PK5590CL Touch Screen Security Interface Compatible with PowerSeries Control Panels User Guide IMPORTANT This manual contains information on the limitations regarding product use and function and information on the limitations as to liability of the manufacturer. Read the entire manual carefully.
INDEX ..............................Page QUICK REFERENCE Access Codes .....................13 Arming ....... Away .............................8 ....... Stay...............................7 Brightness...........................11 Bypassing Zones ..................9 Chime....................................9 Clean Mode.........................11 Contrast ..............................11 Disarming...........................7,8 Emergency Buttons...............2 Functions ............................
1. Introduction The PK5590CL Touch Screen is an interactive touch-sensitive color LCD that can be used on Partition 1 of any PowerSeries control panel. Due to the custom requirements of individual installations some of the features described here may perform differently than described. Refer to your installer’s instructions for the details of your specific installation and to the User manual for general security system information. Specifications/Features Display............................................
Controls & Indicators The following table lists the Led Indicator and push button functions. Most operations are performed by tapping an area indicated on the screen displayed. Function Description LED Indicators: Ready Light (GREEN) ON indicates the system is ready for arming. The system cannot be armed unless the Ready light is ON. Armed Light (RED) ON indicates the system has been successfully Stay Armed or Away Armed. FLASHING indicates the system has been successfully armed with no entry delay.
Figure 1, Controls & Indicators Context Sensitive Help Title Bar Work Area Status Bar LED Status Indicators Date Fire Auxiliary Panic EMERGENCY BUTTONS 3 Time
LCD Touch Screen Welcome screen The Touch Screen LCD is 1/4 VGA 320 x 240 pixel display This screen will blank after 15 minutes of inactivity. Tapping the screen will restore the display. During normal operation (unarmed) and system startup the WELCOME screen is displayed. From here a series of screens can be accessed that allow the user to perform Arming/disarming and other User functions.
Figure 2, Touch Screen Flowchart Welcome Screen Main Menu Screen Stay Arm Screen Away Arm Screen Bypass Screen Settings (1) Screen Numeric Keypad Logs Screen Functions Screen Numeric Keypad Numeric Keypad Arming Screen Disarm Screen Numeric Keypad Settings (2) Screen Clean Mode Screen Time/Date Screen User Codes Screen Numeric Keypad 5 Settings Chime English/French Settings Silence Beeps Brightness Contrast Save (Brightness/Contrast)
Main Menu screen The Main Menu screen allows you to select the following functions. To select a function tap on the associated virtual push button. Note: If PowerSave has been enabled, the screen will blank after 1 minute. Tap the screen once to display the Welcome screen. Tap the screen again to display the Main Menu screen.
Stay Armed When Stay Arm is Selected: NOTE: If Quick arm is not enabled by the installer, then a numerical keypad will be displayed. Enter a valid access code, then tap “Enter” to proceed. • “System is Arming" will be displayed in the work area • The Armed LED Indicator turns ON • “Exit Delay-Bypass” is displayed in the Status Bar.
Away Arm When Away Arm is Selected: NOTE: If Quick Arm is not enabled by the installer, then a numerical keypad will be displayed. Enter a valid access code, then tap “Enter” to proceed. • • • • “System is Arming" will be displayed in the work area The Armed LED Indicator turns ON “Exit Delay” is displayed in the Status Bar. The pre-programmed Exit Delay begins The Touchscreen “chirps” at a 1-second urgency interval during the Exit Delay. Then will sound 3 chirps in the last 10 seconds.
Bypass The Bypass screen displays the Zone Number and Status NOTE: If an Access Code is required to bypass zones • • • A numeric keypad is displayed Enter (tap) your Access Code then tap the Enter button The system returns to the updated Zone screen UP: scrolls cursor up through the displayed zones DOWN: scrolls cursor down through the displayed zones CHANGE: toggles highlighted zone to/from bypassed condition DONE: enables changes and returns to the WELCOME screen Logs screen Displays Date, Time and a
Function screen Allows the user to select any of four predefined functions NOTE: These functions must be configured by your Installer to Take effect.
Clean Mode The Clean Mode allows the user to touch (i.e., clean) the screen without enabling or disabling any functions. The screen will remain in this mode for 10 seconds, then return to the 1st Configuration Menu screen More > > Allows the User to: Adjust Display Contrast • Tapping > icon increases contrast. • Tapping < icon decreases contrast Configuration Screen (2) Adjust Display Brightness • Brightness: Tapping > icon increases brightness.
Time/Date This screen allows the User to Change Date and Time.
User Codes/Menu This screen allows you to Enable or Disable a User, or Delete a User Selecting Access Codes will display a numeric keypad • Enter your Master Code and tap Enter If the access code is correct, the User Menu will be displayed UP DOWN CHANGE: - allows you to scroll UP through the Users - allows you to scroll DOWN through the Users - If the cursor is positioned over a disabled Access Code • Selecting Change will display a numeric Keypad • Enter a new 4 or 6-digit code then tap ENTER • The scre
FCC Compliance Statement Limited Warranty Caution: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception.
