User Guide

3
10
ARMING
Close all protected doors and windows and stop movement in areas covered by
motion detectors.
The “Enter Code to Arm System” message should be on the LCD display. The
system cannot be armed unless the “Enter Code to Arm System” or “Secure
System or Enter Code...” message is displayed.
Enter a [4 Digit Security Code]. As each digit is entered the keypad will beep.
■
If the security code was entered incorrectly, the keypad will beep steadily for 2
seconds.
■
If the code was entered correctly but the system was not secure due to an open
zone, the keypad will beep quickly followed by a steady tone.
■
When the correct code is entered, the “Exit delay in Progress” message will be
displayed and the keypad will beep quickly.
A timer will appear in the right side of the display indicating the remaining time
in the exit delay. Exit the premises through the designated exit-entry door. At the
end of the allowed exit time the message on the keypad will change to “Enter
Code to Disarm System”.
DISARMING
Enter the premises through the designated exit-entry door. The keypad buzzer
will be on. Go to the keypad and enter the [4 digit security code]. If an error is
made in entering the code, press the [#] key and enter the code again. The
“Armed” light will go out and the keypad buzzer will stop. The correct security
code must be entered before the allowed entry time expires. If an alarm
occurred while the panel was armed, the “View Memory” message will be on
the display with the zone name for the zone that caused the alarm. The display
will keep those messages on for two minutes or until the [#] key is pressed to
return the panel to the normal arm-disarm mode.
AUTO-BYPASS/HOME-AWAY ARMING
If a correct security code is entered and you do not exit the premises through a
designated exit-entry door, the system will, at the end of the Exit delay time, arm
with interior zones automatically bypassed if those interior zones have been
programmed as “Home-away” zones. These zones will remain bypassed until
[✱][1] is entered to reactivate bypassed home-away zones.
This is a convenience feature for someone who wishes to remain on the
premises with the system armed. That person does not have to manually bypass
the home-away zones.
To reactivate the Home-away zones that have been automatically bypassed,
press [✱][1]. This command is a quick method of fully arming the system in
residential applications before going to bed.
MAINTENANCE
With normal use, the system requires minimum maintenance. The following
points should be observed.
1.Do not wash the keypad with a wet cloth. Light dusting with a barely damp cloth
should remove normal accumulations of dust.
2.The battery/bell test is designed to determine battery condition, however it is
recommended that the stand-by batteries be replaced every three years.
3.For other system devices such as smoke detectors, passive infrared, ultrasonic or
microwave motion detectors or glassbreak detectors, consult the respective
manufacturer’s literature for testing and maintenance.
LIMITED WARRANTY
Digital Security Controls Ltd. warrants that for a period of twelve months from the
date of purchase, the product shall be free of defects in materials and
workmanship under normal use and that in fulfillment of any breach of such
warranty, Digital Security Controls Ltd. shall, at its option, repair or replace the
defective equipment upon return of the equipment to its factory. This warranty
applies only to defects in parts and workmanship and not to damage incurred in
shipping or handling, or damage due to causes beyond the control of Digital
Security Controls Ltd. such as lightning, excessive voltage, mechanical shock,
water damage, or damage arising out of abuse, alteration or improper
application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall
be in lieu of any and all other warranties, whether expressed or implied and of
all other obligations or liabilities on the part of Digital Security Controls Ltd. This
warranty contains the entire warranty. Digital Security Controls Ltd. neither
assumes, nor authorizes any other person purporting to act on its behalf to
modify or to change this warranty, nor to assume for it any other warranty or
liability concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any direct or indirect
or consequential damages, loss of anticipated profits, loss of time or any other
losses incurred by the buyer in connection with the purchase, installation or
operation or failure of this product.
WARNING
Digital Security Controls Ltd. recommends that the entire system be completely
tested on a regular basis. However, despite frequent testing, and due to, but not
limited to, criminal tampering or electrical disruption, it is possible for this
product to fail to perform as expected.