Instruction manual

EFKA AB221A/AB321A + AB222A/AB322A (BA)
39
Mode 20 Lockstitch Machines (Juki LU1510-7/DNU1541-7)
- Thread trimmer (FA) for programmable increments (iFA) after intermediate stop in position 1
- Thread tension release from trailing edge of slot position 2 after delay (FSE) during ON period (FSA)
- Thread wiper after stop in position 2 after delay (kd3) during ON period (kt3)
- Sewing foot lifting (see chapter "Sewing Foot Lifting")
- Backtacking (see chapter "Start Backtack" and "End Backtack")
- Signal (M5) “machine running” / Signal (M6) “machine at standstill”
Mode 21 Chainstitch Machines (Yamato Stitch Lock)
- Thread trimmer (M1) after stop in position 2 after delay (kd1) during ON period (kt1)
- Thread wiper (M3) after stop in position 2 after delay (kd3) during ON period (kt3)
- Stitch lock signal (STV) after stop in position 1 after delay (kd2) during ON period (kt2)
- Time-delayed (kdF) sewing foot lifting after standstill in position 2 (see chapter "Sewing Foot Lifting")
- Stitch condensing (M2) (see chapter "Start Stitch Condensing" and "End Stitch Condensing")
- Signal (M5) “machine running”
Mode 22 Lockstitch Machines with Thread Trimming System (e. g. Brother B-891)
- Thread trimmer for programmable increments (iFA) after intermediate stop in position 1
- Thread tension release from trailing edge of slot position 2 after delay (FSE) during ON period (FSA)
- Thread wiper for a programmable time (t6)
- Sewing foot lifting (see chapter "Sewing Foot Lifting")
- Backtacking (see chapter "Start Backtack" and "End Backtack")
- Signal “machine running”
- Switch stitch length/flip-flop at limited speed after pressing the key
Mode 23 Lockstitch Machines (Dürkopp Adler 271...275)
- Thread trimmer (M1) for programmable increments (iFA) after intermediate stop in position 1
- Thread tension release from trailing edge of slot position 2 after delay (FSE) during ON period (FSA)
- Thread wiper (M3) for a programmable time (t6)
- Sewing foot lifting (see chapter "Sewing Foot Lifting")
- Backtacking (see chapter "Start Backtack" and "End Backtack")
- Signal (M2) “machine running”
- High lift for walking foot/flip-flop (M5) at limited speed after pressing the key
Mode 24 Chainstitch Machine (Pegasus MHG-100)
- Thread trimmer (M1) after stop in position 2 after delay (kd2) during ON period (kt2)
- Thread trimmer (M2) after stop in position 2 after delay (kd1) during ON period (kt1)
- Thread wiper (M3) after stop in position 2 after delay (kd3) during ON period (kt3)
- Sewing foot lifting (see chapter "Sewing Foot Lifting")
- Signal (M7) “hemming guide”
- Signal (M8) “hemming blow 1”
- Signal (M9) “hemming blow 2”
Mode 25 Lockstitch Machines with Thread Trimming System (Juki LU2210/LU2260)
- Thread trimmer for programmable increments (iFA) after intermediate stop in position 1
- Thread tension release from trailing edge of slot position 2 after delay (FSE) during ON period (FSA)
- Thread wiper for a programmable time (t6)
- Sewing foot lifting (see chapter "Sewing Foot Lifting")
- Backtacking (see chapter "Start Backtack" and "End Backtack")
- Signal “machine running”
- High lift for walking foot/flip-flop at limited speed after pressing the key
Mode 26 Lockstitch Machines (Jentschmann). Functions as with mode 3.
Mode 27 Lockstitch Machines (ISM). Functions as with mode 0.
Mode 28 Backlatch Machines
- Chain suction (VR) On at the start of the seam during stitch count (c1) and at the seam end from light
barrier uncovered onwards during stitch count (c2)
- Chain blowing 1 (M1) after delay (kd1) during ON period (kt1) at the seam end
- Chain blowing 2 (M2) during ON period (kt2) at the seam end
- Thread clamp (M3) On at the seam end after delay (kd3) and Off after stitch count (ckL) at the start of the seam
- Thread tension release (M4) On after stitch count (SFS) at the start of the seam and Off after light barrier
uncovered at the seam end
- Lift suction head (M8) from standstill onwards after delay (Ad1) during ON period (At1)
- Suction head (M9) On from standstill onwards after delay (Ad2) during ON period (At2)
- Chain pusher (M10) On at the start of the seam after stitch count (c3) Off after stitch count (c4)
- Sewing foot lifting (see chapter "Sewing Foot Lifting")
- Signal “machine running”
Mode 29 KMF function: synchronous operation
Mode 30 Lockstitch Machines (Juki LU1521N-7) with short trimmer. Functions as with mode 20.
Mode 31 Lockstitch Machines (Brother). Functions as with mode 0.
Mode 32 Chainstitch Machines (Brother). Functions as with mode 5.