Instruction manual

PAGE 4
software version : D2.8(FOR HVP70-4-ED only)
100 ohm 220 ohm 680 ohm 1000 ohm2200 ohm
DescriptionRangeParameters Function
Parameters
Code
Preset For
HVP-70 Sewing Machine Controller Parameters Setting List (for durkopp) E2
KEY
TECH.
Foot Lifter output si
g
nal converted.
ON : The foot lifter
g
oes up durin
g
sewin
g
.
OFF : Function invalid.
Trimmin
g
device protection for cover stitch machine.
NC : Normal close. When si
g
nal at open , motor immediatel
y
stops and rotation s
y
mbol will stop.
NO : Normal open. When si
g
nal at close , motor immediatel
y
stops and rotation s
y
mbol will stop.
With TCL tri
gg
er si
g
nal input, the next trimmin
g
will be cancelled as full heelin
g
the pedal.
ON : Valid.
OFF : Invalid.
Cancelin
g
the interlock timer for quick restartin
g
. For machine without trimmer device onl
y
.
ON : Valid.
OFF : Invalid.
Motor runnin
g
mode at trimmin
g
sequence selection.
LK : For
g
eneral Lock-Stitch machines .Trimmin
g
from needle down to up.
RK : For Chain stitch machine eas
y
pull out c
y
cle. Needle stops with a reverse an
g
le set b
y
[
116. DRU
]
.
KA : For
g
eneral Cover stitch machines with under trimmer onl
y.
KB : For special Cover stitch machines with upper trimmer .
KC : Valid onl
y
when
[
079. LTM
]
=TK and
[
081. TS
]
＞0, otherwise function same as LK mode.
Reference the timin
g
chart of HVP-70.
T1 : At down position dela
y
ed
[
081. TS
]
an
g
les on, at up position dela
y
ed
[
083. T2
]
time off.
T2 : At down position dela
y
ed
[
081. TS
]
an
g
les on, extended
[
084. TE
]
an
g
les off.
T3 : At down position dela
y
ed
[
081. TS
]
an
g
les on, extended
[
083. T2
]
time off.
T4 : At down position dela
y
ed
[
082. T1
]
time on, extended
[
083. T2
]
time off.
TK : At up position dela
y
ed
[
082. T1
]
time on, extended
[
083. T2
]
time off.
TS : At down position alwa
y
s on, at up position dela
y
ed
[
082. T1
]
time on, extended
[
083. T2
]
time.
T7 : At down position dela
y
ed
[
081. TS
]
an
g
les on, at up position off, and dela
y
ed
[
082. T1
]
time on,
Reference the timin
g
chart of HVP-70.
L1 : At down position dela
y
ed
[
085. LS
]
an
g
les on, at up position dela
y
ed
[
087. L2
]
time off.
L2 : At down position dela
y
ed
[
085. LS
]
an
g
les on, extended
[
088. LE
]
an
g
les off.
L3 : At down position dela
y
ed
[
085. LS
]
an
g
les on, extended
[
087. L2
]
time off.
L4 : At down position dela
y
ed
[
086. L1
]
time on, extended
[
087. L2
]
time off.
LK : At up position dela
y
ed
[
086. L1
]
time on, extended
[
087. L2
]
time off.
LS : At down position alwa
y
s on, at up position dela
y
ed
[
086. L1
]
time on, extended
[
087. L2
]
time off.
L7 : At down position dela
y
ed
[
085. LS
]
an
g
les on, at up position off, and dela
y
ed
[
086. L1
]
time on,
81 TS
Dela
y
ed an
g
les prior to trimmer en
g
a
g
ed
0 - 360 degrees 0 0 0 105 0
V
alid for
[
079. LTM
]
= T1/T2/T3/T7 .
82 T1
Dela
y
ed timin
g
prior to trimmer en
g
a
g
ed
0 - 990 ms 0 0 0 0 0
V
alid for
[
079. LTM
]
= T4/TK/TS/T7.
83 T2
Trimmin
g
time
0 - 990 ms 0 0 0 0 0
V
alid for
[
079. LTM
]
= T1/T3/T4/TK/TS/T7.
84 TE
Settin
g
an
g
les of trimmin
g
0 - 360 degrees 0 0 0 161 0
V
alid for
[
079. LTM
]
= T2 .
85 LS
Dela
y
ed an
g
les prior to tension release
0 - 360 degrees 0 0 147 231 0
V
alid for
[
080. LLM
]
= L1/L2/L3/L7 .
86 L1
Dela
y
ed timin
g
prior to tension release
0 - 990 ms 0 0 0 0 0
V
alid for
[
080. LLM
]
= L4/LK/LS/L7.
87 L2
Extended timin
g
of tension release be
y
ond
0 - 1500 ms 50 50 50 50 50
V
alid for
[
080. LLM
]
= L1/L3/L4/LK/LS/L7.
88 LE
Settin
g
an
g
les of tension release
0 - 360 degrees 0 0 0 0 0
V
alid for
[
080. LLM
]
= L2 valid.
89 D1
Dela
y
ed timin
g
prior to trimmer en
g
a
g
ed a
t
0 - 990 ms 0 30 30 0 0
90 D2
Settin
g
timin
g
of trimmin
g
at down-stop
0 - 2500 ms 0 90 90 0 0
91 D3
Timin
g
recall of trimmin
g
at down-stop
0 - 990 ms 0 120 120 0 0
92 W1
Dela
y
ed timin
g
prior to wiper en
g
a
g
ed
0 - 980 ms 0 0 0 0 0 Time setting between needle up to wiper active.
93 W2
Settin
g
timin
g
of wipin
g
0 - 9990 ms 100 100 100 100 100 Wiper active timer setting.
94 WF
Dela
y
ed timin
g
prior to foot lifter en
g
a
g
ed
0 - 990 ms 50 50 30 30 50 Timer setting between wiper active to presses foot active.
Condense-Stitch function b
y
[
027. CT
]
timer for needle up & motor stop.
ON : Enable. Note : [021. EBT] =ON, [022. EBC] =8, [023. EBD] =3 and [024. EBN] =2 and [027. CT]
=100 must be ad
j
usted.
OFF : Disable.
96 RFC Backtacking output chopping duty-cycle 10 - 100 % 40 40 40 40 40
Only valid when [063. FTP] set at「M」mode. For solenoid's switching power adjustment.
Note : Wron
g
l
y
ad
j
ustment will cause the solenoid unable to lift or over-heatin
g
.
0 - 2500 ms Tape cutter on timer settin
g
x10 = 100 ms.
0 - 250 stitches
When 【042.CUD】= US,DS the value is bobbin counter alarm preaction value.
P
O
W
E
R
..
ON
ON/OFF74 FRV Converter for Foot Lifter signal output
78 TRM
NO
OFF OFF OFF OFFOFF
Thread trimmer cancel
75 SFM Safety switch protection mode NC/NO NO
76 TCL
Motor running mode at trimming sequence
77 ILC
Cancel of interlock timing after full heeling
pedal
KB
ON/OFF OFF OFF
ON/OFF
KB LK LKLK/RK/KA/KB/KC
OFF OFF OFF
OFF
LS
TS79 LTM
Mode selection for trimming sequence.
For TM output signal.
T1/T2/T3/T4/TK/
TS/T7
80 LLM
Mode selection for tension-release
sequence. For ML output signal
L1/L2/L3/L4/LK/
LS/L7
Only valid when [078. TRM] set at『 KB 』mode.
Signal output from the wiper MW.
See the KB timin
g
chart.
95 CSF Condense-Stitch function selection ON/OFF OFF OFF OFF OFF
LSL1LS
NONO
TS
OFF
TS TS
OFF
NO
OFF
OFF
KB
T2
L1
OFF
10 1097 TK3 Tape cutter on timer 10 10 10
＋