Instruction manual

PAGE - 2
Key
Parameters Function Range Pre.setting Description
HVP -20 Parameters List for DA-281 (MAC. 73)--version 1.0 N
Parameters
Code
Additional
15
stitches
are
added
to
the
Start
and
End
back
-
tacking
stitches
function
selection
.
(invalid
with
operation
panel)
ON：Valid.
OFF：Invalid.
0. Depends on the pedal.
1. At motor stop.
2. At trimming after .
3. At trimming after & at motor stop.
29 SB9 0-99 stitches plus on Start/End back-tacking 0 - 99 stitches 0 Additional setting stitches are added to the Start and End back-tacking stitches. (invalid with operation panel)
Added 1 stitch to the C segment of End back-tacking function selection.
ON：Valid
OFF：Invalid
Bar-tacking mode selection.
A：One shot sewing.
M：Pedal control and motor can stop at middle way.
SU：One shot sewing but motor stops at needle up by 【027. CT】 timer at end of each seam.
SD：One shot sewing but motor stops at needle down by【027. CT】 timer at end of each seam.
Valid only when the operation panel disconnected.
ON：Perform
OFF：Not perform.
33 BRC Setting stitches of Bar-tacking 0 - 99 stitches 4 One setting for all seams ,【032. BAR】 = ON valid.
34 BRN Setting turns of Bar-tacking 0 - 15 times 4 Setting the seam times of Bar-tacking ,【032. BAR】= ON valid.
35 BT5 Stitch balance for Bar-tacking 5 4 BT5=0 : Invalid,1-8 : Increase stitches of reverse seam; 9-F : Increase stitches of forward seam.
36 BT6 Stitch balance for Bar-tacking 6 6 BT6=0 : Invalid,1-8 : Increase stitches of forward seam; 9-F : Increase stitches of reverse seam.
Constant-stitch sewing mode selection.
A：One shot sewing.
M：Pedal control and motor can stop at middle way.
Valid only when the operation panel disconnected.
ON：Perform.
OFF：Not perform.
Stitches for section 1～4 of Constant-stitch
15
Stitches settin
g
of seam P1-P4. 【038. PM】 =ON valid.
Stitches for section
5
～D of Constant-stitch
0
Stitches settin
g
of seam P5-PD. 【038. PM】 = ON valid.
Wiper function selection.
ON：Enable.
OFF：Disable.
Trimmer function selection.
ON：Enable.
OFF：Disable.
Counter function mode selection.
NOP ： The counter is invalid.
U ： Count up by stitches. When count over , counter will be auto- reset.
D ： Count down by stitches. When count over , counter will be auto- reset.
US ： Count up by stitches. When count over, motor stops and the counter must be reset by the external switch S4
【152.INI】=CRS or the A key on the front panel..
DS ： Count down by stitches. When count over, motor stops and the counter must be reset by the external switch S4
【152.INI】=CRS or the A key on the front panel..
UT ： Count up by trimming. When count over , counter will be auto- reset.
DT ： Count down by trimming. When count over , counter will be auto- reset.
UTS ： Count up by trimming. When count over,
motor stops and the counter must be reset by the external switch S4【152.INI】=CRS or the A key on the front panel.
DTS ： Count down by trimming. When count over,
motor stops and the counter must be reset by the external switch S4【152.INI】=CRS or the A key on the front panel.
43 UD
Settin
g
the count 1 - 999
9
99
Count settin
g
.
(
Note: The real number = the value of【003.CN
R
】
X
【043.UD】, when 【042.CUD】= U,D,US,UD valid
44 PN Display the current count 0 - 9999 0 Display the current count of【043.UD】
45 SP Sewing speed 0 - 8000 0 Showing the current sewing speed.
Motor rotation direction ad
j
ustments.
(
Viewed from the motor shaft side
)
Connection : 【119, D
D
】
CCW ：counterclockwise.
CW ： clockwise.
P
O
W
E
R
..
O
N
31
15 stitches plus on Start/End back-tacking
(with C-60)
ON/OFF
Mode selection for foot lifting .
(with F-10 , C-200)
30
28
SB5
SMB
AFM
Mode selection for Bar-tacking
BCC
Added 1 stitch to the C segment of End back-
tacking
00/1/2/3
AA/M/SU/SD
OFFON/OFF
OFFON/OFF
0 - F
A/M
OFF
M37
Bar-tacking selectionBAR32
Mode selection for Constant-stitch sewingSMP
38
ON
OFFON/OFF
39 PS 0 - 250 stitches
Constant-stitch sewing selectionPM
ON
40 WON Wiper function selection ON/OFF
41 TM Trimmer function selection ON/OFF
NOP
46 DIR Direction of motor rotation CW/CCW CCW
42 CUD
Count mode selection
(For Bobbin Thread or Sewing Piece)
NOP/U/D/US/DS/
UT/DT/UTS/DTS