WARNING This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. This panel will not operate if installed outside of North America. See section 1.1 for details. Installation Manual Software Version 2.3 / DLS-1 v6.7 and up See Back Cover for New Features in Version 2.
WARNING Please Read Carefully N o te t o I n s t al le r s This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. S ys te m Fa i lu r e s This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection.
Ta b le o f Co nte nts Section 1: System Introduction 1 1.1 Specifications ........................................................................1 1.2 Additional Devices ..............................................................2 1.3 Out of the Box .......................................................................2 Section 2: Getting Started 3 2.1 Installation Steps ..................................................................3 2.2 Terminal Descriptions ......................................
P C 5 8 0 Wiri ng Di ag ram ii
S e c tion 1 : Sy s te m Intro d u cti o n 1.1 Specifications Downloading Software Support • PC580 v2.3 uses DLS-1 v6.7 and up.
1.2 Additional Devices In addition to the information below, see the back cover for a DSC module compatibility table. PC5132 Wireless Receiver The PC5132 Wireless Receiver can be used to connect up to 32 wireless devices to the system. All devices are spread spectrum, 900 MHz, fully supervised devices which use standard ‘AAA’ or ‘AA’ alkaline batteries. Seven devices are available.
S ec tion 2: Ge tti ng Starte d The following sections provide a thorough description of how to wire and configure devices and zones. 2.1 Installation Steps Read this section completely before you begin. Once you have an overall understanding of the installation process, carefully work through each step. Step 1: Create a Layout Draw a rough sketch of the building to get an idea of where all alarm detection devices, keypads and other modules are to be located.
Programmable Output Terminals – PGM1 and PGM2 Each PGM output is designed so that when activated by the panel, the terminal will switch to ground PGM1 can sink up to 50mA of current. Connect the positive side of the LED or buzzer to AUX+, the negative side to PGM1. PGM2 operates similarly to PGM1. If more than 50 mA of current are required, a relay must be used. Please study PGM wiring in the accompanying diagram. For a list of the programmable output options, please see section 5.
G e t t i n g S t a r t e d : 2 . 6 S u p e r v i s i o n 5. Press [#] twice to exit installer programming. After assigning all keypads, perform a supervisory reset by entering section [902] in installer’s programming. The panel will now supervise all assigned keypads and enrolled modules on the system. NOTE:If you change the zone supervision options from DEOL to EOL or from NC to DEOL (section [013], options [1] or [2]), you should power down the system completely, and then power it back up.
NOTE:Only one NC contact can be connected to each zone. Wiring multiple detection devices or contacts on a single loop is not allowed. This type of zone always requires a single EOL resistor (5600Ω). Wire this zone according to the above diagram.
G e t t i n g S t a r t e d : 2 . 1 1 K e y p a d Z o n e s Assigning Keypad Zones When using keypad zone inputs, each input used must be assigned a zone number in Installer’s Programming. First, ensure that you have enrolled all installed keypads into the desired slots. (See 2.5 “Keypad Assignment” on page 4.) Next, enter programming section [020] to assign the zones. There are eight programming locations in this section, one for each keypad slot.
S e c tion 3 : Ke y p ad Co mmand s Use any system keypad to enter commands and/or program the PC580 security system. The LED keypad uses function and zone indicator lights to represent alarm functions and status. If you have a PC1555RKZ keypad, the System light acts as a Trouble, Memory, Program and Bypass indicator. Unlike other LED keypads, these conditions will only be represented by the System light.
K e y p a d Activate Stay/Away Zones If the system is armed in stay mode, the [*][1] command can be used to activate the stay/away zones. [*][2] Trouble Display The panel constantly monitors itself for several different trouble conditions. If a trouble condition is present, the Trouble (or System) light will be on and the keypad will beep twice every 10 seconds. The trouble beep can be silenced by pressing any key on any keypad.
[*][5] Programming Access Codes There are 37 access codes available to the user. They are: Access code (40) ..................... One master code Access codes (01)-(32)............ 32 general access codes Access codes (33)-(34)............ Two duress codes Access codes (41)-(42)............ Two supervisor codes All access codes have the ability to arm or disarm the system and can activate the PGM Outputs using the [*][7] commands.
K e y p a d press [#] to exit. This feature can be accessed on LED keypads by pressing and holding the [*] key. [*][7] Command Output Functions The user can activate programmable output functions using the [*][7][1-2] commands. The outputs may be activated when the system is either armed or disarmed. [*] [7] [1] – Command Output Option #1: Press [*] [7] [1] [Access Code, if required] to activate outputs programmed as PGM output option [19].
[*][6] User Functions: A valid master code must also be entered. [13] [*][7][1] Command Output Option #1: A valid access code may need to be entered. [14] [*][7][2] Reset (Command Output Option #2): As described above. [15] For future use [16] [*][0] Quick Exit: As described above. [17] [*][1] Reactivate Stay/Away Zones [18] - [20] For future use [12] 3.
S e c tion 4: Ho w to P ro g ram The following section of the manual describes the Installer’s Programming function and how to program the various sections. NOTE: Read the following section of the manual very carefully before you begin programming. We also recommend filling out the Programming Worksheets section before you program the panel. For your reference, the corresponding programming sections for the functions listed are highlighted in text boxes such as this one. 4.
4.4 Programming Toggle Option Sections Some programming sections contain several toggle options. The panel will use zone lights 1 through 8 to indicate if the different options are enabled or disabled. Press the number corresponding to the option to turn it ON or OFF. Once all the toggle options have been selected correctly, press the [#] key to exit the section and save the changes. The Ready light will turn OFF and the Armed light will turn ON.
S e c tion 5 : Pro gram De s cri p ti o ns The following section explains the operation of all programmable features and options and provides a summary of all corresponding programming locations. 5.1 Programming Security Codes There are three codes which can be programmed by the installer in the Installer’s Programming function: the Master code, the Installer’s code, and a Maintenance code. All other access codes can be programmed through the [*][5] command.
the Bell Cutoff time expires (Section [005] “System Times”), or until a code is entered. (See 5.13 “Bell” on page 22.) NOTE:If a second Fire type zone is violated or if the Fire keys are pressed during the delay period, the panel will latch the alarm output and will immediately communicate the alarm. A violated Fire zone will be displayed on all keypads and can be delayed at any keypad. Typically this zone is used for latching smoke detectors.
P r o g r a m D e s c r i p t i o n s : and bell for a zone once its swinger limit has been reached. (See 5.19 “Swinger Shutdown” on page 24.) • Transmission Delay Enable – This attribute determines whether or not the panel will delay communicating the alarm reporting code for the programmed Transmission Delay Period. (See 5.15 “Transmission Delay” on page 23.) • Wireless Zone – This attribute determines which zones are to have wireless devices.
Reporting codes can be one or two digits and can use HEX digits (A through F). For a complete description of reporting codes which can be programmed and lists of automatic Contact ID and SIA format codes, please see Appendix A: “Reporting Codes” on page 42. NOTE:Do not use the digit C in a reporting code when using Pager Format. In most cases, the digit C will be interpreted as a [#], which will terminate the page before it has finished.
P r o g r a m 5.9 D e s c r i p t i o n s : Communicator – Reporting Formats Each communication telephone number can be programmed to report using any one of eight formats available. Two 20 BPS pulse formats are supported, in addition to Contact ID, SIA and Pager formats. The Communicator Call Direction options can be used to disable the reporting of events such as Openings and Closings.
Hex [C] - simulates the [#] key on a touch tone telephone Hex [D] - forces the panel to search for dial tone Hex [E] - two second pause Hex [F] - marks the end of the telephone number The panel will attempt to call the pager once. Once the appropriate telephone number is dialed, the panel will send the account number and Reporting Code followed by the [#] key (Hex [C]). The panel has no way of confirming if the pager was called successfully.
P r o g r a m NOTE:Only ONE of options [03] Sensor Reset and [20] [*][7][2] Command Output Option #2 may be programmed on the same system. [04] For future use [05] Armed Status When the system is armed, the PGM output will activate at the beginning of the exit delay. The output deactivates when the system is disarmed. [06] Ready To Arm The PGM will be active as long as the system is ready to arm and all non-force armable zones on the system are restored.
[18] Stay Armed Status When the system is armed in the Stay mode, the PGM output will activate at the beginning of the exit delay. The output deactivates when the panel is disarmed. [19] [*][7][1] Command Output Option #1 [20] [*][7][2] Command Output Option #2 These outputs are user-initiated by entering [*][7][1-2] at any keypad. When any output is activated, three acknowledgment beeps are sounded.
P r o g r a m 5.14 Test Transmission To ensure that the communication link with the central station is functioning properly, program the panel to send a test transmission signal on a regular basis. The panel can send a Periodic Test Transmission Reporting Code at the programmed Test Transmission Time of Day. The Test Transmission Cycle determines the period of time between tests. NOTE:The LINKS Test Transmission can only be programmed in days.
Quick Arm Enable . . . . . . . . . . . . . . . . . . . . Section [015]: [4] Quick Exit Enable . . . . . . . . . . . . . . . . . . . . Section [015]: [3] Arm/Disarm Bell Squawk. . . . . . . . . . . . . . . Section [014]: [1] Squawk on Away Arm/Disarm Only. . . . . . . Section [017]: [8] Closing Confirmation . . . . . . . . . . . . . . . . . . Section [381]: [4] Opening After Alarm Keypad Ringback . . . Section [381]: [1] Opening After Alarm Bell Ringback . . . . . .
P r o g r a m 5.22 Keypad Blanking If the Blank Keypad When Not in Use option is enabled, the panel will turn off all lights and LCDs on the keypads when no keys are pressed for 30 seconds. The keys, however, will remain backlit. The panel will turn the lights and LCDs back on if entry delay begins or an audible alarm occurs. The lights and LCDs will also come on if a key is pressed or, if a valid access code is entered when the Code Required to Restore Blanking option is enabled.
(Downloading Telephone Number) . . . . . . . . . . Section [490] Communicator Call Direction Options. . . Section [361]-[368] Call LINKS as well as Land Line . . . . . . . . . Section [380]: [7] LINKS Special Preamble . . . . . . . . . . . . . . . . . . Section [393] 5.
S e ction 6 : Pro grammi ng Works he et s For the Record Customer: _______________________________________________________________________________________________________ Address: ________________________________________________________________________________________________________ Telephone: ___________________________________________ Installation Date: ___________________________________________ Installer’s Code: ___________________________________________________________________________________________
Zone Programming Summary Zone programming can be found in sections [001] - [004], [101] - [132], [020] and [202] - [205]. Use this area to record a summary of your zone programming. Refer to Appendix B: “Programming LCD Keypads” on page 44, for instructions on programming zone labels.
P r o g r a m m i n g W o r k s h e e t s Keypad Programming [000] Keypad Enrollment (Section 2.5 “Keypad Assignment” on page 4) NOTE: This must be done at each keypad requiring programming. [0] Slot [Valid entries are 11-18; i.e. enter [11] for slot 1, [12] for slot 2, etc.
NOTE:Zones 9-32 are only available for wireless zones. [002] Zone 9-16 Definitions (Section 5.2 “Zone Programming” on page 15) Default Default 00 I_______I_______I Zone 9 00 I_______I_______I Zone 13 00 I_______I_______I Zone 10 00 I_______I_______I Zone 14 00 I_______I_______I Zone 11 00 I_______I_______I Zone 15 00 I_______I_______I Zone 12 00 I_______I_______I Zone 16 [003] Zone 17-24 Definitions (Section 5.
P r o g r a m m i n g W o r k s h e e t s [012] Keypad Lockout Options (Section 5.21 “Keypad Lockout Options” on page 24) NOTE:If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch. Default 000 I_______I_______I_______I Number of Invalid Codes Before Lockout (001-255 codes) 000 I_______I_______I_______I Lockout Duration (001-255 minutes) [013] First System Option Code Default Option ON 1 Normally Closed Loops OFF I________I Off End-of-Line Resistors Section Page # 2.
[017] Fifth System Option Code Default Option ON 1 WLS Key Does Not Use Access Codes* ON I________I OFF I________I 2-7 OFF I________I 8 Off WLS Key Uses Access Codes Section Page # 5.17 23 For future use Squawk on Away Arming/Disarming OnlyBell Squawk on all Arming/Disarming 5.17 23 *This option must be enabled when using a PC5132 v2.1 or earlier. [020] Keypad Zone Assignments (Section 2.11 “Keypad Zones” on page 6) NOTE:Only one keypad may be assigned to a zone.
P r o g r a m m i n g W o r k s h e e t s Advanced System Programming Zone Attributes (Section 5.3 “Zone Attributes” on page 16) Zone Attribute Defaults (Y = Option ON; N = Option OFF): Attribute: ON OFF Zone Type: 00 Null Zone 01 Delay 1 02 Delay 2 03 Instant 04 Interior 05 Int. Stay/Away 06 Dly. Stay/Away 07 Dly. 24hr Fire (Hardw.) 08 Stand. 24hr Fire (Hardw.) 09 24hr Superv. 10 24hr Superv.
[116] 16 ( ) I________I I________| I________| I________| I________| I________| I________| I________I [117] 17 ( ) I________I I________| I________| I________| I________| I________| I________| I________I [118] 18 ( ) I________I I________| I________| I________| I________| I________| I________| I________I [119] 19 ( ) I________I I________| I________| I________| I________| I________| I________| I________I [120] 20 ( ) I________I I________| I________| I______
P r o g r a m m i n g W o r k s h e e t s Section PGM # [141] 1 Output Type* ( ) 1 2 3 4 5 6 7 8 I________I I________| I________| I________| I________| I________| I________| I________I [142] ( I________I I________| I________| I________| I________| I________| I________| I________I 2 ) *Record here based on programming in [009]. [160] Maximum Dialing Attempts to Each Telephone Number (Section 5.
Alarm Restoral Reporting Codes, Zones 1-32 (Section 5.8 “Communicator – Reporting Codes” on pg.
P r o g r a m m i n g W o r k s h e e t s Closing (Arming) Reporting Codes, Access Codes 1-32 (Section 5.8 “Communicator – Reporting Codes” on pg.
[353] Wireless Maintenance Reporting Codes (Section 5.8 “Communicator – Reporting Codes” on pg. 17, & Appendix A) I_______I_______I 1. Wireless Device Low Battery Alarm I_______I_______I 2. Wireless Device Low Battery Restore [360] Communicator Format Options (Section 5.9 “Communicator – Reporting Formats” on page 19) NOTE:The Third telephone number follows the format of the First telephone number.
P r o g r a m m i n g W o r k s h e e t s [370] Communication Variables Default I_______I_______I_______I Swinger Shutdown (Alarms and Rest) (001-014 Transmissions, 000=disabled) 003 Section 5.19 Page # 24 5.19 24 003 I_______I_______I_______I Swinger Shutdown (Tampers and Rest)(001-014 Transmissions, 000=disabled) 003 I_______I_______I_______I Swinger Shutdown (Maint and Rest) (001-014 Transmissions, 000=disabled) 5.
Downloading Options [401] First Downloading Option Code (Section 5.
P r o g r a m m i n g W o r k s h e e t s Module Programming [801] PC5400 Printer Module Programming Please refer to your PC5400 Installation Manual for installation and programming instructions. [803] Alternative Communicator Programming Please refer to your LINKS2X50, Skyroute, PC5400 ADT DVACS or PC5400 Sur-Gard DVACS Installation Manual for installation and programming instructions.
A p p e n d ix A: R e p o rti ng Co d e s The following tables contain Contact ID and Automatic SIA format reporting codes. For more information on reporting code formats and notes about individual reporting codes, see sections 5.8 “Communicator – Reporting Codes” on page 17 and 5.9 “Communicator – Reporting Formats” on page 19. Contact ID The first digit (in parentheses) will automatically be sent by the control. The second two digits are programmed to indicate specific information about the signal.
R e p o r t i n g Section # Reporting Code Code Sent When... [349-350] AC Line Trouble/Rest. [349-350] Main Bell Trouble/Rest. [349-350] [349-350] Fire Trouble/Rest. Auxiliary Power Trouble/ Rest. TLM Failure AC power to control panel is disconnected or interrupted/AC power restored (Both codes follow AC Failure Comm. Delay.
Appendix B: Programming LCD Keypads If you have an LCD5500Z Keypad, additional programming is required for proper operation. The following is a description of the available programming options and their accompanying programming sections: How to Enter LCD Programming Follow the programming procedure as outlined in Section 4 by pressing [*][8][Installer’s Code]. Press the [*] key. Enter the two digit Section number to be programmed.
P r o g r a m m i n g L C D K e y p a d s [61] Second User Display Mask Default Option ON OFF I_______I 1 Installer Programming prompt ON Installer Programming prompt OFF OFF I_______I 2 Stay Arm prompt ON Stay Arm prompt OFF ON ON I_______I 3 Quick Arm prompt ON Quick Arm prompt OFF I_______I 4 Interior Arm prompt ON Interior Arm prompt OFF ON I_______I 5 Quick Exit prompt ON Quick Exit prompt OFF OFF ON I_______I 6 View Event Buffer prompt ON View Event Buffer prompt OFF I_______I 7-8 For future use OF
NOTES: 46
F CC C O M P L IA N C E S TAT E M E N T CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PC580 Module Compatibility Module Compatible? Classic Escort (VPM-1) Escort5580 PC-16 Out PC5204 PC5208 PC5108 PC5108L PC5132 v1.X PC5132 v2.X PC5132 v3.X PC5506 PC55XX PC55XXZ PC5509 LCD5500 v1.X LCD5500Z v2.X LCD600 LED615 SL-XX PC1500RK PC1555RKZ PC5908 PC5928 PC5400 Printer/ DVACS Module v1.X to v2.1 PC5400 Printer/ DVACS Module v2.
