PB-5 Beacon T ransmitter Transmitter Operator Manual DTC COMMUNICATIONS INCORPORATED OP1920148 Rev B
Copyright Notice Warranty For operator and troubleshooting information, customers are encouraged to refer to the details in this manual. For additional clarification or instruction, or to order parts, contact DTC. Customer Service is available Monday through Friday between the hours of 9:00 AM and 5:00 PM EST at: Tel: 603-880-4411 Fax: 603-880-6965 Website: www.dtccom.com Email: info@dtccom.com Copyright © 2002 DTC Communications, Inc. All rights reserved.
Manual Conventions NOTE Describes special issues you should be aware of while using a particular function. WARNING Calls out situations in which equipment could be damaged or a process could be incorrectly implemented, but in which operator safety is not a factor. TIP Describes application hints. TABLE OF CONTENTS Overview ............................................................................. 5 Connections ........................................................................ 7 Quick Start ......
TWO YEAR WARRANTY DTC Communications, Inc. (DTC) warrants its RF transmitting and receiving products to be free from defects in workmanship or material for a period of two (2) years from the date of shipment unless otherwise stated. The liability of DTC, Inc.
OVERVIEW INTRODUCTION The PB-5 is a reliable, fully synthesized, user programmable, one watt, package beacon. It has a number of unique features. Two modes of operation allow you to track or monitor a package using a DTC TRAK/R system or a VHF-FM receiver, Tracker mode and Event mode. The beacon’s two primary connections are the break wire and the standby wire. When the break wire is broken the alarm is activated, which is transmitted to the receiver.
OVERVIEW EVENT MODE While in Event mode, the PB-5 transmits confidence tones at a default rate of 30 second intervals. When the Break Wire is broken (circuit is opened), the PB-5 will alert the agent that the package or door has been opened. The PB-5 quickly changes the tone transmission to the easily recognized alarm signal. The alarm signal transmits twice per second. BREAK WIRE INPUT The break wire input on the PB-5 will detect a change-of-state.
Test Push-button Holding this push-button, while powering up, causes the unit to go into test mode. Based on the break wire and standby wire inputs, the unit will go into one of the four transmit modes. Break wire Standby wire Transmit Output None None In In None In None In Continuous Tone Continuous Tone Tracking Pulses Unmodulated Carrier Init Push-button Holding the init switch for one second, re-initializes the unit.
QUICK START PB-5 Beacon Transmitter What should you expect to receive with your PB5 Beacon Transmitter? 1 PB-5 Beacon Transmitter 1 Antenna 1 Screwdriver 1 DTC programming software package 1 DTC programming cable 2 Battery Pack with batteries 1 Test Cable OPTIONAL ACCESSORIES Part Number Description 4044359 Antenna 4045163 8002025 8 Part Number Description 8590093 Battery Holder for 4 AA batteries 8590094 Battery Snap with flying leads 4044348 Test Cable, MMCX to BNC Programming Cable Pro
1 2 3 4 5 6 7 QUICK START Connect an antenna to the RF Output connector on the transmitter. Connect the break wire and or standby wire depending on the desired configuration. Using the supplied screwdriver, turn the channel selector to the correct channel number. Connect the power source to the PB-5’s power terminals. If standby wire is used the PB-5 will not be enabled until the wire is removed. You will have to remove the wire to activate.
SPECIFICATIONS Specifications for the PB-5 Transmitter Dimensions Controls and Indicators Connectors Frequency Stability RF Output power into a 50 Ohm load Channel Capacity Frequency Range Modulation Modes 10 Spurious & Harmonic Attenuation Transmitter side-band suppression AM Hum and Noise attenuation FM Hum and Noise attenuation Operating Temp. Range Operating Voltage Range DTC COMMUNICATIONS, INC. 5.0” L x 1.2” W x 0.
Specifications for the PB-5 Transmitter RF Output Load-stability Weight Power Source Battery Life Current Drain NVRam settings (Default) SPECIFICATIONS Stable into a VSWR of 8 to 1 or better 1.6 ounces (less batteries) Four AA batteries (external) Four AA batteries (Duracell MN1500 rated at 2450 mAH) will transmit in confidence mode for more than 400 hours. • Standby: 200 uA Max • Active Transmit: 350 mA peak (1.
PROGRAMMING Introduction When you order a PB-5 Beacon transmitter, DTC will factory program your frequencies at no additional charge to you. This is often the best path for state and local agencies with limited frequencies available to them. DTC will also provide you with free software and a free programming cable, enabling you to change your frequencies. This is ideal if you often work with other agencies, or anticipate the equipment being used by a multi-jurisdictional task force.
Installing DTC Universal Programming Software on your PC PROGRAMMING NOTE: Uninstall any previous versions by going to Add/Remove Programs, clicking on DTC Universal Programming, and clicking on uninstall. 1 Click on Start, click on run. 2 Click on the Browse button. 3 Click on or find your CD drive. 4 Install the JAVA Runtime Environment Application first (CD provided). 5 Follow the install wizard screens. 6 Install the Universal Programming software next (floppy provided).
PROGRAMMING 1 2 Serial Port of computer: COM1 or COM2 Antenna POWER 14 DTC COMMUNICATIONS, INC. Connect the antenna to the PB-5. Install the programming cable into the RS232 connector on the PB-5. 3 Plug the serial cable of the programming cable into the COM1 or COM2 port of your computer. 4 Select Start, programs, DTC communications on your computer. 5 The system allows you to select device COM1 or COM2, depending on which serial port you are connected to. The cycle power screen displays.
PROGRAMMING The programming software returns to the TX screen with your new settings displayed, and an asterick (*) beside the channel that has changed. 11 Click on the upload button. A message screen displays the new settings being uploaded to device. A message screen displays that your settings have been successfully uploaded. Your new settings have been installed. 5 DTC COMMUNICATIONS, INC.
486 Amherst Street • Nashua, New Hampshire 03063 • 603-880-4411 www.dtccom.