Instruction manual

- 20 -
Simple setting table for Mitsubishi thread trimming sewing machine and motor pulley outside diameter.
Speed setting Function setting
Function name Digital display Sewing machine type
High
speed
(H)
Low speed
(L)
Thread
trimming
speed
(T)
Start
tacking
speed
(N)
End
tacking
speed
(V)
D mode
tack
alignment
(BM)
A mode
weak
brake
(BK)
A mode
gain
selection
(GA)
Motor
pulley
outside
diameter
(mm)
*3
280M
LS2-1280-M1T (W) 4000 250 200 1700 1700 OFF OFF L
*1
280H
LS2-1280-H1T(W)
3000 250 200 1200 1200 OFF OFF L
280B
LS2-1280-B1T
3000 250 200 1200 1200 OFF OFF L
380M
LS2-1380-M1T(W) 4000 250 200 1700 1700 OFF OFF L
380H
LS2-1380-H1T(W)
3000 250 200 1200 1200 OFF OFF L
380B
LS2-1380-B1T
3000 250 200 1200 1200 OFF OFF L
85
210M LS2-2210-M1T(W) 4000 250 200 1700 1700 OFF OFF L
230M LT2-2230-M1TW 3700 250 175 1200 1200 OFF OFF H
230B LT2-2230-B1T 3000 250 175 1200 1200 OFF OFF H
250M LT2-2250-M1TW 3000 250 175 1200 1200 OFF OFF H
250B LT2-2250-B1T 3000 250 175 1200 1200 OFF OFF H
3310 LY2-3310-B1T 2000 250 225 700 700 ON OFF H
3319 LY2-3319-B1T 2000 250 225 700 700 ON OFF H
*2
3750 LY2-3750-B1T 2000 250 200 700 700 ON OFF L
6840 LY3-6840-B0T 2000 250 150 700 700 ON OFF H
65
6850 LY3-6850-B1T 2000 250 150 700 700 ON OFF L
410B LU2-4410-B1T 2000 250 175 700 700 ON OFF L
*8
412B LU2-4412-B1T 2000 250 175 700 700 ON OFF L
430B LU2-4430-B1T 2000 250 175 700 700 ON OFF L
4650 LU2-4650-B1T 3000 250 175 700 700 ON OFF L
*8
4652 LU2-4652-B1T 3000 250 175 700 700 ON OFF L
4710 LU2-4710-B1T 3000 250 175 700 700 ON OFF L
85
4730 LU2-4730-B1T 2500 250 175 700 700 ON OFF L
630 LX2-630-M1 800 280 160 500 500 ON ON L
65
280E LS2-1280-M1T(W) 5000 250 200 1700 1700 OFF OFF H
110
FL *5 5000 250 200 1700 1700 OFF OFF L
N *6 5000 250 200 1700 1700 OFF OFF L
LOAD2
*7
*4
LOAD1
*7
*1 Factory setting is [280M].
*2 The effective diameter of the sewing machine pulley is 70 mm.
(Note : In case of LY2-3310/3319/3750 is 80 mm, LU2-4410/4412/4430/4650/4652/4710/4730 is 85 mm.)
*3 A function name is displayed in order to the direction of ↓ every time it presses a [↓] key.
*4 A function name is displayed in order to the direction of ↑ every time it presses a [↑] key.
*5 For sewing machine with foot lifter, without thread trimmer.
*6 For needle positioner.
*7 It is possible to load the saved setting data by the function of [SAVE*] in the program mode [ I ].
( Program mode [ I ] : [↓]＋[↑]＋[B]＋[C] key )
( The factory setting of [LOAD1] is the setting data of [412B] and the factory setting of [LOAD2] is the setting data of [280M]. )
*8 The short remaining thread trimming function is set.