Instruction manual

PAGE 3
software version : D2.8(FOR HVP70-4-ED only)
100 ohm 220 ohm 680 ohm 1000 ohm2200 ohm
DescriptionRangeParameters Function
Parameters
Code
Preset For
HVP-70 Sewing Machine Controller Parameters Setting List (for durkopp) E2
KEY
TECH.
47 MAC
Machine Code
0~92 73 85 86 83 92
Machine code switchover
Positionin
g
Mode selection.
ON : One position UP onl
y
.
OFF : Two positions Up / DOWN.
49 SPD
Machine's pulle
y
dimension.
1 - 250 mm 75 75 75 75 75 Setting machine pulley size when [051. PL] = ON valid
50 MPD
Motor's pulle
y
dimension.
1 - 250 mm 75 75 75 75 75 Setting motor pulley size when [051. PL] = ON valid
Selectin
g
the mode of settin
g
pulle
y
ratio.
ON : Manuall
y
settin
g
the pulle
y
sizes b
y
[
049. SPD
]
,
[
050. MPD
]
.
OFF : Automaticall
y
settin
g
the pulle
y
sizes b
y
the CPU.
52 BT Braking time of motor 150 - 500 ms 200 200 200 200 200
Braking time of motor
Note : Onl
y
valid when
[
054. BK
]
set at ON.
Soft start at the first c
y
cle of power ON function selection.
ON : Enable and speed is set b
y
[
007. S
]
.
OFF : Disable.
Motor stops with brake function.
ON : Enable.
OFF : Disable.
V
alid onl
y
when needle stops at up position.
ON : Enable. When the needle stops at up position, the first stitching will be done with a reverse angle
which is set b
y
the
[
056.SRA
]
.
OFF : Disable.
Exce
p
tion : If
[
147. INA
]
= BCR, an external switch ma
y
be used as a selection of ON / OFF to this
56 SRA
Settin
g
the an
g
les of
[
055. SRM
]
1 - 360 degrees 60 60 60 60 60
V
alid onl
y
when
[
055. SRM
]
= ON.
ON : Enable.
OFF : Disable.
58 TR8
Settin
g
the an
g
les of
[
057. TRU
]
1 - 360 degrees 14 28 20 63 14
V
alid only [057. TRU] = ON
59 M
Medium speed
low - 8000 spm 800 800 800 800 800 Medium speed adjustment
60 L
Low speed
50 - 500 spm 180 100 150 150 180 Low speed adjustments
61 T
Thread trimmin
g
speed
50 - 500 spm 180 100 150 150 180 Thread trimming speed adjustments
For machines have HP function onl
y
.
[
ALT
]
mode : Presser for liftin
g
stroke chan
g
ed b
y
each time of the HP switch pushed on.
[
MON
]
mode : Presser foot liftin
g
stroke must be remained b
y
the HP switch kept on.
M : Ma
g
netic t
y
pe.
A
: Air t
y
pe
.
Note : When set at A t
y
pe,
[
064. FO
]
and
[
065. FC
]
settin
g
will be invalid. It will be full on
.
64 FO
Full-On time settin
g
for foot liftin
g
solenoid
0 - 990 ms 180 350 350 350 180
Onl
y
valid when
[
063. FTP
]
set at『 M 』mode. For solenoid pullin
g
torque ad
j
ustment.
65 FC
Presser foot lifting output chopping duty-
c
y
cle
10 - 90 % 40 40 40 40 40
Only valid when [063. FTP] set at「M」mode. For solenoid's switching power adjustment.
Note : Wron
g
l
y
ad
j
ustment will cause the solenoid unable to lift or over-heatin
g
.
66 FD
Runnin
g
-Dela
y
time settin
g
after foot lift
0 - 990 ms 80 80 120 80 80
If Foot Lifter is installed, set 100 ms min. to ensure the presser foot come down first.
Selection of solenoid protection.
ON : The foot liftin
g
solenoid activated time will be controlled b
y
[
068. FP
]
.
OFF : The foot liftin
g
solenoid will be alwa
y
s active unless heelin
g
back the pedal.
68 FP
Workin
g
time limit settin
g
for Foot Lifte
r
(0-9990) x 0.01s 3000 3000 3000 3000 3000 Setting the lifting solenoid activated time. Valid only when the [067. FPM] = ON.
69 HD
Sensitivity adjustment for half-heeling
pedal
0 - 990 100 100 100 100 100
Use this setting as PF delay time at half heeling the pedal. If Foot Lifter is installed, set 100 ms min.
1.If timing set to short, it will cause PF started once before trimming at full heeling the pedal.
2.If timin
g
set to lon
g
, it will cause PF started too slow or la
gg
ard at half heelin
g
the
p
edal.
ON : No foot liftin
g
at half-heelin
g
.
(
but full-heelin
g
can operate foot lifter
)
OFF : Operate foot liftin
g
at half-heelin
g
.
Note : When
[
134. KLK
]
= ON for interlock-stitch machine, this function can be controlled b
y
A ke
y
on
ON : No foot liftin
g
at heelin
g
pedal.
OFF : Has foot liftin
g
at heelin
g
pedal.
ON : No function at heelin
g
pedal.
(
foot lifter and need up function are also invalid
)
OFF : Trimmer is functioned at heelin
g
pedal.
When the pedal is returned to neutral position, trimmin
g
works automaticall
y
.
ON : Enable. Onl
y
valid when
[
072. FHC
]
= OFF
OFF : Disable.
NTC Thread trimming activate at neutral pedal73
67 FPM Protection for foot lifter solenoid.
71 FL
57
55
54
48
53
N12
Positioning Mode selection.
（ON=UP ONLY, OFF=UP/DOWN）
ON/OFF OFF OFF OFF
BK Motor brake at normal stop
POL Soft start at the first cycle of power ON ON/OFF ON
OFF OFFON/OFF OFF
OFF
51 PL Motor pulley ratio mode adjustment ON/OFF OFF OFF
OFF
SRM Motor returned at start running selection ON/OFF OFF
OFFOFF
OFF
MON MON ALT
OFF OFF OFF
TRU
Motor stops with a reverse angle after
trimming
ON/OFF OFF
62 HPM
Mode for foot lifting stroke change at
special compound feed machine.
ALT/MON
M
OFF OFF OFFON
ALT
M
ON/OFF ON
MON
63 FTP Type selection for foot lifting solenoid M/A M M M
OFF
OFF70 HHC
Cancel presser foot lifting with half-
heeling pedal
ON/OFF
ON/OFFCancel foot lifting at full- heeling pedal
OFF72 FHC Cancel trimming at Full-Heeling pedal ON/OFF
OFFOFFOFFOFF OFFON/OFF
P
O
W
E
R
..
ON
OFFOFFOFF
OFFOFFOFF OFF
OFF
OFFOFFOFF
ONONON ON
OFF
ONON
OFFOFF OFF
ON ON
＋