User's Manual

ManualsBrandsDuali ManualsElectronicsSMART CARD READER

document in part or as a whole for any purposes other than those for which this document is disclosed. This document

is copyrighted and contains confidential information and other intellectual property rights of DUALi Inc. An

unauthorized use, copy, disclosure or distribution constitutes infringement of DUALi’s intellectual property rights.

DUALi Inc.

Document Number: EP01-14-004

Document Version: 1.0

Last Revised Date: 11

Dec. 2014

ITOUCH_POP2

Specification

Summary of content (18 pages)

PAGE 1
ITOUCH_POP2 Specification DUALi Inc. Document Number: EP01-14-004 Document Version: 1.0 Last Revised Date: 11th Dec. 2014 Copyright ⓒ 2014 DUALi Inc. All rights reserved. You are strictly prohibited to copy, disclose, distribute, or use this document in part or as a whole for any purposes other than those for which this document is disclosed. This document is copyrighted and contains confidential information and other intellectual property rights of DUALi Inc.
PAGE 2
FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: SWUITOUCHPOPV2 WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
PAGE 3
DUALi Inc. reserves the right to make changes to its applications or services or to discontinue any application or service at any time without notice. DUALi provides customer assistance in various technical areas, but does not have full access to data concerning the use and applications of customer's products. Therefore, DUALi assumes no liability and is not responsible for customer applications or software design or performance relating to systems or applications incorporating DUALi products.
PAGE 4
iTOUCH_POP2 Product Specification ` Revision History  Version. 1.0 2014.12.11 (Ver. 1.0) : Release 3 DUALi Inc. (http://www.duali.
PAGE 5
iTOUCH_POP2 Product Specification ` Contents 1 Introduction............................................................................................................................... 5 2 Components Confirmation ......................................................................................................... 6 3 4 5 6 2.1 Product Components....................................................................................................... 6 2.2 Block Diagram .......................
PAGE 6
iTOUCH_POP2 Product Specification ` 1 Introduction iTOUCH pop2 is designed as a wall-mounted smartcard reader suitable for time-attendance, access control, ID check, self-check-in, self-payment system based on Android O/S. iTOUCH pop2 communicates with PC or controller via USB ,TCP/IP, WiFi(wireless LAN) or Bluetooth(option). User can develop their own program by using Android Jellybean CPU 32bit ARM-CORTEX A5 RISC processor Operating frequency Normal.
PAGE 7
iTOUCH_POP2 Product Specification ` Wireless LAN Module WIFI IEEE 802.11n/e/i standards up to 150Mbps Operating Powers Option Min 9V, Max 28V (12V DC adaptor) 2 Components Confirmation 2.1 Product Components ① ② ③ ① Reader unit ② WALL Fixer Bracket ③ Screw (2.5*4 / 4 EA) ④ Cable (Provide as your favor) 1) Door cable 2) Wiegand cable 3) PWR cable 4) RS-232 cable 5) RS-485 cable ⑤ 12V DC adaptor  Version. 1.0 Please use the approved adapter that satisfies the LPS 6 DUALi Inc.
PAGE 8
iTOUCH_POP2 Product Specification ` 2.2 Block Diagram TFT LCD(4.3”) WIFI USB HUB 1677 Color Touch pad USB Host USB OTG CAMERA Module Ethernet DDR3 (1GByte) Nand Flash (4GByte) RS-485 32bit ARM Micro SD CARD RS-232 Cortex-A5 RISC KEYPAD (4ea) RS-232 Processor DOOR I/F Battery Wiegand RF/SAM Module PN512 SAM Card *1 Version. 1.0 7 DC/DC DC INPUT CONVERTER (9V~28V) Sound Codecs Speaker DUALi Inc. (http://www.duali.
PAGE 9
iTOUCH_POP2 Product Specification ` 2.3 Block Diagram specification  CPU: ARM CORTEX 32-bit A5 RISC processor TCC8925  Program & Data Memory: NAND Flash 4Gbyte for program running & file system.  Operation Memory: 1Gbyte DDR3 SDRAM for rapid operating process  LCD: Wide 4.3-inch (16.7M Color TFT LCD) with Touch panel.  Camera: Includes Auto Focus and LED for light  Speaker: 1W / 8ohm speaker is embedded.
PAGE 10
iTOUCH_POP2 Product Specification ` 2.4 Exterior < Front > < Rear > Version. 1.0 9 DUALi Inc. (http://www.duali.
PAGE 11
iTOUCH_POP2 Product Specification ` 2.5 PCB - MAIN Board SD Card Speaker CAMERA Ethernet Board RS-232 SAM Door Control RS-485 Wiegand Debug USB Host DC 12V USB Slave FLASH LED LCD KEY 4EA Version. 1.0 10 DUALi Inc. (http://www.duali.
PAGE 12
iTOUCH_POP2 Product Specification ` - LAN Board RF Board - 2.6 Product Size - ITOUCH_POP2 (mm) : 185(W) *108(H) * 20.5(D) - Thickness (PCB) MAIN Board : 1.0T RF Board : 1.0T LAN Board : 1.0T Version. 1.0 11 DUALi Inc. (http://www.duali.
PAGE 13
iTOUCH_POP2 Product Specification ` 3 Power & Interface Specification 3.1 Power Specification - 12V : 1.5A or above - 24V : 700mA or above 3.2 Electric Current Specification - 12V : average 400mA - 12V : Max 550mA 3.3 RS-232 Interface Specification - 8 Data, 1 Stop, No Parity - Communication speed: Start with 115200 bps 3.4 USB Interface Specification - 3.5 TCP/IP Interface Specification - 3.6 10B / 100B both supported WI-FI Interface Specification - Version. 1.0 USB 1.
PAGE 14
iTOUCH_POP2 Product Specification ` 4 Configuration for Door Lock Control 4.1 POP + LOCK J9 – DOOR PIN 1 2 3 Specification RELAY Normal Close Normal Open RELAY COMMOM Door SW 5 GND 7 SENSOR RELAY 4 6 EXIT LOCK DOOR STATUS GND Normal Close Type LOCK DC+ (12V or 24V) PWR GND LOCK COMMON CONNECTION NORMAL OPEN LOCK(Secure, open when powered) NORMAL CLOSE LOCK(Safe, close when powered) Version. 1.0 13 DUALi Inc. (http://www.duali.
PAGE 15
iTOUCH_POP2 Product Specification ` 4.2 POP + PDU + Deadbolt Lock 4.3 POP(RS-485) + PDU + Deadbolt Lock Version. 1.0 14 DUALi Inc. (http://www.duali.
PAGE 16
iTOUCH_POP2 Product Specification ` 5 Connector Specification 5.1 J6 (MINI USB) – USB_OTG (Outside) PIN 5.2 Specification 1 USB 5.0V 2 USB D- 3 USB D+ 4 ID 5 GND 5V not available J17 (USB A TYPE) – USB_HOST (Outside) PIN 5.3 Specification 1 VDD 5.0V 2 USB D- 3 USB D+ 4 GND Description J8 (2mm ,3-PIN DIP TYPE, RIGHT Angle) – UART - 20017WR-03 (YEONHO) PIN 5.4 Specification 1 RS-232 TXD 2 RS-232 RXD 3 GND Description J7 (1.
PAGE 17
iTOUCH_POP2 Product Specification ` 5.5 J9 (2mm ,4-PIN DIP TYPE, RIGHT Angle) - RS-485 (Outside) - 20017WR-04 (YEONHO) PIN 5.6 Specification 1 RS-485 + 2 RS-485 - 3 Terminating resisters Resistor 4 Terminating resisters Resistor J11 (2mm, 7-PIN DIP TYPE, RIGHT Angle) - DOOR (Outside) - 20017WR-07 (YEONHO) PIN 5.
PAGE 18
iTOUCH_POP2 Product Specification ` 6 Usage Environment 6.1 Recommendable Operating Environment - Temperature: -10 ~ 60 ℃ - Humidity: 30 ~ 90 % 6.2 Recommendable Storage Environment - Temperature: -20 ~ 80 ℃ - Humidity: 30 ~ 90 % 7 Warning and Notice - Indoor use only (Avoid direct sunlight) - Recommended to use 12V, 700mA or above Diameter = 2mm DC + Diameter = 6.