Instruction manual
Table Of Contents
- Range of Applications
- Scope of Supply
- Operation
- Putting into Service
- Setting the Basic Functions
- Functions and Settings
- First Stitch after Power On
- Softstart
- Sewing Foot Lifting
- Sewing Foot Pressure Reduction
- Start Backtack
- End Backtack
- Start and End Backtack with Switch-On and Switch-Off Delay
- Start Ornamental Backtack
- End Ornamental Backtack
- Multiple Backtacking
- Catch backtacking
- Intermediate Backtack
- Backtack Suppression/Recall
- Holding Power of the Stitch Regulator Solenoid
- Reverse Motor Rotation
- Machine Run Blockage (Safety Switch)
- Thread Monitor
- Input Signals
- Parameter 195 = 0 – No Thread Monitor Function
- Parameter 195 = 1 – Model 270 / No Stop / Sewing Foot Down after Seam End
- Parameter 195 = 2 – Model 767, N291 / With Stop / Sewing Foot Up after Seam End
- Parameter 195 = 3 – Model 767, N291 / With Stop / Sewing Foot Down after Seam End
- Parameter 195 = 4 – With Thread Monitor Stitch Counting
- Needle Cooling
- High Lift for Walking Foot
- Manual High Lift for Walking Foot – Speed Limitation
- Maximum High Lift for Walking Foot by Using a Key
- High Lift for Walking Foot Operational Mode Not Stored (Pa. 138 = OFF, Pa. 184 = 0)
- High Lift for Walking Foot Operational Mode Stored (Pa. 138 = ON)
- High Lift for Walking Foot Operational Mode Not Stored with Minimum Number of Stitches (Pa. 138 = OFF, Pa. 184 = >0)
- Speed Limitation
- Switch Stitch Length
- Roller
- Thread Clamp
- Thread Trimming Operation
- Seam with Stitch Counting
- Free Seam and Seam with Light Barrier
- Light Barrier
- Needle Up/Down / Single Stitch
- F1/F2 Function Key Assignment on the V810/V820 Control Panels
- Signal Output Position 2
- Signal Output 512 Impulses per Rotation
- Actuator
- Acoustic Signal
- Master Reset
- Input and Output Function Test
- Error Displays
- Operating Elements of the V810 Control Panel
- Operating Elements of the V820 Control Panel
EFKA DA82GA3312
21
4 Putting into Service
Before putting the control into service, the following must be ensured, checked and/or adjusted:
The correct installation of the drive, position transmitter and accompanying devices, if necessary
If necessary, the correct adjustment of the direction of motor rotation using parameter 161
Verify using parameter 280 that the appropriate series is connected
The setting of the reference position using parameter 170
The setting of the positions using parameter 171
The correct positioning speed using parameter 110
The correct maximum speed compatible with the sewing machine using parameter 111
The setting of the remaining relevant parameters
Start sewing in order to save the set values
If the power is turned off before sewing has been started, the settings get lost!
5 Setting the Basic Functions
5.1 Direction of Motor Rotation
Functions Parameter
Direction of motor rotation (drE) 161
Parameter 161 = 0 Clockwise motor rotation
Parameter 161 = 1 Counterclockwise motor rotation (look at the motor shaft)
5.2 Selection of the Machine Series
Functions Parameter
Display of the machine series (SEL) 280
The various machine models are specified by resistors. The following resistance values (tolerance ± 1%) are provided:
Machine model = 271, N291, 8967 = 100Ω
204, 205, 221, 266, 366 = 220Ω
069, 267, 268, 269, 4180, 4280 = 680Ω
381, 382, 467, 767, 768 = 1000Ω
The special functional sequences for this machine type and the various preset values are activated depending on the resistor
identified. The machine select is displayed using parameter 280. The resistance value is displayed in Ohm directly on the
control panel.
ATTENTION
If the motor is mounted differently, e. g. at a different angle or with gear, make sure
that the value set using parameter 161 corresponds to the direction of rotation.