Instruction manual

PAGE - 13
Key
Parameters Function Range Pre.setting Description
HVP -20 Parameters List for DA-281 (MAC. 73)--version 1.0 N
Parameters
Code
Forward_backward_motion control Function selection.
ON：Enable the function of 【150. INE】= CW， Reverse run will be enabled while the signal ON.
OFF：Disable.
When 【230. KLC】=ON. Setting the number of stitches for the walking foot operation.
0 ： Function disable.
1 ~ 255 ：Stitches setting. Valid only (1). when 【062. HPM】=ALT. 【230. KLC】=ON。
(2). when 【062. HPM】=MON. 【230. KLC】=OFF , 【154. O1 】=KS1 ,【014. SBT】=ON by tape cutter stitches
ON ：Enable.
OFF：Disable.
ON ：Enable. When【151. INF】= F
OFF：Disable.
ON： Speed limited by【191. B3】setting.
OFF：Function disable.
Knee switch control selection.
ON：The knee switch can be activated during sewing.( Used for blind stitch machine )
OFF：The knee switch can be activated at sewing stop only.
0 : Trimming stitch forwards with wiper function.
1 : Trimming stitch backwards with wiper function.
2 : Trimming stitch forwards with thread clamp function.
3 : Trimming stitch backwards with thread clamp function.
0 : Thread clamp off (Note : NFL = sewing foot lifting)
1 : Thread clamp functions with parameters [210. FK1] , [211. FK2] setting angle. (without NFL)
2 : Preset values : fk on = 108 , fk off = 268 (degrees) (without NFL)
3 : Preset values : fk on = 108 , fk off = 268 , nfl on = 97 , nfl off = 154 (degrees) (with NFL)
4 : Preset values : fk on = 44 , fk off = 268 , nfl on = 44 , nfl off = 154 (degrees) (with NFL)
5 : NOP
6 : NOP
7 : NOP
8 : NOP
9 : NOP
10 : NOP
11 : NOP
Setting the number of stitches for the walking foot operation.
0 ：Function disable.
1 ~ 255 ：Stitches setting. Valid only (1). when 【062. HPM】=ALT. 【153. INK】=HP.【151. INF】=HP.
( INF must be connected to knee switch )
(2). when 【062. HPM】=MON. 【231. FLC】
=OFF , 【154. O1 】=KS1 ,【021. EBT】=ON or 【099. SEN】= ON
by tape cutter stitches counter.
238 SFO Full-On time setting . 0 - 990 ms 350 For solenoid pulling torque adjustment.
239 SFC Duty cycle time setting . 10 - 90％ 25 For solenoid's switching power adjustment.
ON ： anytime.
OFF：edge sensor is uncovered.
ON : Start cutter allways valid.
OFF : Start cutter is canceled .
ON ： Enable.
OFF：Disable.
Motor driver mode selection.
SK ：For Seiko machine serila.
DA ：For Standard Version & Durkopp serial.
PK ：For Pegasus Machine serial.
Forward_backward_motion control function.
235
FBM
SK,DA,PK
MTC
Manual Tape Cutter operation mode .
(Pegasus AT function)
Sensor function , If sewing machine run after
sensor covered at the start seam.
ON/OFF
243
240
Password Function
MTP Motor Driver mode Selection.
242
FTC
OFF
ON/OFF
OFFON/OFF
OFF
DA
0
2
OFF
OFF
236 SEL Machine code Subcode Select 0/1 Default Setting = 0 , Other SubCode See the Sample Setting Page.
0
To operate HP function by the knee switch.
ON/OFF
ON/OFF
Setting the number of stitches for HP function.229
228
Setting the number of stitches for HP function.
231
232
FHP
FKL 0 ~ 11
0 - 255 stitches
KNA
KHP
Thread clamp function
Related parameter :
[155.OB]=FK , [210.FK1], [211.FK2]
Knee switch control function.
234 FAR Trimming stitch forwards or backwards.
233
ON/OFF
0 - 255 stitches
ON/OFF
OFF
0
2
OFFON/OFF
0/1/2/3
OFF
230
237
241
IDC
KLC
DBA
FLC
P
O
W
E
R
..
O
N
To operate HP function by half heeling pedal.
Manual backtack with speed limitation DB3000.
＋