Instruction manual

PAGE - 1
Key
Parameters Function Range Pre.setting Description
1 H Maximum sewing speed 50 - 9999 spm 4800 Maximum speed adjustments
The slow start operation mode is selected. This is valid when the panel [SL] key is ON in the normal mode.
T：Slow start operation will begin when the power is turned ON or when the first toe down after thread trimming,
or the first external run signal (S0,S1) is turned ON.
A：Slow start operation will begin when the pedal is toed down or when the external run signal (S0,S1) is turned ON.
3 CNR Counter ratio selection 1 - 100 1
Setting the multiple to the value of 【042. CUD】
Connection :【042. CUD】,【159. O4】,【097. TK3】
4 N Start back-tacking speed 50 - 8000 spm 1300 Start back-tacking speed adjustments
5 V End back-tacking speed 50 - 8000 spm 1300 End back-tacking speed adjustments
6 B Bar-Tacking Speed 50 - 8000 spm 1300 Repeat bar-tacking speed adjustments
7 S Slow start speed 50 - 2000 spm 800 Slow start speed adjustments
8 SLS Stitch numbers for Slow start 0 - 99 stitches 2 Slow start stitches setting
9 A Automatic constant-stitch sewing speed 50 - 8000 spm 4800 Valid only at the auto pattern sewing or one shot signal（SH）active
Only at the last seam of pattern sewing
ON：Valid.
OFF：Invalid.
J = JUKI mode , B = BROTHER mode.
J：Active when motor stop or running
B：Active only when motor running
Start back-tacking mode selection
A：One shot sewing
M：Pedal control and motor can stop at middle way.
SU：One shot sewing but motor stops at needle up by [027.CT] timer at end of each seam.
SD：One shot sewing but motor stops at needle down by [027.CT] timer at end of each seam.
Mode selection at the end of Start back-tacking
CON：At the end of Start back-tacking ,machine continues sewing if pedal pressed or START signal on (standing
operation)
STP：At the end of Start Back-Tacking, machine stops and must re-start by pedal command.
TRM： Making the trimming cycle once the Start Back-Tacking finished. ( Mini Bar tacking )
Valid only when the operation panel disconnected.
ON：Perform
OFF：Not perform
15 SBA Setting stitches A of Start back-tacking 3
16 SBB Setting stitches B of Start back-tacking 3
17 SBN Setting turns of Start Back-tacking 0 - 4 times 2 Setting the seam times of Start back-tacking ,【014. SBT】= ON valid
18 BT1 Stitch balance for Start Back-tacking 4 BT1=0:Invalid,1-8:Increase stitches of reverse seam,9-F:Increase stitches of forward seam .
19 BT2 Stitch balance for Start Back-tacking 6 BT2=0:Invalid,1-8:Increase stitches of forward seam,9-F:Increase stitches of reverse seam .
End back-tacking mode selection.
A：One shot sewing.
SU：One shot sewing but machine stops up position by 【027. CT】 timer at the end of each seam.
SD：One shot sewing but machine stops down position by 【027. CT】 timer at the end of each seam.
Valid only when the operation panel disconnected.
ON：Perform
OFF
：Not perform
22 EBC Setting stitches C of End back-tacking 3
23 EBD Setting stitches D of End back-tacking 3
24 EBN Setting turns of End back-tacking 0 - 4 times 2 Setting the seam times of End back-tacking , 【021．EBT】 = ON valid
25 BT3 Stitch balance for End Back-tacking 3 6 BT3=0:Invalid,1-8:Increase stitches of reverse seam,9-F:Increase stitches of forward seam .
26 BT4 Stitch balance for End Back-tacking 4 3 BT4=0:Invalid,1-8:Increase stitches of forward seam,9-F:Increase stitches of reverse seam .
【012. SMS】,【020. SME】, 【031. SMB】= SU,SD setting valid.
Conner stop timer, valid only at 【012. SMS】,【020. SME】,【031. SMB】setting SU/SD.
P
O
W
E
R
..
O
N
12
13
20
14
RVM Back-tacking mode selection
EBT
Start back-tacking function selectionSBT
SMS Mode selection for Start back-tacking
Mode selection for End back-tacking
TYS
11
SME
Mode selection at the end of Start back-tacking
Setting time interruption at each section end of
Back-Tacking.
HVP -20 Parameters List for DA-281 (MAC. 73)--version 1.0 N
ONON/OFFAutomatic sewing End back-tacking10 ACD
Parameters
Code
2 SLM Slow start operation mode
Start back-tacking stitches setting ,【014. SBT】= ON valid
ON
J/B J
AA/M/SU/SD
CON
T
ON/OFF
A
CON/STP/TRM
0 - F
0 - 15 stitches
A/SU/SD
End back-tacking stitches setting ,【021. EBT】 = ON valid
27
ON
0 - F
End back-tacking selection ON/OFF
0 - 15 stitches
800 - 990 msCT
21
T/A