ALB10 INSTALLATION/OWNER'S MANUAL 10" Ported Enclosure with Built-in Amplifier
PREPARATION Getting Started Thank you for purchasing the Dual ALB10 10" ported enclosure with built-in amplifier. Although Dual has attempted to ensure the information in this manual is accurate, please be aware that any part of it is subject to change without notice. Please read entire manual before installation. Due to the technical nature of amplifiers, it is highly recommended that your Dual ALB10 is installed by a professional installer or an authorized dealer.
INSTALLATION Safety First ! CAUTION The following instructions are designed to ensure safety during installation and use of the ALB10. Failure to heed these instructions can result in injury or damage to the unit or vehicle. The following installation instructions are intended to be used as a basic guideline. If you feel unsure about installing this speaker system yourself, Dual recommends acquiring the services of a professional car audio installation center.
INSTALLATION Connection Descriptions Note: Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used a general guideline only. Power Wire (+12V) • Disconnect negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • Plan wire routing before cutting any wires to length. Begin by routing the power +12V wire from the battery to the amplifier location.
INSTALLATION Connections and Controls 1 2 3 4 5 6 7 8 9 10 11 1 Hi-Level Inputs 7 Power Indicator 2 Line In (Left) 8 Ground Connection 3 Line In (Right) 9 Remote Connection 4 Crossover Frequency 10 Power Connection 5 Input Level Control 11 Fuse (15A) 6 Phase Control 5
INSTALLATION Typical Wire Routing 18” MAXIMUM BATTERY HIGH LEVEL INPUT (SPEAKER WIRE) High Level Input (Speaker Wire) High level inputs should only be used when RCA outputs are not available from the head unit. Connect the head unit speaker outputs to the high level input connector as shown below. The black wire (signal reference ground) may or may not require a connection to chassis ground - depending on your particular installation. Do not use both low and high level inputs at the same time.
INSTALLATION Control Setup and Adjustment Input Signal Connections Low Level (RCA) Crossover Frequency Control Phase Control Low level (RCA) input signal is preferred for best performance. Typical trunk-mount installations require a 17-20 foot RCA cable. Most trucks and behind-seat applications require a 6-12 foot RCA cable. Using twisted pair construction RCA cables will minimize noise. The adjustable crossover is used to filter out frequencies above 40Hz ~ 160Hz.
INSTALLATION Troubleshooting Problem Cause Unit will not turn on (no power LED indicator) BAT+ wire not connected or incorrect voltage REM wire not connected or incorrect voltage Check connections for proper voltage (11~16VDC) GND wire not connected Check connection to ground Fuse(s) blown Replace fuse(s) Volume turned all the way down Increase volume level at head unit Speaker defective or damaged Check/replace speaker Input signal not connected Check high or low level inputs for proper conn
WARRANTY Limited One-Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp.
INSTALLATION Notes For Your Records Please keep your original sales receipt and be prepared to provide this receipt in the event you require service, as your original receipt is considered the best proof of purchase and indicates the date you purchased your Dual product. Dealer Name Dealer Phone Purchase Date Register Your Product 10 Register your product online at www.dualav.
INSTALLATION Specifications Maximum Output Power 300 watts Continuous Output Power 100 watts Frequency Response 20-200Hz S/N Ratio @ 1 watt Input Impedance 85dB Low level (RCA): 10k ohms Input Sensitivity (RCA) 50mV – 3V Crossover Frequency 40–160Hz Crossover Slope Phase Fuse Dimensions 6dB/octave 0–180 degrees 15 amp ATO 12.6" x 16.5" x 9.8" (HxWxD) Design and specifications subject to change without notice.
Dual Electronics Corp. Toll Free: 1-866-382-5476 Monday-Friday, 9AM-5PM EST www.dualav.com ©2013 Dual Electronics Corp. All rights reserved.
