Instruction manual

PAGE 2
software version : D2.8(FOR HVP70-4-ED only)
100 ohm 220 ohm 680 ohm 1000 ohm2200 ohm
DescriptionRangeParameters Function
Parameters
Code
Preset For
HVP-70 Sewing Machine Controller Parameters Setting List (for durkopp) E2
KEY
USER
A
dded 1 stitch to the C se
g
ment of End back-tackin
g
function selection.
ON : valid
OFF : Invalid
Bar-tackin
g
mode selection.
A
: One shot sewin
g
.
M : Pedal control and motor can stop at middle wa
y
.
SU : One shot sewin
g
but motor stops at needle up b
y
[
027. CT
]
timer at end of each seam.
SD : One shot sewin
g
but motor stops at needle down b
y
[
027. CT
]
timer at end of each seam.
V
alid onl
y
when the operation panel disconnected.
ON : Perform
OFF : Not perform.
33 BRC
Settin
g
stitches of Bar-tackin
g
0 - 99 stitches 4 4 4 4 4
One settin
g
for all seams ,
[
032. BAR
]
= ON valid
.
34 BRN
Settin
g
turns of Bar-tackin
g
0 - 15 times 4 4 4 4 4
Settin
g
the seam times of Bar-tackin
g
,
[
032. BAR
]
= ON valid
.
35 BT5
Stitch balance for Bar-tackin
g
5
3 4 4 4 3 BT5=0 : Invalid, 1-8 : Increase stitches of reverse seam; 9-F : Increase stitches of forward seam
36 BT6
Stitch balance for Bar-tackin
g
6
7 3 3 3 7 BT6=0 : Invalid, 1-8 : Increase stitches of forward seam; 9-F : Increase stitches of reverse seam
Constant-stitch sewin
g
mode selection.
A
: One shot sewin
g
.
M : Pedal control and motor can stop at middle wa
y
.
V
alid onl
y
when the operation panel disconnected.
ON : Perform.
OFF : Not perform.
Settin
g
stitches for section 1～4 of
15 15 15 15 15 Stitches setting of seam P1-P4. [038. PM] = ON valid.
Settin
g
stitches for section 5～F of
0 0 0 0 0 Stitches setting of seam P5-PF. [038. PM] = ON valid.
Wiper / thread clamp function selection.
ON : Enable.
OFF : Disable.
Trimmer function selection.
ON : Enable.
OFF : Disable.
Counter function mode selection.
NOP : The counter is invalid.
U : Count up b
y
stitches. When count over , counter will be auto- reset.
D : Count down b
y
stitches. When count over , counter will be auto- reset.
US : Count up by stitches. When count over, motor stops and the counter must be reset by the external
switch S4
[
152.INI
]
=CRS or the A ke
y
on the front
p
anel..
DS : Count down by stitches. When count over, motor stops and the counter must be reset by the
external switch S4
[
152.INI
]
=CRS or the A ke
y
on the front
p
anel..
UT : Count up b
y
trimmin
g
. When count over , counter will be auto- reset.
DT : Count down b
y
trimmin
g
. When count over , counter will be auto- reset.
UTS : Count up by trimming. When count over, motor stops and the counter must be reset by the
external switch S4
[
152. INI
]
=CRS or the A ke
y
on the front
p
anel..
DTS : Count down by trimming. When count over, motor stops and the counter must be reset by the
external switch S4
[
152. INI
]
=CRS or the A ke
y
on the front
p
anel..
43 UD Setting Count amount 1 - 9999 99 99 99 99 99
Count setting . (Note : The real number = the value of [003. CNR] X [043. UD] , when [042. CUD]
=U,D,US,UD valid onl
y
.
)
44 PN
Displa
y
counter
0-9999 0 0 0 0 0
Displa
y
the current count of
[
043. UD
]
45 SP
Sewin
g
speed displa
y
0 - 8000 spm 0 0 0 0 0
Showin
g
the current sewin
g
speed.
Motor rotation direction adjustments. ( Viewed from the motor shaft side )
Connection :
[
119. DD
]
CCW : counterclockwise.
CW : clockwise.
WON Wiper / thread clamp function selection ON40
46
42
ON30 BCC
Added 1 stitch to the C segment of End
back-tacking
ON/OFF
A/M/SU/SD A31 SMB Mode selection for Bar-tacking
OFF OFF OFF OFF32 BAR Bar-tacking selection ON/OFF
M
0 - F
37 SMP Mode selection for Constant-stitch sewing A/M
OFF
39 PS 0 - 250 stitches
PM Constant-stitch sewing selection ON/OFF OFF38 OFF
ON ON
OFF OFF
ON
41 TM Trimmer function selection ON/OFF ON ON ON ON
ON/OFF
CUD
Count mode selection (For Bobbin Thread
or Sewing Piece)
NOP/U/D/US/DS/
UT/DT/UTS/DTS
NOP NOP NOP NOP
DIR Direction of motor rotation CW/CCW CW CW CW CW
P
O
W
E
R
..
ON
MMM
AAA
OFF
M
ONOFFOFF OFF
A
ON
ON
NOP
CW