Instruction manual

PAGE 11
software version : D2.8(FOR HVP70-4-ED only)
100 ohm 220 ohm 680 ohm 1000 ohm2200 ohm
DescriptionRangeParameters Function
Parameters
Code
Preset For
HVP-70 Sewing Machine Controller Parameters Setting List (for durkopp) E2
KEY
MAKE
R
208 VER
Software Version
- D2.8 D2.8 D2.8 D2.8 D2.8 software version display only
Define the source of Index point is from needle up si
g
nal or needle down si
g
nal.
UP： The reference index point is from the needle up si
g
nal .
DN： The reference index point is from the needle down si
g
nal.
210 FK1
Thread Clamp start an
g
le.
0 - 359 degrees 0 0 0 70 0
Thread Clamp output start an
g
le settin
g
.
211 FK2
Thread Clamp end an
g
le.
0 - 359 degrees 0 0 0 140 0
Thread Clamp output end an
g
le settin
g
.
212 THP
The timin
g
prior to HP speed
80 - 500 ms 100 100 100 100 100
Settin
g
the timin
g
prior to HP speed.
Settin
g
the number of stitches for HP function of walkin
g
foot .
0 : Function disable.
1 ~ 255 : Enable. Valid onl
y
when
[
062. HPM
]
=ALT.
Needle coolin
g
output mode selection.
0 : Normal needle coolin
g
function.
1 : Needle coolin
g
operates when sewin
g
speed excesses the settin
g
value of
[
216. NK
]
.
2 : Under ed
g
e trimmer.
215 DK
Settin
g
the needle coolin
g
dela
y
time
0 - 2550 ms 2500 2500 2500 2500 2500
Settin
g
the needle coolin
g
dela
y
time from motor stops
216 NK
Settin
g
the needle coolin
g
operatin
g
point
40 - 6000 spm 40 40 40 40 40
Needle cooling will operate when sewing speed excesses this setting value. Valid only when [214. FNK] =1.
Lift roller output mode selection.
0 : Roller works independentl
y
.
1 : Roller works with foot lifter and back tackin
g
.
2 : Roller works with foot lifter.
3 : Roller works with back tackin
g
.
Tension release output mode selection.
0 : Tension R. output depends on the timin
g
of
[
080. LLM
]
onl
y
.
1 : Tension R. operates with foot liftin
g
after motor stop.
2 : Tension R. operates with foot liftin
g
after trimmin
g
or power on.
3 : Operation and reduction of thread tension output on with foot lifting
durin
g
motor sto
p
or after thread trimmin
g
or
p
ower on.
Define the input function of IN5.
DB3 : Motor is runnin
g
b
y
[
191. B3
]
speed.
NOP : No function.
S5B : Motor is runnin
g
b
y
bar tackin
g
[
006. B
]
speed.
F : A switch input si
g
nal for knee switch.
Define the input function of INB.
NOP : No function.
PSD : Emer
g
enc
y
stop for down position.
SPB : Speed limited b
y
end back-tackin
g
[
005. V
]
speed.
Define the input function of INJ.
NOP : No function.
BTL : backtack suppression/recall switch for SBT/ EBT onl
y
.
HP : The switch for hi
g
h lift for walkin
g
foot.
U : Needle up switch.
(
b
y
[
125. USM
]
settin
g)
.
S1 : Motor is runnin
g
b
y
VC, if
[
143. AT
]
=ON; then runnin
g
b
y
[
009. A
]
speed.
Trimmer protection function selection when the machine pulle
y
was moved out of the ran
g
e of
[
224.
ON :
[
223. S2P
]
function valid.
OFF :
[
223. S2P
]
function invalid.
Operation mode selection. Valid onl
y
when
[
222. TOF
]
=ON.
NO : Operate foot liftin
g
onl
y
, without up needle and thread trimmin
g
.
PS : Operate foot liftin
g
and up needle onl
y
, without thread trimmin
g
224 TOA
Setting the range for thread trimmer
p
rotection when
[
222. TOF
]
= ON
5 - 40 degrees 10 10 10 10 10
Setting angle for thread trimming signal when shifting the needle stop position before the thread
trimmin
g
si
g
nal.
Corner Function selection.
ON：Enable. The related setting includes【144. IN1】【153. INK】【157. O1】【158. O3】【160. O5 】
【161. O6 】Related parameter :【037. SMP 】【062. HPM 】【097.TK3 】【232. CTW 】【238. KHP 】
【199. FHP 】【245. NFO 】【246. NFC 】
OFF : Disable.
NFD : The output
(
A/21
)
for sewin
g
foot pressure.
WL : The output
(
A/21
)
for wiper on/off LED.
Connected parameters :
[
247. SLE
]
=ON ,
[
144. IN1
]
=STK ,
[
157. O1
]
=OT1
ON : Normal stitch len
g
th.
OFF : Lon
g
stitch len
g
th.
0 : The selected stitch len
g
th remains on.
1 : Switch to lon
g
stitches after thread trimmin
g
.
2 : Switch to normal stitches after thread trimmin
g
.
ON
0
NO
Define the source of Index ( reference )
point
UP/DN UP DN
0213 CHP
Setting the number of stitches for HP
function by hp switch (A/7 or B/1)
0 - 255 stitches
Lift roller function 0/1/2/3
0
0
Functions of the output "needle cooling" 0,1,2
DB3
218 STR Tension release output function 0/1/2/3
Definition INB=NOP/PSD/SPB (C/7) NOP/PSD/SPB PSD PSD
BTL221 INJ Definition INJ=NOP/BTL/HP/U/S1 (A/14)
N
OP/BTL/HP/U/S1
OFF222 TOF Trimmer protection function ON / OFF ON/OFF
NO223 S2P
Selecting the trimmer protection mode
when [222. TOF] = ON
NO/PS
SO3 SO3=NFD/WL output switchover (A/21) NFD/WL
CER
ON
ON/OFF OFF
0
ON/OFF
OFF
NFD NFD NFD NFD
OFFOFFCorner Function switchover
227 SLU Stitch length for backtack
226
225
UPDN
0
UP
0
0
DB3 DB3 DB3 DB3
30
219 IN5 Definition IN5=DB3/NOP/S5B/F (A/10) DB3/NOP/S5B/F
0
220 INB
228 STN
Stitch length in the next seam
(after the thread trimming operation)
2000/1/2
P
O
W
E
R
..
ON
217 FLK
209 IDX
214 FNK
BTLBTLBTL
0
NO
OFF OFF
OFFOFF
0
PSD PSD
NO
OFFOFF
NO
BTL
0
0
0
0
0
0
PSD
OFF
NFD
OFF
0
0
0
0
0
0
＋