Introduction DSC Security Products has made a multimillion dollar investment into the wireless security market. The Marquis System will be the first of many products to revolutionize the wireless security industry.
Chapter 1: Overview Chapter 1: Overview 1 A: Glossary Several terms are used throughout this manual to refer to parts and operations of the WLS900 System. Read the definitions below to familiarize yourself with the system and its terms. Access Code The 4-digit code entered by a user to arm or disarm the system. Up to 10 personal Access Codes may be programmed for different users. Backplate The mounting bracket used to secure each part of the WLS900 System to the wall.
Chapter 1: Overview OVERVIEW 1 B: Components Controller The Controller contains the system’s main electronics, RF receiver, communicator and back-up battery. The Controller is connected to an AC outlet and the telephone line. The Controller requires: • AC Adaptor labelled “Controller” • One 6V 1.
Chapter 1: Overview Universal Transmitter WLS905 WLS907 The WLS905 and WLS907 Universal Transmitters are general purpose detection devices that may be used as door or window contacts. Universal Transmitters feature their own built-in contacts, and they may also be wired with external contacts.
Chapter 2: Getting Started Chapter 2: Getting Started Read Chapter One: Overview to familiarize yourself with the WLS900 System, its components, and the terms used in this manual. Chapter Two: Getting Started explains how to: • Prepare the system components for installation GETTING STARTED • Reset the system programming to the factory default settings • Install the battery in the Controller 2 A: Preparing for Installation Remove all Components from their packaging.
Chapter 2: Getting Started 2 B: Installing the Controller Battery Connect the 6V 1.2Ah battery. Be sure to connect the RED lead to the RED terminal, and the BLACK lead to the BLACK terminal. If the connection is made in reverse, the Controller will not be damaged, but the Controller will not function properly. Place the battery in the Controller case as shown below. CONTROLLER CIRCUIT BOARD CONTROLLER BATTERY CONTROLLER BATTERY SHOWN INSTALLED. BATTERY WIRES NOT SHOWN FOR CLARITY.
Chapter 3: Adding Components Chapter Three: Adding Components explains how to: • Add the first Keypad to the system • Enter the Enrollment Mode • Add components to the system • Review the list of components on the system • Remove components from the system Two sets of batteries are provided with the keypad. When programming the system, because of the length of time required, as well as the amount of communication that occurs between the keypad and controller, the life of the batteries may be reduced.
Chapter 3: Adding Components 3 B: Entering the Enrollment Mode ∗ Enter the Installer’s Programming Mode by entering [ ][8][Installer’s Code] (refer to Chapter 5A, How to Enter the Installer's Programming Mode.) -Yes Key when this message Press the is displayed. When this message is displayed, press the -YES Key.
Chapter 3: Adding Components 3 C: Enrolling Sounders Enter the Enrollment Mode as described in 3 B: Entering the Enrollment Mode Do not install batteries in the Sounder until the Sounder is ready to be mounted in its permanent location. ADDING COMPONENTS Plug the Sounder’s AC Adaptor into a wall outlet and plug the Adaptor into the Sounder AC Jack. A loud beep will sound. Enter the Sounder’s Serial Number on the keypad. -YES Key. The Sounder will Press the sound two short beeps.
Chapter 3: Adding Components 3 D: Enrolling Detection Devices As each detection device is enrolled it is assigned to the first available Zone. That is, the first device will be assigned to Zone 1, the second will be assigned to Zone 2, and so on. A maximum of 10 detection devices may be enrolled. Enter the Serial Number of the detection device to be enrolled. Press the -YES Key. The Sounders will sound two short beeps. Install the batteries in the detection device.
Chapter 3: Adding Components 3 E: Enrolling the Second Keypad Enter the Serial Number of the Second Keypad on the First Keypad. Press the -YES Key. The Sounders will sound two short beeps and this message will be displayed. Install the batteries in the Second Keypad. Refer to the label on the back of the Keypad to ensure that the batteries are installed correctly. On the Second Keypad, press the [#] Key; this message will be displayed.
Chapter 3: Adding Components 3 F: Reviewing the List of Enrolled Components In the Installer’s Programming Mode, you can display a list of all the components enrolled on the system. This function will display all of the detection devices and the zones they are assigned to, as well as the number of Sounders and Keypads enrolled on the system. Entering the Enrollment Mode (See Section 3B to Enter the Enrollment Mode) -YES Key when this message Press the is displayed.
3 G: Removing Components from the System Follow the procedure below to remove components from the system. You may wish to remove components for the following reasons: • The component is no longer required on the system • A mistake was made in enrolling the component • The component is not working and requires service ADDING COMPONENTS Enter the Enrollment Mode as described in 3 B: Entering the Enrollment Mode When this message is displayed, press the -YES Key. Use the -NO Key to scroll to this message.
Chapter 4: Module Placement and Testing Chapter Four: Module Placement and Testing explains how to: • Locate and test system components • How to enter the Placement Test Mode Do not permanently mount any of the components until they have been tested! 4 A: Locating the Controller and Sounders The components of the WLS900 System may be located almost anywhere on the premises.
4 C: Entering the Placement Test Mode Test the placement of the First Sounder before testing other components! Carry the Keypad to the location of the component to be tested. The location of the Keypad will not affect the test, as the Placement Test Mode tests the component’s ability to communicate with the Controller and Sounder, not the Keypad. Enter the Installer’s Programming Mode as described in 5 A: How to Enter the Installer’s Programming Mode.
Chapter 4: Module Placement and Testing Press the -YES Key to end the test; this message will be displayed. To continue testing, -YES Key. To enter the Installer’s press the -NO Key. Programming Mode, press the * The "ZONE LABEL" can be any discription of up to 16 letters, numbers, spaces or ASCII characters. See Section 6 for more information. During the Placement Test, the Sounders will sound and one of the messages shown here will Location Good be displayed.
Chapter 5: Installer Programming Chapter 5: Installer Programming Chapter Five: Installer Programming explains how to: • Enter the Installer’s Programming Mode • Enter data in the programming sections • How to edit the Zone Labels 5 A: How to Enter the Installer’s Programming Mode Press the [#] Key; this message will be displayed. ∗ PLACEMENT AND TESTING Enter [ ][8]; this message will be displayed. Enter the Installer’s Code. The default Installer’s Code is [0900].
Chapter 5: Installer Programming 5 B: Programming Data Entry Sections For sections that require a number value to be entered, a message similar to the one shown here will be displayed. Section Number indicates which Section is being programmed. Present Data displays the data presently programmed. Range indicates the range of valid entries. Program Item indicates the current program item. A cursor will appear under the first digit; enter the new data or -NO Key.
5 C: Programming System Option Sections System Options Programming Sections are used to enable or disable various system functions. When a System Options Section is entered, a message similar to the one shown here will be displayed. Section Number indicates which Section is being programmed. Selected Options indicate which options have been enabled or disabled by displaying the numbers 1 through 8.
Chapter 6: Zone Labels Chapter 6: Zone Labels 6 A: Editing Zone Labels Zone Labels may only be edited by entering the "Installer’s Programming" Mode, see Section 5A, and then accessing the "System Functions". Zone Labels are messages assigned to each Zone displayed on the Keypad. Zone Labels may be programmed to suit the user’s needs and to make the information the system provides more useful. For example, the label “Zone 1” could be changed to read “Front Door”.
Chapter 6: Zone Labels The letters of the alphabet have been assigned to the Number Keys on the Keypad in groups of three. To enter a letter, press a Number Key once to enter the first letter, twice to enter the second letter, three times to enter the third letter, and finally four times to enter the number itself. For example, to enter the letter “F”, press the [2] Key three times.
Chapter 7: Mounting the Components Chapter 7: Mounting the Components With the System disarmed, mount the components in their desired locations. Note that when each enrolled component is removed from its backplate, the Sounder will beep to indicate that the component’s tamper switch has been activated. 7 A: Controller Select a dry location close to an unswitched AC source and a telephone connection. Locate the Controller backplate on the wall and mark all desired screw locations; refer to Figure 1.
Chapter 7: Mounting the Components 7 C: Keypad Convenience and accessibility are the main concerns for Keypad location. The Keypad should be located as near as possible to the main entry-exit door. Mount the Keypad at a height that makes it easily accessible for all intended users. To help prevent false emergency key alarms, the Keypad should also be mounted so that it is out of reach of children. Locate the Keypad backplate on the wall and mark all desired screw locations; refer to Figure 1.
Chapter 8: System Programming Sections Chapter 8: System Programming Sections [00] Binary Programming Section [00] is only to be used on instruction from DSC Technical Personnel for specialized programming. [01] Zone Definitions Program ten 2-digit zone definitions in this section. The first digit determines the zone’s audible characteristics, while the second digit determines how the zone will operate.
Chapter 8: System Programming Sections 1 Delay 2 The Delay 2 zone operates in the same manner as the Delay 1 zone but with a different Entry Delay. The Delay 2 Entry Delay is programmed in Section [02]. 2 Instant This zone type will generate an instant alarm if the zone is opened while the system is armed. 3 Interior This zone type will only have an Entry Delay if a Delay zone is opened before the Interior zone is activated.
Chapter 8: System Programming Sections 9 Fire Fire Zones are 24-hour zones used specifically for fire detection devices. Smoke Detectors must be programmed as Fire Zones. Do not use any other Zone Definition for Smoke Detectors. On alarm, the Sounders will sound a loud beep; the beep may be programmed as either pulsed or steady. Alarm signals will be reported as they occur unless a Fire Transmission Delay is programmed.
Chapter 8: System Programming Sections [05] First System Options 1 Quick-Exit Enable / Disable ON: Quick-Exit Disabled. • OFF: Quick-Exit Enabled. With the system armed in the Home or Away Mode, enter an Access -NO Key to scroll through the Keypad messages until the “QuickCode and use the Exit” prompt is displayed; when displayed, press the -YES Key to use the Quick-Exit feature. The user will be allowed two minutes to leave the premises through a Delay Zone.
Chapter 8: System Programming Sections 3 Door Chime Option Available / Not Available ON: Door Chime Option is not available. The Master Code will not be able to turn the Door Chime feature on or off; the feature will always be off. • OFF: Door Chime Option Available. The Master Code is able to turn the Door Chime feature on or off. When Door Chime is turned on, the Sounders will sound a beep when Delay 1, Delay 2 and Instant Zones are activated.
Chapter 8: System Programming Sections [06] Second System Options 1 [F] Key Disable / Enable ON: [F] Key Disabled. The [F] Key is disabled and will not function when pressed. • OFF: [F] Key Enabled. When pressed and held for 2 seconds, a Fire Alarm will be generated. An [F] Key alarm reporting code, if programmed, will be transmitted to the monitoring station and the Sounders will sound. 2 [P] Key Disable / Enable ON: [P] Key Disabled. The [P] Key is disabled and will not function when pressed.
Chapter 8: System Programming Sections [07] Third System Options 1 Entry Delay Off Arming Option ON: “No Entry Delay” Option Available. When arming the system in the Home Mode, the user will be able to select whether or not Delay Zones will have an entry delay when opened. • OFF: “No Entry Delay” Option Not Available. Delay Zones will always have an entry delay. 2 Silent Supervisory Fault ON: Supervisory Faults are Troubles Only.
Chapter 9: Communications Programming Sections Chapter 9: Communications Programming Sections [20] First Monitoring Station Telephone Number This is the first telephone number which the communicator will dial. Enter the telephone number the way it would be dialed on a telephone, and press [#] after the last digit to complete entry of the number. Up to 15 digits and special characters may be entered in the telephone number. The following special characters may be inserted in the telephone number: For...
Chapter 9: Communications Programming Sections [23] Alarm Reporting Codes, Zones 1 to 10 Program ten 2-digit alarm reporting codes for Zones 1 through 10. Note that the use of different communications formats may determine how the Account and reporting codes are to be programmed. The examples below illustrate how different communication formats require different Account numbers and reporting codes. 3/1 Format, Single Line or Non-Extended Reporting Requires: • 3-digit Account Code in Section [22].
Chapter 9: Communications Programming Sections [29] Low Battery Reporting Codes, Zones 1 to 10 Program ten 2-digit Low Battery Reporting Codes in this section; refer to Programming Section [23] for programming instructions. These codes will be transmitted to report low battery conditions for the devices assigned to zones 1 through 10.
Chapter 9: Communications Programming Sections [34] System Trouble Reporting Codes Program eight 2-digit Maintenance Reporting Codes in this section; refer to Programming Section [23] for programming instructions.
Chapter 9: Communications Programming Sections [37] Keypad and Sounder Restoral Reporting Codes Program eight 2-digit Maintenance Restoral Reporting Codes in this section; refer to Programming Section [23] for programming instructions.
Chapter 9: Communications Programming Sections [39] Communication Variables Program six 3-digit codes in this section. Valid entries for all except the Swinger Shutdown Counter are from 000 to 255; do not enter hexadecimal numbers. The following communicator functions are programmed in this section: Swinger Shutdown Counter (number of transmissions) The Swinger Shutdown feature does not apply to Fire Zones; Fire Zone transmissions will never be shut down.
Chapter 9: Communications Programming Sections [40] Test Transmission Time of Day This section determines when the Periodic Test Transmission will be made, or when the Downloading computer will be called if Periodic Downloading is enabled.. Enter a 4-digit timeof-day in the 24-hour clock format; enter 00 to 23 for the hour, and 00 to 59 for minutes. To disable the test transmission, program ‘00’ or ‘FF’ as the Periodic Test Transmission Reporting Code in Section [38].
Chapter 9: Communications Programming Sections [42] First Communicator Options 1 Communicator Disable / Enable ON: Communicator Disabled. The system will not communicate alarms or other events. • OFF: Communicator Enabled. The system will communicate all events with programmed reporting codes. 2 Dialing Format ON: Pulse Dialing. The communicator will dial using the pulse (rotary) format. • OFF: DTMF Dialing.
Chapter 9: Communications Programming Sections [43] Second Communicator Option Code Only one of the restoral options described below may be selected. 24-hour Zones and Fire Zones will only transmit their restoral codes when their detection devices are mechanically restored 1 Restoral Follow Zone Restorals Follow Zone. While the system is armed, the zone restoral code will be transmitted immediately when the zone is restored.
Chapter 10: Downloading Programming Sections Chapter 10: Downloading Programming Sections [70] Downloading Options 1 Ring Detect ON: Ring Detect Enabled. The system will answer incoming calls from the downloading computer after the number of rings programmed in Section [74]. • OFF: Ring Detect Disabled. The system will not answer incoming calls. Downloading must be performed with the User-Initiated, Installer-Initiated or Periodic Downloading functions.
Chapter 10: Downloading Programming Sections [71] Downloading Computer Telephone Number Program the downloading computer’s telephone number in this section; refer to Programming Section [20] for programming instructions. [72] Downloading Access Code Program a 4-digit code in this section. This code is used to confirm that a valid downloading computer is accessing the system. If the Access Code programmed in the downloading computer does not match the system, the system will hang up.
Chapter 11: Installer Test Modes Chapter 11: Installer Test Modes [80] Installer Walk Test Mode Upon entering this section, the message shown here will be displayed. During the Walk Test, the Sounder will sound a loud series of beeps as each zone is opened. Note that Motion Detectors may not sound an alarm as they may have entered their High Traffic Shutdown Mode. Refer to Chapter 4D: Module Placement and Testing for instructions on testing Motion Detectors.
Chapter 12: Miscellaneous Programming Sections Chapter 12: Miscellaneous Programming Sections [90] Installer Lockout Enable Upon entering this section, the message shown here will be -YES Key to enable the Installer Lockout, displayed. Press the or press the -NO Key to exit. Once enabled, the Installer’s Code and the Downloading Access Code are protected from being reset by either the software or hardware reset functions.
Appendix A Guidelines for Locating Smoke Detectors Appendix A Guidelines for Locating Smoke Detectors Experience has shown that all hostile fires in family living units generate smoke to a greater or lesser extent. Experiments using typical fires in family living units indicate that detectable quantities of smoke precede detectable levels of heat in most cases.
Appendix B Connecting the Controller to the Telephone Line Appendix B Connecting the Controller to the Telephone Line Telephone Connections The second method uses the larger CA31A / RJ38A jack, and is better suited to installations where there is direct access to the telephone line wiring.
Appendix C ASCII Character Chart Appendix C ASCII Character Chart Use this chart when entering ASCII characters in the Zone Label Editing Mode.
LIMITED WARRANTY Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.
© 1997 Digital Security Controls Ltd. 1645 Flint Road, Downsview, Ontario, Canada M3J 2J6 Tel. (416) 665-8460 • Fax (416) 665-7498 • Tech.
• W A R N I N G • This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. Wireless Security System NOTE: Four extra AA batteries are included with each keypad. For more information, see section 3A “Enrolling the First Keypad”, on page 7. INSTALLATION MANUAL Controller Software Version 2.
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. Industry Canada does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
TABLE OF CONTENTS INTRODUCTION 1 CHAPTER 1: OVERVIEW 2 1 A: Glossary ............................................................. 2 1 B: Components ...................................................... 3 CHAPTER 2: GETTING STARTED 5 2 A: Preparing for Installation ................................... 5 2 B: Installing the Controller Battery ......................... 6 CHAPTER 3: ADDING COMPONENTS 7 3 A: Enrolling the First Keypad ................................. 7 3 B: Entering the Enrollment Mode .....
[43] Second Communicator Option Code .............. 39 1 Restoral Follow Zone ..................................... 39 2 Restorals on Sounder Time-out ..................... 39 3 Restorals on Disarming ................................. 39 4-8 For Future Use ............................................... 39 CHAPTER 10: DOWNLOADING PROGRAMMING SECTIONS 40 [70] Downloading Options ...................................... 40 1 Ring Detect ....................................................