Instruction manual

PAGE 6
software version : D2.8(FOR HVP70-4-ED only)
100 ohm 220 ohm 680 ohm 1000 ohm2200 ohm
DescriptionRangeParameters Function
Parameters
Code
Preset For
HVP-70 Sewing Machine Controller Parameters Setting List (for durkopp) E2
KEY
MAKE
R
Pro
g
ram mode selection.
NOP : No function
LOAD : Down load the pro
g
ram from C300 operation panel .
(
Valid onl
y
when
[
118. NOS
]
= OFF
)
SAVE : Save the pro
g
ram to C300 operation panel.
(
Valid onl
y
when
[
118. NOS
]
= OFF
)
Function for the needle up switch. (Connection : [145. IN2] =U or [221. INJ] =U or C300 operation panel
needle u
p
switch
)
A
: Stitch chan
g
eover + inchin
g
B : Stitch chan
g
eover onl
y
C : Up needle onl
y
.
D : Up needle and presser foot .
E : Inchin
g
one stitch onl
y
.
F : Inchin
g
one stitch backward onl
y
.
(
Note : Valid onl
y
when
[
010. ACD
]
= OFF,
[
011. RVM
]
= B
)
G : Backward runnin
g
for
[
133. CHS
]
settin
g
stitches.
ON : Alwa
y
s enable.
OFF : Enable onl
y
at intermediate stop .
127 MAV
Maximum volta
g
e hold
----- ----- ----- ----- ----- ----- Maximum voltage displa
y
128 MIV
Minimum volta
g
e hold
----- ----- ----- ----- ----- ----- Minimum voltage displa
y
129 PV
Current volta
g
e displa
y
----- ----- ----- ----- ----- ----- Power voltage display
130 OVD
Over volta
g
e settin
g
170V - 315V 305 305 305 305 305 Over voltage setting
131 LVD
Low volta
g
e settin
g
70V - 160V 100 100 100 100 100 Low voltage setting
Save the user's parameter setting into memory blocks for later use. Setting procedure:
1.Press [S] key + POWER ON LCD display [123. FA SET]
2.Press [P] key 9 times LCD display [132. UPG]
3.Press [S] key LCD display [UPG. 0]
4.Press [D] key to select a block number from [UPG. 0] ~ [UPG. 4].
5. Press [S] key to save the program.
Note : To recall the program, go to the memory block in [UPG. 0] ~ [UPG. 4] , use [C] key to call i
t
back and then
p
ress
[
S
]
ke
y
to confirm and save.
133 CHS
Function and stitches setting for Angle-
Stitch device ( Pegasus W582)
1 - 99 stitches 5 5 5 5 5
Valid only when [047. MAC] ＝『 10 』( For W582 angle stitch ) and [011. RVM] = 『 B 』.
When half heeling the pedal, the needle goes up , pressing down the pedal, this function works.
The『CHS』speed is set by [004. N] .
Full heeling back : Same as interlock stitch machine function output.
ON： The keys of A.B.C.D will be locked and defined to specific functions as follow :
[A] key : cancel presser foot after half heeling.
[B] key : cancel trimmer function at full heeling back.
[C] key : cancel wiper function at full heeling back.
[D] key : start constant stitch setting
OFF : Unlocked.
135 TOT
Auto-runnin
g
full time settin
g
1 - 168 Hrs 1 1 1 1 1
A
uto-running timer amount setting (when [138. UTD] = ON valid.)
136 TM1
Auto-runnin
g
on c
y
cle time settin
g
（1-250
)
x 0.1S
20 20 20 20 20
A
uto-running on timer setting
137 TM2
Auto-runnin
g
off c
y
cle time settin
g
（1-250
)
x 0.1S
20 20 20 20 20
A
uto-running off timer setting
ON : Running test function is enable
OFF : Running test function is non-enable
139 CK
Current sensor initial value
----- ----- ----- ----- ----- ----- Current sensor initial value display
Settin
g
the parameter
[
102. SE
]
from C-300 operation box .
ON : Enable.
OFF : Disable.
V
alid onl
y
when the double End Back-Tackin
g
is performed.
ON : Enable provided the parameter
[
030. BCC
]
= ON .
OFF : Disable.
See the connection dia
g
ram .
ON : Enable. S0,S1,S2,S3 as input of Actuator EB301/EB302 of EFKA.
OFF : Disable.
A
utomatic standin
g
operation can be done.
ON : Enable.
OFF : Disable.
123 FASET Factory default reset Factory setting reset
124 PG
Program down load from /save to operation
box (C300) / computer
NOP/LOAD/SAVE NOP NOP NOP NOPNOP
OFF
125 USM Function for the needle up switch
126 USA Mode selection for [125. USM] ON/OFF
A/B/C/D/E/F/G B
0132 UPG User program saving 0 - 4
OFF134 KLK SBT/EBT Key Lock selection ON/OFF
OFF138 UTD Auto-running test selection ON/OFF
OFF140 OSE Outside setting the [102. SE] parameter ON/OFF
OFF141 BC3
Added 1 stitch to the second C segment of
double End Back-Tacking
ON/OFF
OFF142 EFK EFKA pedal unit function ON/OFF
OFF143 AT
Automatic standing operation (S0/S1 low-
speed SW)
ON/OFF
P
O
W
E
R
..
ON
OFFOFFOFF OFF
OFFOFFOFF
OFFOFFOFF OFF
OFF
OFFOFFOFF
OFFOFFOFF OFF
OFF
OFFOFFOFF
0000
OFF
OFFOFFOFF
BBBB
OFF
＋