenoids” for
available models
Extension cable for commutation transmitter, approx. 1100 mm long, complete with - part no. 1112247
plug and socket connector
Extension cable for position transmitter, approx. 1100 mm long, complete with - part no. 1100409
plug and socket connector
Extension cable for motor connection, approx. 1500 mm long - part no. 1111857
Extension cable for external actuator, approx. 750 mm long, complete with - part no. 1111845
plug and socket connector
Extension cable for external actuator, approx. 1500 mm long, complete with - part no. 1111787
plug and socket connector
5-pin plug with locking screw for the connection of another external actuator - part no. 0501278
External actuator type EB302 (softer spring) with approx. 250 mm connecting - part no. 4170012
cable and 5-pin plug with locking screw
Foot control type FB301 with one pedal for standing operation, with approx. 300 mm - part no. 4170013
connecting cable and plug
Foot control type FB302 with three pedals for standing operation, with approx. 1400 mm - part no. 4170018
connecting cable and plug
Potential equalization cord 700 mm long, LIY 2.5 mm
2
, grey, with spades - part no. 1100313
on both sides
Pulley 40 mm Ø with special belt intake and slip-off protection (use SPZ belt) - part no. 1112223
Pulley 50 mm Ø with special belt intake and slip-off protection (use SPZ belt) - part no. 1112224
Knee switch type KN3 (pushbutton) with cord of approx. 950 mm length without plug - part no. 5870013
Sewing light transformer - please indicate line
voltage and sewing
light voltage
(6,3V or 12V)
Pitman rod for foot control - available versions
on inquiry
8-pin plug with locking screw MAS 8100S - part no. 0502865
8-pin plug with locking screw MAS 8100SN - part no. 0501279
15-contact SubminD male connector with half-shell housing - part no. 1113193
37-contact SubminD male connector with half-shell housing - part no. 1112900
Note
Select the pulley such that the motor runs at approx. 4000 RPM with max. stitch number.