Instruction manual
Table Of Contents
- Range of Applications
- Scope of Supply
- Operation
- Putting into Service
- Setting the Basic Functions
- Functions and Settings
- First Stitch after Power On
- Softstart
- Sewing Foot Lifting
- Sewing Foot Pressure Reduction
- Start Backtack
- End Backtack
- Start and End Backtack with Switch-On and Switch-Off Delay
- Start Ornamental Backtack
- End Ornamental Backtack
- Multiple Backtacking
- Catch backtacking
- Intermediate Backtack
- Backtack Suppression/Recall
- Holding Power of the Stitch Regulator Solenoid
- Reverse Motor Rotation
- Machine Run Blockage (Safety Switch)
- Thread Monitor
- Input Signals
- Parameter 195 = 0 – No Thread Monitor Function
- Parameter 195 = 1 – Model 270 / No Stop / Sewing Foot Down after Seam End
- Parameter 195 = 2 – Model 767, N291 / With Stop / Sewing Foot Up after Seam End
- Parameter 195 = 3 – Model 767, N291 / With Stop / Sewing Foot Down after Seam End
- Parameter 195 = 4 – With Thread Monitor Stitch Counting
- Needle Cooling
- High Lift for Walking Foot
- Manual High Lift for Walking Foot – Speed Limitation
- Maximum High Lift for Walking Foot by Using a Key
- High Lift for Walking Foot Operational Mode Not Stored (Pa. 138 = OFF, Pa. 184 = 0)
- High Lift for Walking Foot Operational Mode Stored (Pa. 138 = ON)
- High Lift for Walking Foot Operational Mode Not Stored with Minimum Number of Stitches (Pa. 138 = OFF, Pa. 184 = >0)
- Speed Limitation
- Switch Stitch Length
- Roller
- Thread Clamp
- Thread Trimming Operation
- Seam with Stitch Counting
- Free Seam and Seam with Light Barrier
- Light Barrier
- Needle Up/Down / Single Stitch
- F1/F2 Function Key Assignment on the V810/V820 Control Panels
- Signal Output Position 2
- Signal Output 512 Impulses per Rotation
- Actuator
- Acoustic Signal
- Master Reset
- Input and Output Function Test
- Error Displays
- Operating Elements of the V810 Control Panel
- Operating Elements of the V820 Control Panel
EFKA DA82GA3312
27
6 Functions and Settings
6.1 First Stitch after Power On
Functions Parameter
1 stitch at positioning speed after power On (Sn1) 231
For the protection of the sewing machine and if parameter 231 is On, the first stitch after power On will be performed at
positioning speed n1, independently of the pedal position and the softstart function.
6.2 Softstart
Functions Parameter
Softstart On/Off (SSt) 134
Functions:
after power on
at the beginning of a new seam
speed pedal controlled and limited to (n6)
lower speed of a parallel function prevailing (e. g. start backtack, stitch counting)
stitch counting synchronized to position 1
suspension with pedal in position 0 (neutral) / interruption by full heelback (position -2)
When using the V820 control panel, direct access is possible by means of the function key (key 9)!
Functions Parameter
Softstart On/Off (-F-) 008 = 1
6.2.1 Softstart Speed
Function with or without control panel Parameter
Softstart speed (n6) 115
6.2.2 Softstart Stitches
Functions Parameter
Number of softstart stitches (SSc) 100
6.3 Sewing Foot Lifting
Functions V810 V820
Sewing foot lifting at stop in the seam lefthand arrow above key On Key 3 Key 6
(automatic)
Sewing foot lifting after thread trimming righthand arrow above key On
(automatic)
Sewing foot lifting at stop in the seam and both arrows above key On
after thread trimming (automatic)
Sewing foot lifting Off both arrows above key Off