Palladium II Digital COFDM Transmitter Model Pd2-TX-1000 1W Output The most important thing we build is trust
how to contact COBHAM copyright notice For operator and troubleshooting information, customers are encouraged to refer to the details in this manual. For additional clarification or instruction, or to order parts, contact COBHAM. Copyright © 2011 Customer Service is available Monday through Friday between the hours of 9:00 AM and 5:00 PM EST at: Tel: 603-880-4411 Fax: 603-880-6965 Website: www.cobham.com/tcs Email: dtc.info@cobham.com DTC Communications, Inc.
TABLE OF CONTENTS manual conventions NOTE: Describes special issues you should be aware of while using a particular function. WARNING: Calls out situations in which equipment could be damaged or a process could be incorrectly implemented, but in which operator safety is not a factor. TIP: Describes application hints. RF EXPOSURE STATEMENT Quick Start .....................................................................................................................4-5 Accessories ........................
QUICK START Complete these steps: A1 R/M 2 A2 L 3 Palladium Transmitter, Top View Came ra 1. Connect the transmitter antenna to the SMA connector on the Palladium unit. 2. If you plan to use audio, connect one or two microphones to the Audio 1 and/or Audio 2 LEMO connectors. If using monaural, use Audio 1. 3. Connect power and video input via the Multi I/O cable to the 6-pin Hirose connector: a.
QUICK START 4 4 Set to the required configuration as indicated by the channel numbers. Refer to the Programming section on page 10 for more information on channel settings. Your Transmitter is now operational. Confirm its signal with your Palladium Receiver. Accessories • 12 VDC 2.5A Power Supply & AC Line Cord • Microphone, Body-Worn, (2) • Power & Video Cable • Camera Power Cable (2.
INTRODUCTION Palladium II The Palladium II Series of digital video transmitters provide exceptional video quality in high multipath environments. They are ideal for use inside buildings, in urban areas, and in other applications where multipath would normally cause video tearing or breakup. All Palladium II Series transmitters offer three bandwidth modes: DVB-T (6, 7, 8 MHz), Narrow (2.5 MHz), and Ultra Narrow (1.25 MHz) channel spacing.
OPERATION Using your Palladium II Transmitter Follow the instructions given in the Quick Start section on pages 4-5. When power is first applied to the Palladium, the unit reverts to the indicated channel and RF ON state. The Alarm LED may be ON, which indicates that there is no active video input. Changing your Transmitter Configuration The Palladium Transmitter can store up to 8 different configurations, which can be selected with the Channel Control.
HEAT SINK 2.530 3.
HEAT SINK Palladium 1000 Heat Sink The Palladium 1000 is supplied with a heat sink attached. DO NOT remove the heat sink unless you have an alternate mounting surface that will dissipate the heat properly. WARNING: The Palladium 1000 may become too hot to touch without a proper heatsink attached, such as the one supplied. Damage to internal components may occur if operated beyond the recommended temperature range. If placed in an enclosure, proper ventilation and mounting is required.
COMPONENTS Controls/Connectors Data Chaining & Control Connector This connector is normally covered. Multi-I/O Connector The Multi-I/O Connector is covered on page 11. Audio 2 (left) and Audio 1 (right/mono) LEMO Conn. These connectors provide the audio input connections to the transmitter. Either one or two audio inputs can be used with the Palladium II Transmitter. ALARM LED This red LED indicates a valid video signal is not present.
COMPONENTS and PROGRAMMING Transmitter Antenna Connector (SMA) This connector attaches to the transmitter antenna and carries the RF output signal. Always ensure the transmitter antenna is attached before operating the Palladium Transmitter. Video In 75 Ohm 6 Muiti I/O Connector (6-pin Hirose) This connector provides connections for the DC Power Input, DC Camera Power, Programming, and 75 Ohm Composite Video Signal.
SPECIFICATIONS 12 Physical Unit Dimensions not including heatsink or connectors (approx.) Unit Dimensions including heatsink and connectors (approx.) 4.25” x 2.75” x 1.25” (10.8 cm x 7.0 cm x 3.2 cm) 4.75” x 2.75” x 2.5” (10.8 cm x 7.0 cm x 6.3 cm) Weight Weight without heatsink Weight including heatsink 9 oz (0.26 kg) 1 lb 3 oz (0.54 kg) Environmental Operational Temp -10 degrees C to 50 degrees C Power Input Voltage Power Consumption 10 to 16 VDC Fully Operational ~ 29 W max.
SPECIFICATIONS Video Bitrates Video Latency 1Mbps to 10 Mbps End to end delay of 54 milliseconds Audio Encoding Input Bitrates Sampling Frequency THD Response Crosstalk S/N Stereo or Dual Mono pair 28 kbps to 72 kbps depending on configuration 32 kHz, 16 kHz or 8kHz < 0.1% max 20Hz to 15KHz, +/- 0.
NOTES
CONTACT US Contact Information Toll-Free 1 800 233 8639 North America Sales/Training Office 2303 Dulles Station, suite 200 Herndon VA 20171 East Coast Offices 486 Amherst St.
Cobham Tactical Communications and Surveillance 486 Amherst Street • Nashua, New Hampshire 03063 • 603-880- 4411 www.cobham.
