Instruction manual

PAGE 5
software version : D2.8(FOR HVP70-4-ED only)
100 ohm 220 ohm 680 ohm 1000 ohm2200 ohm
DescriptionRangeParameters Function
Parameters
Code
Preset For
HVP-70 Sewing Machine Controller Parameters Setting List (for durkopp) E2
KEY
TECH.
Mesh counter mode selection.
C : B
y
stitch counter,
T : B
y
timer.
Ed
g
e sensor function selection..
ON : Enable.
OFF : Disable.
100 SRS
Ed
g
e sensor si
g
nal check 1
0 - 99 stitches 1 1 1 1 1
Onl
y
valid when
[
099. SEN
]
set at ON. To avoid photo interference. Unit controlled b
y
[
098. MST
]
101 CMS
Ed
g
e sensor si
g
nal check 2
0 - 99 stitches 3 3 3 3 3
Onl
y
valid when
[
099. SEN
]
set at ON. To avoid photo interference. Unit controlled b
y
[
098. MST
]
102 SE
Settin
g
stitches from ed
g
e sensin
g
to stop
1 - 999 stitches 6 6 6 6 6
Settin
g
Stitches to stop., when ed
g
e si
g
nal detected. Onl
y
valid when
[
099. SEN
]
set at ON
When ed
g
e si
g
nal detected out. Motor will do the trimmin
g
c
y
cle automaticall
y
.
ON : After the stitches of
[
102. SE
]
finished, trimmin
g
works
.
OFF : After the stitches of
[
102. SE
]
finished, trimmin
g
doesn't work.
104 PSU Stitches for emergency up-stop 1 - 99 stitches 6 6 6 6 6
When [PSU] signal detected, running the stitches then stop at UP position.
The s
p
eed of settin
g
is set b
y
[
009. A
]
.
105 PSD Stitches for emergency down-stop 1 - 99 stitches 6 6 6 6 6
When [PSD] signal detected, running the stitches then stop at DOWN position.
The s
p
eed of settin
g
is set b
y
[
009. A
]
.
When the pedal on and the ed
g
e si
g
nal detected, the motor can start runnin
g
.
ON : Enable.
OFF : Disable.
When motor runnin
g
, manuall
y
push the Touch Back switch , reverse solenoid en
g
a
g
ed on at needle
ON : Valid.
OFF : Invalid.
When motor runnin
g
, manuall
y
push the Touch Back switch , reverse solenoid en
g
a
g
ed on at needle
ON : Valid.
OFF : Invalid.
Durin
g
sewin
g
, reverse output will be OFF at needle UP or DOWN position .
ON : A
t
『 needle UP 』position.
OFF : A
t
『 needle DOWN 』position.
The trimmin
g
and reverse solenoid activated on the same time.
ON : Valid.
OFF : Invalid.
Correction Mode of Touch-Back Switch mode selection. Note :
[
010. ACD
]
= OFF and
[
011. RVM
]
= B
1 : Doin
g
correction with one touch the Touch-Back switch .
2 : Doin
g
correction with double touch the Touch-Back switch.
W : Re
g
ular wi
p
er function
(
active 1 time when full heelin
g
back after sewin
g)
O : Wiper works at each full heelin
g
back
(
unlimited
)
A
: Wiper works onl
y
the pedal is kept full heelin
g
back . Wiper turn off when the pedal return to neutral.
Note : Wiper on time controlled b
y
the
[
093. W2
]
.
113 DEG
Needle DOWN position stop an
g
le
5 - 180 degrees 12 12 12 12 12
A
djust the needle down stop position.
114 UEG
Needle UP position stop an
g
le
5 - 180 degrees 12 12 12 12 12
A
djust the needle up stop position.
Power on displa
y
condition selection.
ON : When power switch turned on, the panel displa
y
s previous condition.
(
Keep previous condition
)
.
OFF : When power switch turned on, the panel displa
y
s normal mode.
116 DRU
Reverse angles through Needle down and
u
p
1 - 360 degrees 180 180 180 180 180
Valid only when [078. TRM] =『RK』mode
Motor reverses from needle down, and sto
p
s at the needle u
pp
er dead
p
oint.
117 ER
Error code displa
y
10 SET/FIFO
-----
Error code histor
y
displa
y
, total 10 events can be memorized.
ON : Without the s
y
nchronizer , motor is runnin
g
as a clutch motor and stops at random position.
OFF : With s
y
nchronizer .
ON : Direct drive.
OFF : Belt drive.
FU : Regular operation -- full heeling for trimming and foot lifting.
NU : Full heeling for up needle.
NO : No foot lifting function.
NUF : Full heeling for foot lifting and up needle.
EFF : Full heeling for foot lifting and running at low speed.
ON : Automatic needle UP at power on.
OFF : Function invalid.
P
O
W
E
R
..
ON
OFF115 PMD Power on display condition ON/OFF
C98 MST Mesh counter by timer or by stitch count C/T
OFF99 SEN Edge sensor function selection ON/OFF
ON/OFF OFF103 SET Trimming mode at sensory stop
ON ON ON ON106 PSN Re-start function at emergency stop ON/OFF
OFF107 S7U
Manual Back-Tacking engaged at needle-
up position
ON/OFF
ON108 S7D
Manual Back-Tacking engaged at needle-
down position
ON/OFF
OFF109 ROF Mode for de-engaging Back-Tacking ON/OFF
OFF110 TB Mode for Back-Tacking at trimming cycle ON/OFF
2111 COR Correction Mode of Touch-Back Switch 1/2
W112 WMD Wiper function related to full-heeling pedal W/O/A
OFF118 NOS Converting to a clutch motor selection ON/OFF
OFF119 DD Direct drive or belt drive ON/OFF
OFF
FU120 FHM
Mode selection for full-heeling after power
on or trimming
FU/NU/NO/NUF/
EFF
121 ANU Needle goes up as power turned ON ON/OFF
5000122 HL Upper limit of maximum speed 50 - 9999 spm The motor's maximum speed setting.700020001000 4000
OFFOFFOFF
FUFUFU FU
OFF
OFFOFFOFF
OFFOFFOFF OFF
OFF
OFFOFFOFF
WWWW
OFF
222
OFFOFFOFF OFF
2
OFFOFFOFF
ONONON ON
OFF
OFFOFFOFF
OFFOFF OFFOFF
ON
OFF
OFFOFFOFF
CCCC
OFF
＋