User Guide
6
7
ALARM MEMORY DISPLAY
[✱]+[3]
Press [✱] then [3] to enter the alarm memory mode. Any alarm caused during the
last armed period will be displayed. The “Alarm Memory” message will only be
displayed when an alarm occurred during the last armed period.
Press [#] to return to “READY”.
USER FUNCTIONS COMMAND
[✱]+[6]+[ACCESS CODE]
Enter [✱][6][Access Code] and then use the [<][>] keys to display the items of the
function menu. Press [✱] to select an item.
[0]Quick Arm [1]Quick Exit [2]Auto Arm Control [3]Keypad Setup
[4]Bell/Comm Test [5]Door Chime [6]Spec. Messages [7]User Call Up
[8]View Partitions
Item [0], [1], [5] and [6] turn on and off various functions. To enable or disable these
functions, press the [✱] key to toggle “Y ”or “N” on the keypad.
Y - The function is enabled
N - The function is disabled
QUICK ARM
[✱]+[6]+[ACCESS CODE]+[0]
The “Quick Arm” feature is enabled by toggling to “Y” on the keypad. When enabled
the panel can be armed by entering [✱][0]. One time use access codes should not
be used with the quick arm feature. The one time use code is only erased when used
to arm.
QUICK EXIT
[✱]+[6]+[ACCESS CODE]+[1]
The “Quick Exit” function is enabled by toggling to “Y” on the keypad. When enabled
the user can exit through any delay zone without altering the status of the system, by
entering [✱][0] on the keypad.
AUTO ARM CONTROL
[✱]+[6]+[ACCESS CODE]+[2]
This function must be enabled by the installer, or an error tone will sound when this
section is entered.
The PC4000 can be programmed to arm a partition at the same time each day, by
enabling the Auto Arm function and programming the Auto Arm time.
At the selected Auto Arm time, the system will give a pre-alert. The keypad begins
to sound and the Bell/Siren will pulse once every 10 seconds to alert anyone on the
premises that the system is about to arm. The Bell/Siren pulse can be programmed
by the installer to be silent.
The keypad will sound for one minute before Auto Arming unless the Auto Arm is
aborted. To abort the Auto Arm and silence the keypad press any key during the
pre-alert. The Auto Arm will be attempted at the same time the following day. The
PC4000 can be programmed to require a code to be entered for a user to abort the
Auto Arm by the installer.
Upon selecting the Auto Arm Control function, the Auto Arm Control menu will
appear on the LCD keypad.
[0] Auto Arm [1] Auto Arm Time
Auto Arm toggles “Y” or “N” to enable or disable the Auto Arm function.
Auto Arm time is the time the partition will automatically arm itself every day.
NOTE
: The Auto Arm time is a 24 hour clock and times must be entered as two digit
numbers.
E.g. HH - 01, 02,.....10,11,.....23,24
MM - 00, 01,.....35,36.....58,59
Enter 4 digits representing the time in hours and minutes (HH:MM) based on 24 hour
or military time. Always enter a leading zero where only one digit is required, 8:05 am
would be entered as 0805, 1:30 pm would be entered as 1330.
KEYPAD SETUP
[
]+[6]+[ACCESS CODE]+[3]
This function allows the user to adjust the backlighting and contrast of the LCD-4500
keypad. When this function is selected, the Keypad Setup menu will appear on the
keypad.
■
Bright Control
adjusts the level of backlighting on the LCD display and the
backlighting on the keys.
■
Contrast Control
adjusts the contrast of the lettering on the LCD display.
Use the [<][>] keys to toggle through the eight different settings, and press [✱] to
select the level of preference.
BELL/COMM TEST
[✱]+[6]+[ACCESS CODE]+[4]
This option allows the end user to test the system. The bell’s and keypad buzzer’s are
activated for two seconds and a test code transmission will send to the monitoring
station.
DOOR CHIME
[✱]+[6]+[ACCESS CODE]+[5]
The Door Chime feature is enabled or disabled by pressing the [✱] key to toggle from
“N” to “Y” or “Y” to “N”. When the chime zone is activated, the keypad will beep quickly
5 times. The “Beeping” on doors can be eliminated temporarily by using zone bypass,
only when the panel is disarmed.
SPEC. MESSAGES
[✱]+[6]+[ACCESS CODE]+[6]
This function enables two special event messages to be displayed when one of the
special events occurs.
The first message is “Fail to Arm”. It will be displayed if the user is unable to arm the
partition after entering a valid code (e.g., because of activity on the zones).
The second message is “Alarm When Armed”. It will be displayed if an alarm occurred
during the previous armed period.
The messages are programmed by the installer.
USER CALL UP
[✱]+[6]+[ACCESS CODE]+[7]
This function must be enabled by the installer. When selected, the panel will call the
downloading computer. The downloading computer must be waiting for the panel to
call before downloading can be performed.
Only use this function upon request from the installer.