Instruction manual

PAGE 10
software version : D2.8(FOR HVP70-4-ED only)
100 ohm 220 ohm 680 ohm 1000 ohm2200 ohm
DescriptionRangeParameters Function
Parameters
Code
Preset For
HVP-70 Sewing Machine Controller Parameters Setting List (for durkopp) E2
KEY
MAKE
R
Define the input function of IN4.
DB2 : Motor is runnin
g
b
y
[
190. B2
]
speed.
SPV : Speed limited b
y
VHP input. Speed curve controlled b
y
[
186. MS
]
,
[
187. WS
]
,
[
188. MIN
]
,
[
189.
NOP : No function.
S5 : Motor is runnin
g
b
y
medium speed
[
059. M
]
.
WL : Wiper output cancel switch.
INA input lo
g
ic si
g
nal inver
t
ON : The input lo
g
ic of each Input si
g
nal PSU is reversed.
OFF : The input lo
g
ic of each Input si
g
nal PSU is normal.
INB input lo
g
ic si
g
nal invert
ON : The input lo
g
ic of each Input si
g
nal PSD is reversed.
OFF : The input lo
g
ic of each Input si
g
nal PSD is normal.
INC input lo
g
ic si
g
nal invert
ON : The input lo
g
ic of each Input INC si
g
nal is reversed.
OFF : The input lo
g
ic of each Input INC si
g
nal is normal.
BL controller interface control function selection.
ON : Enable for Pe
g
asus BL controller function . NOTE : Valid onl
y
when
[
156. OD
]
=KS4.
OFF : Disable.
For the hemmin
g
g
uide device of USA Bottoms Associates Inc
.
OFF : Normal sewin
g
mode.
1 : For manual mode hemmin
g
g
uide device.
2 : For auto mode hemmin
g
g
uide device.
FSR : Input (D/6) of switching 2nd tension release , can activate the LED(D/14) and output of solenoid
(
A/20
)
. Connected
p
arameters :
[
218. STR
]
,
[
230. KFH
]
.
PO1 : Needle down pulse width output .
(
position 1
)
NFD : Input (D/4) of switch for reduction of foot pressure, can activate the LED(D/12) and output of
solenoid
(
A/21
)
. Connected
p
arameter :
[
231. MFD
]
.
PO2 : Needle up pulse width output .
(
position 2
)
FSR
NFD NFDAO3 Definition AO3=PO2/NFD (A/21) PO2/NFD NFD
206 AO2 Definition AO2=PO1/FSR (A/20) PO1/FSR FSR FSR FSR
P
O
W
E
R
..
ON
DB2200 IN4 Definition IN4=DB2/SPV/NOP/S5/WL (A/9)
DB2/SPV/NOP/S
5/WL
OFF201 IAV INA = PSU logical signal invert (C/7) ON/OFF
OFF202 IBV INB = PSD logical signal invert (C/8) ON/OFF
OFF203 ICV INC logical signal invert (D/5) ON/OFF
Mode selection for hemming guide device
OFF204 BL BL CONTROLLER INTERFACE CONTROL ON/OFF
OFF,1,2 OFF
FSR
NFD NFD
OFFOFF
OFF
207
205 BAF
OFFOFF
OFF
OFF
OFF
OFFOFFOFF
OFFOFFOFF OFF
OFF
OFFOFFOFF
DB2DB2DB2 DB2
OFF
＋