Instruction manual

- 32 -
11. Example of setting counter function (Refer to the Technical Documents for details on setting the up counter.)
* When using down counter as a bobbin thread level counter (Ending count after 10,000 stitches)
(1) The current down counter value [D] is decremented by one each time ten stitches are stitched.
(2) When the remaining down counter [D] reaches 0, stitching is prohibited after trimming
(Stitching is possible until the thread is trimmed.)
(3) When the external switch I1, set with the [C] mode function selection, turns ON, the current down
counter value [D] value is set to the down counter value [N], and the next stitching is enabled.
(1)
Call out the program mode [C] function [I1].
(This can be called with mode call or direct number call. Refer to
pages 14 to 16.
(Direct call number = "0357"))
(2)
* Press the [D] key and set the value to "CCD".
(3)
Set the function [I1].
For mode call: [p] + [n]
For direct number call: Set with
.
(4)
Call out the program mode [B] function [N].
(This can be called with mode call or direct number call. Refer to
pages 14 to 16.
(Direct call number = "0201"))
(5)
* Press the [A] to [D] keys and set the value to "1000".
(6)
Call out the program mode [B] function [D].
For mode call: [p]
For direct number call: Set with
, select number [202], and
then press
.
(7)
* Press the [A] to [D] keys and set the value to "1000".
(8)
Call out the program mode [B] function [CDN].
For mode call: [p]
For direct number call: Set with
, select number [210], and
then press
.
(9)
* Press the [D] key and set the value to "ST".
(10)
Call out the program mode [B] function [DNC].
For mode call: [p]
For direct number call: Set with
, select number [213], and
then press
.
(11)
* Press the [D] key and set the value to "ON".
(12)
Call out the program mode [B] function [CNU].
For mode call: [p]
For direct number call: Set with
, select number [217], and
then press
.
(13)
* Press the [C] and [D] keys and set the value to "10".
(14)
Entering the normal mode
For mode call: [Ļ] + [Ĺ]
For direct number call: Set with and then press .
Description
[C] mode function selection
[I1.CCD]: Sets the external input I1 to the counter clear signal [CCD].
[B] mode function selection
[N.1000]: Sets the down counter value. The down counter counts (subtracts) from the value set here.
[D.1000]: Current down counter value.
[CDN.ST]: The down counter is decremented by one each time the number of stitches set in [CNU] is stitched. (In this example, [CNU] is set to
10, so the down counter is decremented by one each time 10 stitches are stitched.)
* [DSC.ST]: When the current down counter [D] reaches 0, the next stitching is prohibited after trimming. The next stitching is enabled when the
external input I1, set with [C] mode function selection, turns ON.
[DNC. ON]: Down counter is validated. Set this to ON to use the down counter.
[CNU.10]: Set this to count every 10 stitches.
Items marked with an asterisk * are the factory settings.
Note) To clear the down counter with the P key on the
control switch panel set the following.
[C] mode function selection
[IP.CCD]: Sets the P key on the control switch panel to
the counter clear signal [CCD].