WARNING This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. Installation Manual PC585 software version 3.
Limited Warranty WARNING Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.
Ta ble of Contents Section 1: System Introduction 1 1.1 Specifications ........................................................................1 1.2 Additional Devices ..............................................................2 1.3 Out of the Box .......................................................................2 Section 2: Getting Started 3 2.1 Installation Steps ..................................................................3 2.2 Terminal Descriptions ..........................................
P C 5 8 5 Wir i n g D i a g r a m ii
Section 1: System Introduction 1.1 Specifications Downloading Software Support • PC585 v3.
1.2 Additional Devices In addition to the information below, see the back cover for a DSC module compatibility table. PC5132 Wireless Receiver The PC5132 Wireless Receiver can be used to connect up to 32 wireless devices to the system. All devices are spread spectrum, 433 MHz, fully supervised devices (please refer to the PC5132-433 Installation Manual for more information).
Section 2: Getting Started The following sections provide a thorough description of how to wire and configure devices and zones. 2.1 Installation Steps Read this section completely before you begin. Once you have an overall understanding of the installation process, carefully work through each step. Step 1: Create a Layout Draw a rough sketch of the building to get an idea of where all alarm detection devices, keypads and other modules are to be located.
Programmable Output Terminals – PGM1 and PGM2 PGM1 can sink up to 50mA or 300mA (depending on the PGM build option) of current. Connect the positive side of the LED or buzzer to AUX+, the negative side to PGM1. If more than 50mA or 300mA of current are required, a relay must be used. PGM2 operates similarly to PGM1. However, both PGM1 and PGM2 can not sink up to 300mA of current.
G e t t i n g S t a r t e d : 2 . 5 K e y p a d A s si gn m e n t 2.5 Keypad Assignment 2.8 Zone Wiring There are eight available slots for keypads. LED keypads and the LCD5501Z keypad by default are always assigned to slot 1. LCD5500Z keypads are always assigned to slot 8. You will need to assign each keypad to its own slot (1 to 8). Keypad assignment is required, as it tells the panel which slots are occupied. The panel can then generate a fault when a keypad supervisory is not present.
NOTE: This option can only be selected if Normally Closed (NC) detection devices or contacts are being used. NOTE: Only one NC contact can be connected to each zone. Wiring multiple detection devices or contacts on a single loop is not allowed. The following chart shows zone status under certain conditions: Loop Resistance Loop Status 0Ω (shorted wire, loop shorted) Fault 5600Ω (contact closed) Secure Infinite (broken wire, loop open) Tamper 11200Ω (contact open) Violated End of Line Resistors. . . . . . .
G e t t i n g S t a r t e d : 2 . 1 1 K e y p a d Z o ne s Assigning Keypad Zones When using keypad zone inputs, each input used must be assigned a zone number in Installer’s Programming. First, ensure that you have enrolled all installed keypads into the desired slots. (see 2.5 “Keypad Assignment” ) Next, enter programming section [020] to assign the zones. There are eight programming locations in this section, one for each keypad slot. Enter a 2-digit zone number for each of the keypad zones.
Section 3: Keypad Commands Use any system keypad to enter commands and/or program the PC585 security system. The LED keypad uses function and zone indicator lights to represent alarm functions and status. If you have a PC1555RKZ keypad, the System light acts as a Trouble, Memory, Program and Bypass indicator. Unlike other LED keypads, these conditions will only be represented by the System light.
K e y p a d C o m m a n d s : 3. 4 [ *] C om m a n ds [*][2] Trouble Display The panel constantly monitors itself for several different trouble conditions. If a trouble condition is present, the Trouble (or System) light will be on and the keypad will beep twice every 10 seconds. The trouble beep can be silenced by pressing any key on any keypad. If Bell Squawk on Trouble is enabled (section [014], option [5]), the bell will squawk every 10 seconds when a trouble condition is present.
[*][5] Programming Access Codes There are 37 access codes available to the user. They are: Access code (40) ..................... One master code Access codes (01)-(32)............ 32 general access codes Access codes (33)-(34)............ Two duress codes Access codes (41)-(42)............ Two supervisor codes All access codes have the ability to arm or disarm the system and can activate the PGM Outputs using the [*][7] commands. Access codes can be either four or six digits (see 5.
K e y p a d C o m m a n d s : 3 . 5 F u nc t io n K e y s [*][7] Command Output Functions The user can activate programmable output functions using the [*][7][1-2] commands. The outputs may be activated when the system is either armed or disarmed. section [015], option [4]) to have this key function without the need to enter an access code. If Quick Arm is not enabled, the user will have to enter an access code before the system will stay arm.
3.6 Features Available for the LCD5500Z These features are only available for LCD5500Z keypads with zone inputs: Automatic Scrolling of Alarms in Memory The LCD5500Z keypad allows automatic scrolling through alarms in memory while the keypad is idle. This feature, if enabled, will override the clock display. This option can be programmed in LCD programming section [66], option [4].
Section 4: How to Program The following section of the manual describes the Installer’s Programming function and how to program the various sections. NOTE: Read the following section of the manual very carefully before you begin programming. We also recommend filling out the Programming Worksheets section before you program the panel. 4.2 Programming Decimal Data For your reference, the corresponding programming sections for the functions listed are highlighted in text boxes such as this one.
4.4 Programming Toggle Option Sections Some programming sections contain several toggle options. The panel will use zone lights 1 through 8 to indicate if the different options are enabled or disabled. Press the number corresponding to the option to turn it ON or OFF. Once all the toggle options have been selected correctly, press the [#] key to exit the section and save the changes. The Ready light will turn OFF and the Armed light will turn ON.
Section 5: Program Descriptions The following section explains the operation of all programmable features and options and provides a summary of all corresponding programming locations. [02] Delay 2 Zone The Delay 2 entry delay time can be set independently of Delay 1 in programming section [005] (System Times). 5.1 Programming Security Codes [03] Instant Zone This zone type will cause an instant alarm if it is violated when the panel is armed.
A violated Fire zone will be displayed on all keypads and can be delayed at any keypad. Typically this zone is used for latching smoke detectors. [08] Standard 24-hr Fire Zone NOTE: Do not wire Fire zones on keypad zone terminals if the DEOL supervision option is enabled for the panel (section [013], option [2]). When this zone is violated, the panel will immediately latch the alarm output and communicate to the central station.
P r o g r a m D e s c r i p t i o n s : NOTE: Any zone with the wireless attribute enabled will not cause an alarm for a fault condition when armed (or any time for 24-hr zones). Zone Attributes . . . . . . . . . . . . Sections [101] - [108]: [1] - [8] 5.4 Assigning Keypad Zones ‘Z”’keypads have zone inputs to which devices—such as door contacts—can be connected. (See 2.11 “Keypad Zones” for wiring information.
NOTE: To use the Third Telephone Number, you must enable it in section [380], option [5], and program it in section [303]. NOTE: Telephone numbers can be up to 32 digits. This allows you to add special digits if required. To program the telephone number, enter the numbers 0 through 9 as required.
P r o g r a m D e s c r i p t i o n s : reporting code to the central station, if programmed. If there is a closing or zone activity present on the system at any time, the counter will be reset. NOTE: Activity Delinquency will not be reported while the panel is armed in Away mode. NOTE: Activity on manually bypassed zones will not reset the timer. NOTE: This timer is reset when the panel is armed, or if Installer Programming is entered.
1. If an event’s reporting code is programmed as [00] or [FF], the panel will not attempt to call central station. 2. If the reporting code for an event is programmed as anything from [01] to [FE], the panel will send the programmed reporting code. Please refer to Appendix A: “Reporting Codes”for a list of SIA identifiers. SIA Sends Automatic Reporting Codes . . . Section [381]: [3] Pager Format The Communicator Format option for either telephone number can be programmed as Pager format.
P r o g r a m using the LINKS1000 with call back, you need to program the LINKS1000 Preamble with the downloading telephone number in order for the panel to call the computer correctly. NOTE: When uploading labels from LCD keypads, only labels from the LCD keypad assigned to slot 8 will be uploaded. Answering Machine/Double Call . . . . . . . . Section [401]: [1] User Enable DLS Window . . . . . . . . . . . . . Section [401]: [2] Call-Back . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE: If attribute [8] is turned ON, attributes [1-7] must also be turned ON. PGM Output Timer. . . . . . . . . . . . . . . . . . . . . . . Section [164] [11] System Tamper (All Sources) The PGM output will activate when any tamper condition is present and will deactivate when all tampers are restored. [12] TLM and Alarm The PGM output activates when the system experiences both a telephone line trouble and an alarm.
P r o g r a m TLM Enable/Disable . . . . . . . . . . . . . . . . . . Section [015]: [7] TLM Trouble Beeps When Armed or TLM Audible (Bell) When Armed . . . . . . . . Section [015]: [8] TLM Trouble Reporting Code . . . . . . . . . . . . . . Section [349] TLM Restoral Reporting Code . . . . . . . . . . . . . Section [350] TLM Trouble Delay . . . . . . . . . . . . . . . . . . . . . . Section [370] 5.13 Bell The bell will silence after the number of minutes programmed for the Bell Cut-off time have passed.
squawk the bell only when the system is away armed or disarmed. The Opening After Alarm Keypad Ringback option will cause the keypad to beep 8 times rapidly after the Opening After Alarm reporting code has been successfully transmitted to the central station. The Opening After Alarm Bell Ringback option will cause the panel to squawk the bell 8 times rapidly after the Opening After Alarm reporting code has been successfully transmitted to the central station.
P r o g r a m D e s c r i p t i o n s : 5 . 2 0 E v e n t B uf f e r 5.20 Event Buffer 5.24 Loop Response The panel will store the last 128 events which occurred on the system. The Event Buffer will contain the name, time and date of each event, along with the zone number, access code number or any other information pertaining to the event. If the Event Buffer Follows Swinger Shutdown option is enabled, the event buffer will not store events after the Swinger Shutdown level has been reached.
When used as a backup communicator, the panel will attempt to call the central station in the following manner: the panel will try to call using land lines – if unsuccessful, the panel will try to call using the LINKS – if unsuccessful, the panel will try to call using the land lines on the next dialing attempt. This process will continue until the panel has successfully communicated with the central station or until the panel’s programmed number of dialing attempts have been exhausted.
Restore PC5132 to Default Programming . . . . Section [996] Restore PC5400 Printer to Default ProgrammingSection [997] Restore Panel to Default Programming . . . . . . Section [999] 5.31 Installer’s Lockout If Installer’s Lockout is selected, a hardware default cannot be performed. If a software default is performed, all programming will restore to factory default.
S e ct i on 6 : Prog rammi ng Works he e ts For the Record Customer: _______________________________________________________________________________________________________ Address: ________________________________________________________________________________________________________ Telephone: ___________________________________________ Installation Date: ___________________________________________ Installer’s Code: _________________________________________________________________________________________
P r o g r a m m i n g W o r k s h e e t s Zone Programming Summary Zone programming can be found in sections [001] - [004], [101] - [132], [020] and [202] - [205]. Use this area to record a summary of your zone programming. Refer to Appendix B: “Programming Keypads”, for instructions on programming zone labels.
Keypad Programming [000] Keypad Enrollment (Section 2.5 “Keypad Assignment”) NOTE: This must be done at each keypad requiring programming. [0] Slot [Valid entries are 11-18; i.e. enter [11] for slot 1, [12] for slot 2, etc.
P r o g r a m m i n g W o r k s h e e t s NOTE: Zones 9-32 are only available for wireless zones. [002] Zone 9-16 Definitions (Section 5.2 “Zone Programming”) Default Default 00 I_______I_______I Zone 9 00 I_______I_______I Zone 13 00 I_______I_______I Zone 10 00 I_______I_______I Zone 14 00 I_______I_______I Zone 11 00 I_______I_______I Zone 15 00 I_______I_______I Zone 12 00 I_______I_______I Zone 16 [003] Zone 17-24 Definitions (Section 5.
[012] Keypad Lockout Options (Section 5.21 “Keypad Lockout Options”) NOTE: If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch. Default I_______I_______I_______I Number of Invalid Codes Before Lockout (001-255 codes) 000 000 I_______I_______I_______I Lockout Duration (001-255 minutes) [013] First System Option Code Default Option ON 1 Normally Closed Loops OFF I________I Off End-of-Line Resistors Section 2.
P r o g r a m m i n g [017] Fifth System Option Code Default Option ON 1 WLS Key Does Not Use Access Codes* ON I________I Off WLS Key Uses Access Codes OFF I________I 2-5 OFF I________I 6 Daylight Savings Time Enabled OFF I________I 7 For Future Use OFF I________I 8 Squawk on Away Arming/Disarming OnlyBell Squawk on all Arming/Disarming W o r k s h e e t s Section 5.17 For future use Daylight Savings Time Disabled 5.33 5.17 *This option must be enabled when using a PC5132 v2.
Advanced System Programming Zone Attributes (Section 5.3 “Zone Attributes”) Zone Attribute Defaults (Y = Option ON; N = Option OFF): Attribute: ON OFF Zone Type: 00 Null Zone 01 Delay 1 02 Delay 2 03 Instant 04 Interior 05 Int. Stay/Away 06 Dly. Stay/Away 07 Dly. 24hr Fire (Hardw.) 08 Stand. 24hr Fire (Hardw.) 09 24hr Superv. 10 24hr Superv.
P r o g r a m m i n g W o r k s h e e t s [117] 17 ( ) I________I I________| I________| I________| I________| I________| I________| I________I [118] 18 ( ) I________I I________| I________| I________| I________| I________| I________| I________I [119] 19 ( ) I________I I________| I________| I________| I________| I________| I________| I________I [120] 20 ( ) I________I I________| I________| I________| I________| I________| I________| I________I [121] 21 ( )
[160] Maximum Dialing Attempts to Each Telephone Number (Section 5.5 “Communicator – Dialing”) Default: 008 I_______I_______I_______I Valid entries are 001-015 attempts (do not enter 000). [161] Post Dial Wait for Handshake (All Formats) (Section 5.5 “Communicator – Dialing”) Default: 040 I_______I_______I_______I Valid entries are 001-255 seconds [164] PGM Output Timer (Section 5.
P r o g r a m m i n g W o r k s h e e t s Alarm Restoral Reporting Codes, Zones 1-32 (Section 5.
Closing (Arming) Reporting Codes, Access Codes 1-32 (Section 5.
P r o g r a m m i n g W o r k s h e e t s [352] Test Transmission Reporting Codes (Section 5.8 “Communicator – Reporting Codes” & Appendix A) I_______I_______I 1. Periodic Test Transmission I_______I_______I 3. LINKS1000 Test Transmission Code* 2. System Test *The LINKS Test Transmission Code must be programmed as “00” for the LINKS Test Transmission to be disabled. I_______I_______I [353] Wireless Maintenance Reporting Codes (Section 5.
[370] Communication Variables Default I_______I_______I_______I Swinger Shutdown (Alarms and Rest) (001-014 Transmissions, 000=disabled) 003 Section 5.19 003 I_______I_______I_______I Swinger Shutdown (Tampers and Rest)(001-014 Transmissions, 000=disabled) 003 I_______I_______I_______I Swinger Shutdown (Maint and Rest) (001-014 Transmissions, 000=disabled) 5.19 000 I_______I_______I_______I Transmission Delay (001-255 seconds) 5.
P r o g r a m m i n g W o r k s h e e t s Downloading Options [401] First Downloading Option Code (Section 5.
Module Programming [801] PC5400 Printer Module Programming Please refer to your PC5400 Installation Manual for installation and programming instructions. [803] Alternative Communicator Programming Please refer to your LINKS2X50 Installation Manual for installation and programming instructions. [804] PC5132 Wireless Expansion Programming Please refer to your PC5132 Installation Manual for programming locations and instructions.
Appendix A: Reporting Codes The following tables contain Contact ID and Automatic SIA format reporting codes. For more information on reporting code formats and notes about individual reporting codes, see sections 5.8 “Communicator – Reporting Codes” and 5.9 “Communicator – Reporting Formats”. Contact ID The first digit (in parentheses) will automatically be sent by the control. The second two digits are programmed to indicate specific information about the signal.
Section # [350] [349-350] [351] [351] [351] [351] [351] [351] [352] [352] [352] [353] Reporting Code Code Sent When... TLM Restore Gen System Supervisory Trouble/Rest.
Appendix B: Programming Keypads If you have an LCD5500Z keypad, additional programming is required for proper operation. All LCD programming is done per keypad. If more than one LCD keypad are present on the system, labels programmed at one keypad can be broadcast to all other LCD keypads. Check the software version of the keypad you are programming, and refer to the correct programming instructions. LCD5500Z v2.
[60] First User Display Mask Default Option ON I_______I 1 Hold [P]anic Keys prompt ON ON OFF Hold [P]anic Keys prompt OFF ON I_______I 2 Zone Bypassing prompt ON Zone Bypass prompt OFF ON I_______I 3 Troubles prompt ON Troubles prompt OFF ON I_______I 4 Alarm Memory prompt ON Alarm Memory prompt OFF ON I_______I 5 Door Chime Control prompt ON Door Chime Control prompt OFF ON I_______I 6 Access Codes prompt ON Access Codes prompt OFF ON I_______I 7 User Functions prompt ON Use
[66] Keypad Options Default Option I_______I 1 ON ON Display Access Code when Programming OFF Display ‘X’ when Programming ON I_______I 2 Local Clock Display Enabled Local Clock Display Disabled OFF I_______I 3 Local Clock Displays 24-hr time Local Clock Displays AM/PM ON I_______I 4 Auto Alarm Memory Scroll Enabled Auto Alarm Memory Scroll Disabled OFF I_______I 5 Local Display of Temperature Enabled* Local Display of Temperature Disabled OFF I_______I 6 Bypass Options prompt ON
Refer to the following chart: Programmable Labels Zone labels and other LCD display identifiers can be customized to [1] - A, B, C, 1 [6] - P, Q, R, 6 make operation of the system easier for the end user. The following [2] - D, E, F, 2 [7] - S, T, U, 7 procedure should be used for creating all LCD labels: [3] - G, H, I, 3 [8] - V, W, X, 8 [4] - J, K, L, 4 [9] - Y, Z, 9,0 1. Enter Installer’s Programming. Enter the three-digit section num[5] - M, N, O, 5 [0] - Space ber for the label to be programmed. 4.
P r o g r a m m i n g [075] Fourth User Display Mask Default Option ON I_______I 1 User Initiated Call-up prompt ON ON W o r k s h e e t s : 5 .
Command Output Labels Default: “Command_O/P_1” - “Command_O/P_4” Program a label for each Command Output used, as it will appear at each partition.
P r o g r a m m i n g W o r k s h e e t s : 5 . 3 3 Daylight Savings Time [997] View Software Version [998] Initiate Global Label Broadcast All LCD programming is done per keypad. If more than one LCD keypad are present on the system, and the PC5400 receives labels, labels programmed at one keypad can be broadcast to all other LCD keypads. Perform the following procedure in order to broadcast labels: Step 1 - Program one LCD keypad completely.
PC585 Module Compatibility Module Classic Escort (VPM-1) DLM-1 DLM-4 v1.x DLM-4 v1.0L DLM-7 Escort5580(TC) LCD5500 v1.X LCD5500Z v2.X LCD5501Z LCD5501Z32-433 PC5502Z2 LCD600 LED615 Links1000 Links2150 Links2450 PC-16 Out PC1500RK PC1555RKZ PC5102 PC5108 PC5108L PC5132 v1.X PC5132 v2.X PC5132 v3.X PC5200 PC5204 PC5208 PC5320 PC5400 Printer Module v2.2 PC5400 Printer Module v1.X to v2.1 PC5400 Printer Module v2.
