Owner’s manual E DUCATI998Matrix 1
E 2
Hearty welcome among Ducati fans! Please accept our best compliments for choosing a Ducati motorcycle. We think you will ride your Ducati motorcycle for long journeys as well as short daily trips. Ducati Motor Holding s.p.a wishes you smooth and enjoyable riding. We are steadily doing our best to improve our “Technical Assistance” service. For this reason, we recommend you to strictly follow the indications given in this manual, especially for motorcycle running-in.
TABLE OF CONTENTS E General 6 Warranty 6 Symbols 6 Useful information for safe riding 7 Carrying the max load allowed 8 Identification data 9 Controls 10 Position of motorcycle controls 10 Instrument panel 11 Keys 12 Ignition switch and steering lock 13 Left switch 14 Clutch lever 15 Fast idle lever 16 Right switch 17 Throttle twistgrip 17 Front brake lever 17 Rear brake pedal 18 Gear change pedal 18 Setting the gear change and rear brake pedals 19 4 Main components and devices 21 Location 21 Tank fille
Chain tension inspection 50 Chain lubrication 50 Replacing bulbs 51 Beam setting 54 Rear view mirror adjustment 55 Tubeless tyres 55 Checking engine oil level 57 Cleaning and replacing the spark plugs 58 Cleaning the motorcycle 59 Storing the bike away 60 Important notes 60 For United States of America version only 72 Routine maintenance record 81 E Technical data 61 Overall dimensions 61 Weights 61 Top-ups 62 Engine 63 Timing system 63 Performance data 64 Spark plugs 64 Brakes 64 Transmission 65 Frame
GENERAL E Warranty In your own interest, and in order to guarantee product reliability, you are strongly advised to refer to a Ducati Dealer or Authorized Workshop for any servicing requiring particular technical expertise. Our highly skilled staff have access to the implements required to perform any servicing job at best, using Ducati original spare parts only as the best guarantee for full interchangeability, smooth running and long life. All Ducati motorcycles come with a “Warranty Card”.
Useful information for safe riding Warning Read this section before riding your motorcycle. Accidents are frequently due to inexperience. Always make sure you have your licence with you when riding; you need a valid licence to be entitled to ride your motorcycle. Do not lend your motorcycle to inexperienced riders or who do not hold a valid licence. Both rider and pillion passenger must always wear a safety helmet.
Carrying the maximum load allowed Your motorcycle is designed for long-distance riding, carrying the maximum load allowed in full safety. Even weight distribution is critical to preserving safety features and avoiding trouble when performing sudden manoeuvres or riding on bumpy roads. E Information about carrying capacity The total weight of the motorcycle in running order including rider, pillion passenger, luggage and additional accessories should not exceed 375 Kg.
Identification data All Ducati motorcycles have two identification numbers, for frame (fig. 1) and engine (fig. 2). Frame number Engine number E Note These numbers identify the motorcycle model and are required when ordering spare parts. fig. 1 fig.
CONTROLS 1 E Warning This section details the position and function of all the controls you need to drive your motorcycle. Be sure to read this information carefully before you use the controls. 8 4 5 3 6 7 2 Position of motorcycle controls (fig. 3) 1) Instrument panel. 2) Key-operated ignition switch and steering lock. 3) Left switch. 4) Clutch lever. 5) Cold start button. 6) Right switch. 7) Throttle twistgrip. 8) Front brake lever. 9) Gear change pedal. 10) Rear brake pedal. 9 10 fig.
7) High beam light (blue). Comes on when right high beam is on. 8) Water temperature indicator . Indicates engine coolant temperature. Important Stop riding if the temperature reaches the max. value, otherwise the engine might damage. When parking light is on, the instrument panel is lighted. 1 a 5 3 7 4 2 6 c ATICORS UC D E Instrument panel (fig. 4) 1) Speedometer (km/h or mph). Gives road speed. a) Odometer (km or miles). Gives total distance covered. b) Trip meter (km or miles).
Note Separate the two keys and keep the identification plate (1) in a safe place. DUCATI E 1 A C U D Note The keys have a small plate (1) attached that reports their identification number. TI Keys (fig. 5) Your Ducati was delivered with two universal keys for ignition, steering lock, seat catch and fuel filler plug. fig.
Ignition switch and steering lock (fig. 6) It is located in front of the fuel tank and has four positions: A) ON: lights and engine enabled; B) OFF: lights and engine disabled; C) LOCK: steering locked; D) P: parking light and steering lock. B A C D Note To move the key to the last two positions, press it down before turning it. Switching to (B), (C) and (D), you will be able to take the key out. Warning This model is equipped with an energy-saving CPU.
Left switch 1) Dip switch, light dip switch, two positions: position = low beam on; position = high beam on. E 4 2) Switch = 3-position turn indicator: centre position = off; position = left turn; position = right turn. To disable turn indicators, return switch to central position and push in. 3) Button = warning horn. 4) Button = passing. 14 1 3 2 fig.
Clutch lever (fig. 8) Lever (1) disengages the clutch. It features a dial adjuster (2) for lever distance from the twistgrip on handlebar. To set lever distance from twistgrip, push lever (1) fully forward and turn the dial adjuster (2) to one of its four positions. Remember that position no. 1 gives maximum distance between lever and twistgrip, whereas lever and twistgrip are closest when adjuster is set to position no. 4.
Fast idle lever (fig. 9) The fast idle lever (3) is used to start the engine from cold and to increase the engine idle rotation speed after starting. Control positions: A - (vertical) Control not activated B - Control fully activated The lever may also be placed on intermediate positions to match the progressive engine warming up (see page 34). E A B Important Never use this device when the engine is warm. Do not run with the fast idle control on. 1 16 fig.
Right switch (fig. 10) 1) Switch for ENGINE STOP, two positions: position (RUN) = run. position (OFF) = stop. Warning This switch is mainly intended for use in emergency cases when you need to stop the engine quickly. After stopping the engine, return the switch to the position to enable starting. Front brake lever (fig. 10) Pull in the lever (4) towards the twistgrip to operate the front brake. The system is hydraulically operated and you just need to pull the lever gently.
Rear brake pedal (fig. 11) Push down on the pedal (1) with your foot to operate the rear brake. The system is hydraulically operated. E 1 fig. 11 Gear change pedal (fig. 12) The gear change pedal is at rest when in the central position N, is moved up and down to change gears and then returns to the central position. down = push down on the pedal to engage 1st gear and to shift down. The N light will go out. up = lift the pedal to engage the 2nd gear and then the 3rd, 4th, 5th and 6th gear.
Setting the gear change and rear brake pedals (fig. 13 and 14) The gear change and rear brake pedals can be adjusted to suit the preferred riding position of each rider. To set the gear change pedal, lock linkage (1) and loosen the check nuts (2) and (3). Note Nut (2) has a left-hand thread. Fit an open-end wrench to the hexagon portion of linkage (1). Rotate linkage until setting pedal in the desired position. Tighten both check nuts onto linkage. E fig.
E To set the rear brake pedal, loosen check nut (4). Turn pedal travel adjusting screw (5) until pedal is in the desired position. Tighten check nut (4). Work pedal by hand to make sure it has 1.5 - 2 mm free play before brake begins to bite. If not so, set the length of cylinder linkage as follows. Loosen the check nut (6) on cylinder linkage. Tighten linkage into fork (7) to increase play, or unscrew linkage to reduce it. Tighten check nut (6) and check pedal free play again. fig.
MAIN COMPONENTS AND DEVICES 2 Location (fig. 15) 1) Tank filler plug. 2) Seat catch. 3) Side stand. 4) Hook for helmet fastening cable. 5) Steering damper. 6) Rear view mirrors. 7) Front fork adjusters. 8) Rear shock absorber adjusters. 9) Motorcycle track alignment linkage. 4 8 E 7 6 9 8 3 1 5 6 7 4 fig.
Tank filler plug (fig. 16) Opening Lift the protection lid (1) and fit the ignition key into the lock. Turn the key clockwise 1/4 turn to unlock. Lift the plug. E Closing Refit the plug with the key in it and push it down into its seat. Turn the key anticlockwise to its initial position and take it out. Close the lock protection lid (1). 1/4 OPEN DUCATI 0 1 Note The plug can only be closed with the key in. fig.
Seat catch and helmet hook Opening (fig. 17 and fig. 18) Fit the ignition key into the lock (1) and turn the key clockwise. Pull gently the tail guard (2) outwards and lift it until it rests onto the fuel tank. On the rear end of the compartment underneath the seat, there is the helmet fastening cable. Insert the cable (A) into the helmet and insert the ends of the cable into the hook. Leave the helmet hanging outside (fig. 18) and refit the seat.
Closing (fig. 19) Pull gently the tail guard outwards and lower it to its horizontal position. Press on the passenger pillion to allow the clips (3) – integral with the fairing - to catch the pins (4) – integral with the frame, until you hear the catch click. Pull the tail guard gently up to make sure it is firmly secured to the frame. 3 4 E fig.
Side stand (fig. 20) Important Before lowering the side stand, make sure that the bearing surface is hard and flat. Do not park on soft or pebbled ground or on asphalt melt by the sun heat and similar or the motorcycle may fall over. When parking in downhill road tracts, always park the motorcycle with its rear wheel facing downhill. To pull down the side stand, hold the motorcycle handlebars with both hands and push down on the thrust arm (1) with your foot until it is fully extended.
Steering damper (fig. 21) The steering damper is before the tank and is secured to the frame and the steering head. It gives improved steering accuracy and stability, thus also improving motorcycle road behavior under any riding conditions. E Important In case the headstock angle is changed, the steering damper must be repositioned (see page 49). fig. 21 26 Front fork adjusters The front fork has rebound and compression damping adjusters. This adjustment is done using the outer adjusters: 1) (fig.
STANDARD factory setting is as follows: compression: 12 clicks; rebound: 11 clicks. Max. setting range for softest damping adjustment is 14 clicks (both for rebound and compression). To change the preload of the spring inside each fork leg, turn the hex. adjusting nut (2) with a 22-mm hexagon wrench. Preload setting range (A, fig. 22) is from 25 to 10 mm. Factory setting is 20 mm. 1 A E Important Adjust both fork legs to same settings. 2 fig. 22 3 fig.
E Shock absorber adjusters (fig. 24) The shock absorber has outer adjusters that enable you to adjust your motorcycle to the load. The adjuster (1) located on the left side, on the connection holding the shock absorber to the swingarm, controls rebound damping. The adjuster (2) on the shock absorber expansion reservoir controls compression damping. Turn the adjusters (1 and 2) clockwise to increase damping, anticlockwise to reduce it.
Changing motorcycle track alignment (fig. 26) Motorcycle track alignment is the result of tests carried out under different riding conditions by our technical staff. Modifying factory setting is a very delicate operation, which may lead to serious damages if carried out by unskilled people. Before changing standard setting, measure the reference value (H, fig. 25). E The rider can modify track alignment according to his/her needs by changing working position of the shock absorber. fig.
UNIBALL articulated head (A) maximum extension is 5 threadings, i.e. 7.5 mm (B). B E A 30 fig.
DIRECTIONS FOR USE For all mechanical moving parts of the motorcycle to adapt to one another and above all not to adversely affect the life of basic engine parts, it is advisable to avoid harsh accelerations and not to run the engine at high rpm for too long, especially uphill. Furthermore, the drive chain should be inspected frequently. Lubricate it as required.
After 2500 km After running-in, never exceed the following values during the motorcycle standard use: 10000 rpm. Strict observance of running-in recommendations will ensure longer engine life and reduce the likelihood of overhauls and tune-ups. E MIN-1 x1000 fig.
Pre-ride checks Warning Failure to carry out these checks before riding, may lead to motorcycle damage and injury to rider and passenger. Before riding, perform a thorough check-up on your bike as follows: Fuel level in the tank Check fuel level in the tank. Fill tank if needed (page 38). Engine oil level Check oil level in the sump through the sight glass. Top up with recommended oil if needed (page 57). Brake and clutch fluid Check fluid level in the relevant reservoirs.
Starting the engine N F O OF PUSH Note Follow the “High ambient temperature” procedure to start the engine when it is warm. ON Regular ambient temperature (10 °C/50 °F to 35 °C/95 °F): 1) Move the ignition key to ON (fig. 29). Make sure both the green light N and the red light on the instrument panel come on. Important The oil pressure light should go out a few seconds after the engine has started (page 11).
3) Check that the stop switch (3, fig. 31) is positioned to (RUN), then press the fast idle button (4). Let the engine start without using the throttle control. A B Important Never operate the electric start button more than 5 seconds at a time. If needed, allow 10 seconds before attempting to restart the engine. 4) Move the fast idle lever (1) to its vertical position (A) (fig. 30). E Important Do not rev up the engine when it is cold. Allow some time for oil to reach all points that need lubricating.
E Moving off 1) Disengage the clutch squeezing the control lever. 2) Push down on gear change lever sharply with the tip of your foot to engage the first gear. 3) Speed up engine, by turning the throttle twistgrip and slightly releasing the clutch lever at the same time. The motorcycle will start moving off. 4) Let go of clutch lever and speed up. 5) To shift to second gear, close the throttle to slow down engine, disengage the clutch right away, lift the gear change lever and let go of clutch lever.
Stopping the motorcycle If you let go of the throttle twistgrip, the motorcycle will slow down gradually and smoothly. Then, shift down releasing the clutch, and finally change from first to neutral. Apply brakes and you will bring the motorcycle to a complete stop. To switch the engine off, simply turn the key to OFF (page 13). E Important Never leave the key in the ON position when engine is stopped, or this will damage the electric components.
E Parking Stop and park the motorcycle on the side stand (see page 25). To avoid theft, turn the handlebar fully left and block it by turning the ignition key to the LOCK position. If you park in a garage or other facilities, make sure that there is proper ventilation and that the motorcycle is not near a source of heat. You may leave the parking lights on by turning the key to position P. Refueling (fig. 32) Never overfill the tank when refueling. Fuel should never be touching the rim of filler recess.
Tool kit and accessories (fig. 33) The compartment (1) under the tail guard holds: an Owner’s manual; a helmet fastening cable; a tool bag for usual maintenance and checks. To reach this compartment, the tail guard must be lifted by opening the catch (page 23). The tool bag (fig. 34) holds: 1)14-mm box wrench. 2)10/8/6/5/4-mm Allen wrench. 3) Rear eccentric wrench. 4) Front wheel shaft wrench. 5) Extension for rear eccentric wrench. 6) Box wrench for spark plugs. 7) Tommy bar. 8) Double-bit screwdriver.
MAIN MAINTENANCE OPERATIONS E Side body panels (fig. 40) To remove the body panels proceed as follows: disconnect the two connectors (1) joining the two body panels together; disconnect the four headlamp fairing connectors (2); disconnect the four frame connectors (3). Removing the fairing Some servicing operations need the motorcycle fairing to be removed.
Headlamp fairing (fig. 42) Undo the middle fastening screw (1, fig. 41) of the wing mirrors and remove them from the headlamp fairing supports. Undo the two fastening screws (2) of the headlight support and disconnect the four connectors (3) joining the two body panels together. Important At reassembly, apply “medium-strength threadlocker” onto the screw threading (1). E 1 fig. 36 2 3 fig.
Cleaning and changing air filters (fig. 39) Note To make the procedure clearer, complete air box is shown in the exploded view (fig. 39). Remove parts indicated in the following description only. E The air box is accessible after removing the body panels and the headlamp fairing (see pages 40 and 41). Undo the eight fastening screws of the outer cover (1, fig. 38). Remove the cover but leave it hanging from the turn indicator cable. Do not remove the reduction element (4) from its seat. 1 fig.
Remove the filter (2, fig. 39) from its seat on the inner cover (3). Clean the filter cartridge with compressed air or fit a new one, if needed. 4 1 Important A dirty filter will reduce air intake, increase fuel consumption, reduce engine power, and foul the spark plugs. Do not use the motorcycle without filter or suspended matters could get into the engine and cause damage. E 3 Install the filter properly into its seat on the inner cover and refit all the parts you have removed. 2 fig.
E Checking the coolant level (fig. 40) Check the coolant level in the expansion reservoir, on the LH side of the motorcycle. The coolant level must be between the MAX and MIN marks. Top up if the level is too low. Remove the l.h. body panel and the fuel tank. Lift the tail guard and undo the rear screw (2, fig. 41). Remove the tank from its front clamping by pulling the tank backwards. Move it to the right leaving fuel tubing connected. Unscrew the filler (1, fig.
Checking brake and clutch fluid level Fluid level should never fall below the MIN mark on each reservoir (fig. 42). If level drops below the limit, air might get into the circuit and affect the operation of the system involved. Brake and clutch fluid must be topped up and changed at the intervals specified in the routine maintenance chart (see Warranty Card) by a Ducati Dealer or Authorized Workshop. Important It is recommended all brake and clutch tubes be changed every four years.
Checking brake pads for wear (fig. 43) To facilitate inspection without removing the pads from the calipers, brake pads have a wear mark. If the grooves in the friction material are still visible, the pad is still in good condition. MIN Important Have the brake pads replaced at a Ducati Dealer or Authorized Workshop. E fig.
Lubricating cables and joints The condition of the outer sheath of the throttle/cold start cable should be checked at regular intervals. The sheath should show no signs of squeezing or cracking. Work the controls to make sure the cable slides smoothly inside the sheath: if you feel any friction or hard spots, have the cable replaced by a Ducati Dealer or Authorized Workshop. To prevent these failures, smear the end of the Bowden cable with SHELL Advance Grease or Retinax LX2 at regular intervals.
Charging the battery (fig. 45) Before charging the battery, it is best to remove it from the motorcycle. Remove the r.h. body panel (page 40), undo the screw (1) and remove the upper bracket. Always disconnect the black negative terminal (-) first, and then the red positive terminal (+). E Warning Keep the battery out of the reach of children. Charge the battery at 1 A for 5-10 hours. Warning Batteries develop explosive gases: keep it away from heat sources and flames.
Adjusting headstock angle (fig. 46) Loosen the two screws (1) on the frame r.h. side to adjust the headstock angle. Fully unscrew the screw (2) and turn the steering tube end (3) by 180° with a pin wrench. Check that the hole on the eccentric is centred with the through hole in the steering tube. Look at the arrow etched in the top area of the eccentric to centre both holes accurately. Fully screw the screw (2). Grease the screw threadings (1) with SHELL Retinax HDX2 and tighten to 22 Nm.
Chain tension inspection (fig. 48) With the motorcycle on the side stand, the chain must have a min. distance of 25 mm from the swingarm. If this is not the case, contact a Ducati Dealer or Authorized Workshop for proper chain tensioning. Tensione catena (sul cavalletto laterale) Chain tension adjustment (on side stand) Warning Correct tightening of the eccentric hub clamping screws is essential to rider and pillion passenger’s safety.
Replacing bulbs Before replacing a burnt-out bulb, make sure that the new one complies with voltage and wattage as specified on page 68, “Electric System”, for that lighting device. Always check for new bulb proper operation before refitting removed parts. Headlamp To gain access to headlamp bulbs proceed as follows: Disassembly: low beam bulb (fig. 49): remove the rubber cover (1). Press the lower quick-release button to disconnect the connector (2). L.h. high beam bulb (fig.
Note Be careful to hold the new bulb at the base only. Never touch the transparent body with your fingers or it will blacken resulting in reduced bulb brilliancy. E Reassembly: insert the locating pegs of the bulb base into their seats to obtain correct alignment. Hook the clip (4, fig. 50) to the headlamp holders; reconnect the cables and refit the rubber cover (1, fig. 50). To change the two parking light bulbs, the headlamp fairing must be removed first (see page 41).
Turn indicators (fig. 53) Remove the screw (1) and detach the glass (2) from the body. The bulb is of the bayonet-type: press and rotate anticlockwise to remove; fit the spare bulb by pressing and turning clockwise until it clicks. Refit the glass sliding the small tab (A) into the suitable slot in the indicator body and tighten the screw (1). A 2 1 E fig. 53 Stop light (fig. 54) To replace the stop and parking light bulb, lift the tail guard and unscrew the two screws (1) that secure the glass (2).
Number plate light (fig. 55) To expose the number plate light bulb, withdraw the lamp holder from the number plate holder, then extract the bulb and replace it. E Beam setting (fig. 56) When checking the beam setting, put the motorcycle upright. Tyres should be inflated at the correct pressure and one person should be sitting astride the motorcycle, keeping it at right angles to its longitudinal axis.
Rear view mirror adjustment (fig. 57) Using a cross-section screwdriver, undo the screw (2), manually adjust the mirror and tighten the screws. 9 x 10 x 10 m fig. 56 Tubeless tyres Tyre pressure Front: 2.1 bar - 2.3 Kg/sq cm Rear: 2.2 bar - 2.4 Kg/sq cm E As tyre pressure is affected by temperature and altitude variations, you are advised to check and adjust it whenever you are riding in areas where ample variations in temperature or altitude occur.
Tyre repair or replacement (Tubeless) In the event of a tiny puncture, tubeless tyres will take a long time to deflate, as they tend to keep air inside. If you find low pressure on one tyre, check the tyre for punctures. E Warning A tyre must be replaced when punctured. Replace tyres with recommended standard tyres only. Be sure to tighten the valve caps securely to avoid leaks when riding. Never use tube type tyres.
Checking engine oil level (fig. 59) Engine oil level can be checked through the sight glass (1) provided on the clutch cover. When checking oil level, the motorcycle should be upright and the engine cold. Oil level should be between the marks near the sight glass. Top up oil level with SHELL Advance Ultra 4, if low. Undo the filler plug (2) and top up to correct level. Refit the plug.
E Cleaning and replacing the spark plugs (fig. 60) Spark plugs are essential to smooth engine running and should be checked at regular intervals. This is done quite easily and quickly and provides a good measure of engine condition. Remove the l.h. body panel, remove the spark plug caps and spark plugs from the cylinder head using the wrench supplied with the motorcycle.
Cleaning the motorcycle To preserve the finish of metal parts and paintwork, wash and clean your motorcycle at regular intervals, anyway according to the road conditions you ride in. Use specific products only. Prefer biodegradable products. Avoid aggressive detergents or solvents. Never grease or lubricate the brake discs. Loss of braking and further accidents may occur. Clean the discs with an oil-free solvent. Important Do not wash your motorcycle right after use.
E Storing the bike away If the motorcycle is to be left unridden over long periods, it is advisable to carry out the following operations before storing it away: clean the motorcycle; remove tank drain plug and seal and drain all fuel from tank; pour a few drops of engine oil into the cylinders through the spark plug seats, then crank the engine by hand a few times so a protective film of oil will spread on cylinder inner walls; place the motorcycle on the paddock stand; disconnect and remove the battery.
TECHNICAL DATA Overall dimensions (mm) (fig. 61) Weights Dry weight: 198 Kg. Carrying full load: 375 Kg. Warning Failure to observe weight limits could result in poor handling and impair the performance of your motorcycle, and you may lose control of the motorcycle. fig.
Top-ups Type of fluid cu dm (liters) Fuel tank, including a reserve of 4 cu dm (liters) Gasoline 95-98 RON 17 Oil sump and oil filter SHELL - Advance Ultra 4 3.7 Front/Rear brake and clutch circuits Special fluid for hydraulic systems SHELL - Advance Brake DOT 4 _ Protectant for electric contacts Spray for electric systems SHELL - Advance Contact Cleaner _ Front fork SHELL - Advance Fork 7.5 or Donax TA 0.
Engine Twin cylinder, four-stroke, 90° “L” type, longitudinal. Bore mm: 100 Stroke mm: 63.5 Total displacement cu.cm.: 998 Compression ratio: 1:11.4±0.5 Max. power at crankshaft (95/1/EC): 167 kW -(123 HP) at 9750 rpm Max torque at crankshaft (95/1/EC): 9.89 Kgm at 8000 rpm Max. rotation speed: 11500 rpm Desmodromic timing system (fig. 62) 1) Opening (or upper) rocker. 2) Opening rocker shim. 3) Closing (or lower) rocker shim. 4) Return spring for lower rocker. 5) Closing (or lower) rocker. 6) Camshaft.
Performance data Maximum speed in any gear should be reached only after a correct running-in period with the motorcycle properly serviced at the recommended intervals. Max. speed (rider alone): 270 Km/h E Spark plugs Make: CHAMPION Type: RG 4 HC Brakes Front brake With double floating drilled disc. Material: steel Disc diameter: 320 mm Hydraulically operated by a control lever on right handlebar. Braking surface: 88 sq cm Brake calipers with separate pistons. Make: BREMBO 64 Type: 30/34-4 pistons.
Transmission Dry clutch operated by a control lever on left handlebar. Drive is transmitted from engine to gearbox main shaft via spur gears. Gear ratio: 32/59 6-speed gearbox with constant mesh gears, gear change pedal on left side of motorcycle. Front/rear sprocket ratio: 15/36 Total gear ratios: 1st gear 15/37 2nd gear 17/30 3rd gear 20/28 4th gear 22/26 5th gear 23/24 6th gear 24/23 Important The above gear ratios are the homologated ones and under no circumstances must they be modified.
Frame Tubular trestle frame with upper section made of highstrength steel. Steering angle (on each side): 27° For improved performance on track the headstock angle can be changed (see page 49). E STANDARD steering setting for road riding is as follows: Steering head angle: 24°30’ Trail: 97 mm. For track riding, setting can be modified to the following values: Steering head angle: 23° 30’ Trail: 91 mm. Wheels Five-spoke, light-alloy rims. Front wheel Dimensions: 3.50x17" Rear wheel Dimensions: 5.
Suspensions Available colours Front Hydraulic upside-down fork provided with outer adjuster for rebound, compression, and preload (for inner springs of fork legs). Stanchion diameter: 43 mm Travel along leg axis: 127 mm. Available in: “Matrix” green *0030 (PPG); metal-color frame and wheel rims. E Rear Of the progressive type, thanks to a rocker arm connecting frame and upper pivot point of the shock absorber.
E Electric system Basic electric items are: front headlamp consisting of the following: 12V-55W low beam unit, poly-ellipsoidal with capacitor; 12V-55W high beam unit; parking light with no. 2 12V-5W bulbs. Instrument panel, 12V-1.2W warning lights; 12V-2W instrument lights. Electrical controls on handlebars. Turn indicators, 12V-10W bulbs. Horn. Stop light switches. Battery 12V-16Ah. Generator 12V-520W. Electronic voltage regulator (rectifier), protected by a 40 A fuse near the battery.
E fig. 63 fig. 65 3 IN GOOD CONDITION fig. 64 3 BLOWN fig.
E Legend of the wiring diagram of electric system/injection 1) Right switch 2) Key-operated switch 3) Ignition relay 4) Fuse box 5) Flasher 6) Water temperature sensor 7) RH electric fan 8) Starter motor 9) Solenoid starter 10) Battery 11) Regulator fuse 12) Regulator 13) Generator 14) Rear right-turn indicator 15) Tail light 16) Number plate lighting bulb 17) Rear left-turn indicator 18) Fuel tank 19) Diagnosis connector 20) Injection relay 21) Horizontal cylinder coil 22) Vertical cylinder coil 23) Horiz
Wire color coding P Pink G Green W White O Orange Y Yellow B Blue Bn Brown R Red V Violet Gr Grey Lb Light blue Bk Black Legend of fuse box (4) Pos. Description Rat. 1-9 Main switch 30 A 2-10 Fuel pump, injectors, coils 20 A 3-11 Key sense 7.5 A 4-12 CPU power supply 3A 5-13 High beam and low beam 15 A 6-14 Turn indicators, warning lights, parking lights and instrument panel lights 10 A 7-15 Stop, warning horn 7.5 A 8-16 Cooling electric fan 7.
FOR UNITED STATES OF AMERICA VERSION ONLY USA E Reporting of safety defects If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ducati North America. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Crankcase Emission Control System The engine is equipped with a closed crankcase system to prevent discharging crankcase emissions into the atmosphere. Blow-by gas is returned to the combustion chamber through the air cleaner and the throttle body. Evaporative Emission Control System California motorcycles are equipped with an evaporative emission control system which consists of a charcoal canister and associated piping. This system prevents the escape of fuel vapors from the throttle body and fuel tank.
USA E Riding safety The points given below are applicable for every day motorcycle use and shoud be carefully observed for safe and effective vehicle operation. A motorcycle does not provide the impact protection of an automobile, so defensive riding in addition to wearing protective apparel is extremely important. Do not let protective apparel give you a false sense of security. Before changing lanes, look over your shoulder to make sure the way is clear.
Warning Do not ride the motorcycle with helmets attached to the hook; the helmets could cause an accident by distracting the operator or interfering with normal vehicle operation. The exhaust system becomes very hot during operation, never touch the exhaust system. Wear clothing that fully covers your legs. Do not wear loose clothing which could catch on the control levers, footrests, wheels, or chain. Any amount of alcohol will significantly interfere with your ability to safely operate your motorcycle.
Label location (fig. B) 1 7 10 6 USA E 11 2 2 76 4 3 5 8 9 fig.
WARNING Manufactured by OBJECTS IN MIRROR ARE CLOSER THAN THEY APPEAR 2 DO NOT ATTEMPT TO LOOK THROUGH THIS FAIRING. THIS IS NOT A WINDSHIELD, BUT AN AERODYNAMIC FAIRING ONLY; FAILURE TO OBSERVE THIS WARNING COULD RESULT IN A COLLISION OR UPSET AND CONSEQUENT SERIOUS BODILY INJURY. Cod. 433 1 165 1A 1 DATE: 07/97 GVWR: 925.9 Lbs (420 kg) GAWR front: 319.7 Lbs (145 kg) with 120/70ZR17 tire, MT 3.50x17 RIM at 32.7 PSI cold. GAWR rear: 606.2 Lbs (275 kg) with 170/60ZR17 tire, MT 5.50x17 RIM at 36.
California evaporation emission system This system consists of (fig. C): 1) Warm air inlet; 2) Canister; 3) Dell’Orto jet; 4) Fuel tank; c) Breather pipe; d) Drain pipe. Important In the event of fuel system malfunction, contact Ducati’s authorized Service Centres. 4 3 CANISTE R CANISTER USA E 1 fig. C 78 2 c d c Ducati limited warranty on emission control system Ducati North America, Inc.
parts replaced and labor charges based on Ducati’s recommended time allowance for the warranty repair and the geographically appropriate hourly labor rate. The owner may be required to keep receipts and failed parts in order to receive compensation. II. Limitations This Emission Control System Warranty shall not cover any of the following: A.
USA E transportation of the motorcycle to or from the Ducati dealer. Ducati shall not be liable for any other expenses, loss or damage, whether direct, incidental, consequential or exemplary arising in connection with the sale or use of or inability to use the Ducati motorcycle for any purpose. Some states do not allow the exclusion or limitation of any incidental or consequential damages, so the above limitations may not apply to you. B.
ROUTINE MAINTENANCE RECORD km Ducati Service Name Mileage Date 1000 10000 E USA 20000 30000 40000 50000 81
02 RUN OFF START W/R R G/Bk 03 G/R 04 LOCK W PARK R OFF 86 ON Y/B Bn 87 30 85 4 3 2 1 1 4 6 3 2 05 07 06 08 32 09 10 11 12 13 Y Bk 5 Y/B M 9 R 10 R 11 O/B 12 R 13 R/G 14 15 V/Bk 16 1 2 3 4 5 6 7 8 B/Bk Gr O R 2 1 R/Bk R + Lb 40A - 01 2 1 Y Y Y Bn R/Bk R R/Bk G/Gr Bk Bk R Bk W/G R 14 10 W Bk G/W R/Bk 44 Y/B 10 W R/B Bn/G Y W O/G 5/21 W Bk Bk R O Gr/R Bk Bk Y W/G Y Bk W/Bk 2 3 1 15 3 1 2 4 5/21 W W/G 55W A B Y C 43
