Technical Specifications

Duck Patch Liquid Rubber Wall Patch
A high performance, professional grade repair product
Revised: 08/08
Manufacturer:
ThorWorks Industries, Inc.
2520 S. Campbell St.
Sandusky, OH 44870
Phone: [phone]
Fax: [phone]
Description
DUCK PATCH LIQUID RUBBER WALL PATCH is a
highly elastomeric heavy-bodied polymer emulsion
patch material featuring advanced rubber technology.
It is ideal for filling holes and cracks in concrete
basement walls as well as sealing corner wall joints
and wall/floor joints.
USES
Exterior and interior concrete basement walls, above
or below grade. Concrete foundations, masonry and
retaining walls, poured concrete walls, cinder blocks,
Styrofoam foam boards, wood and metal.
SURFACE PREPARATION
Remove all dirt, dust, oil, form release compound
or loose paint. Remove any white powdery residue
(efflorescence) with stiff wire brush prior to applying
DUCK PATCH. WARNING: Old, existing paint on walls
may contain lead. Scraping and sanding old paint
may release lead dust which is toxic. EXPOSURE
TO LEAD DUST MAY CAUSE SERIOUS ILLNESS OR
BRAIN DAMAGE. Be sure to wear NIOSH approved
respirator to avoid breathing dust. You can log onto
www.epa.gov/lead/ for additional information.
APPLICATION
Apply DUCK PATCH with trowel or putty Knife. Fill
holes and cracks and allow material to overlap onto
sound surface beyond hole or crack. Level smooth
with trowel or putty knife. Allow patch material to dry
for 24 hours prior to coating with DUCK COAT LIQUID
RUBBER BASEMENT SEALER or other suitable paint
or coating. If needed, a second application of DUCK
PATCH may be added for additional filling purposes.
When sealing wall joints, DUCK PATCH should be
applied at a minimum of ¼” thick with material
extending at least ½” onto surface on each side of
joint for adequate long-term adhesion.
CLEAN UP
Wash tools with water before material dries.
WEATHER CONDITIONS
Indoor temperature should be 65º-70ºF during
application of DUCK PATCH. When applying DUCK
PATCH to exterior (outdoor) surfaces, temperature
should be a minimum of 60°F and rising during
application. Temperature shall not drop below 60°F
within 24 hours after application. In areas where dew
or fog accumulates in the early evening, it is best to
apply sealer in the morning. Stop coating by early
afternoon (3:00 pm) to avoid wash off, which will
occur if dew, fog, or rain arrives before coating dries.
Do not apply to outdoor surfaces if rain is imminent
or forecast within 24 hours after application.
COVERAGE
Ultimate coverage will depend upon thickness and
width of application.
PRECAUTIONS
Do not dilute. Do not allow contents in pail to freeze.
Use with adequate ventilation. KEEP OUT OF REACH
OF CHILDREN
FIRST AID
EYES: Flush immediately with large amounts of water
for at least 15 minutes.
Consult a physician if irritation persists.
INGESTION: Do not induce vomiting. Consult a
physician or medical facility immediately.
INHALATION: Remove to fresh air.
Contains less than 50 g/l VOC.
LIMITED WARRANTY
The statements made on this container are believed
to be true and accurate and are intended to provide
a guide for approved application practices. As
workmanship, weather, construction, condition of
surface, tools utilized, and other variables affecting
results are all beyond our control, the manufacturer
warrants only that the material is free from defects
and any liability to the buyer or user of this product
is limited to the replacement value of the product
only. The manufacturer expressly disclaims any
implied warranties of merchantability or fitness for a
particular purpose. In no event shall manufacturer be
liable for any injury, loss or damage, either direct or
incidental in connection with use of this material.
INGREDIENTS CAS No.
Water
Polymer
Titanium Dioxide
Ethylene Glycol
Calcium Carbonate
7732-18-5
Proprietary
13463-67-7
107-21-1
471-34-1
www.duckcoat.com
LIQUID RUBBER WALL PATCHLIQUID RUBBER WALL PATCH
FOR BASEMENT WALLS