Installation manual

Programming Worksheets
39
[370] Communication Variables
Default Section Page #
003 I_______I_______I_______I Swinger Shutdown (Alarms and Rest) (001-014 Transmissions, 000=disabled) 5.19 24
003 I_______I_______I_______I Swinger Shutdown (Tampers and Rest)(001-014 Transmissions, 000=disabled) 5.19 24
003
I_______I_______I_______I Swinger Shutdown (Maint and Rest) (001-014 Transmissions, 000=disabled) 5.19 24
000 I_______I_______I_______I Transmission Delay (001-255 seconds) 5.15 23
030 I_______I_______I_______I AC Failure Communication Delay (001-255 minutes) 5.8 17
003
I_______I_______I_______I TLM Trouble Delay (No. of checks required - valid entries 003 - 255) 5.12 22
030 I_______I_______I_______I Test Transmission Cycle (land line) (001-255 days) 5.14 23
030 I_______I_______I_______I Test Transmission Cycle (LINKS) (001-255 days) 5.14 23
007
I_______I_______I_______I Zone Low Battery Transmission Delay (000-255 days) 5.8 17
030 I_______I_______I_______I Delinquency Transmission Cycle (000-255 days/hours) 5.8 17
NOTE: To disable the AC failure communications delay, program [000].
[371] Test Transmission Time of Day (Section 5.14 “Test Transmission” on page 23)
Default
9999 I_______I_______I_______I_______I (Valid entries are 0000-2359, 9999 to disable)
[380] First Communicator Option Code
Default Option ON OFF Section Page #
ON
I_______I 1 Communications Enabled Communications Disabled 5.5 17
OFF
I_______I 2 Restorals on Bell Time-out Restorals Follow Zones 5.8 17
OFF
I_______I 3 Pulse Dialing DTMF Dialing 5.5 17
ON
I_______I 4 Switch to Pulse Dialing on 5th Attempt DTMF Dial For All Attempts 5.5 17
OFF
I_______I 5 3rd Telephone Number enabled 3rd Telephone Number disabled 5.7 17
OFF
I_______I 6 Alternate Dial (1st and 3rd) Call 1st Number, Backup to 3rd 5.7 17
OFF
I_______I 7 Call LINKS as well as Land Line LINKS is Backup of Land Line(s) 5.26 25
OFF
I_______I 8 Delinquency Follows Zone Activity (Hours) Delinquency Follows Arming (Days) 5.8 17
[381] Second Communicator Option Code
Default Option ON OFF Section Page #
OFF
I_______I 1 Open After Alarm Kypd Ringback enabled Open After Alrm Kypd Ringback disabled 5.17 23
OFF
I_______I 2 Open After Alarm Bell Ringback enabled Open After Alrm Bell Ringback disabled 5.17 23
OFF
I_____ __I 3 SIA Sends Programmed Rep. Codes SIA Sends Automatic Rep. Codes 5.9 19
OFF I_______I 4 Closing Confirmation Enabled Closing Confirmation Disabled 5.17 23
OFF
I_______I 5-6 For future use —
ON
I_______I 7 Contact ID Uses Programmed Rep. Codes Contact ID Uses Automatic Rep. Codes 5.9 19
OFF
I_______I 8 For future use —
[390] LINKS Preamble (First Telephone Number)
(Section 5.26 “LINKS1000 Cellular Communicator” on page 25)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[391] LINKS Preamble (Second Telephone Number)
(Section 5.26 “LINKS1000 Cellular Communicator” on page 25)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[392] LINKS Preamble (Third Telephone Number)
(Section 5.26 “LINKS1000 Cellular Communicator” on page 25)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[393] LINKS Special Function Preamble (All Telephone Numbers)
(Section 5.26 “LINKS1000 Cellular Communicator” on
page 25)
Default: FFFFFF I_______I_______I_______I_______I_______I_______I (Program all unused digits with Hex F)
•Enter [*][2][*] (HEX B) to dial [*] • Enter [*][3][*] (HEX C) to dial [#]