INSTALLATION MANUAL PC2525 Version 1.
TABLE OF CONTENTS FEATURES 1 SPECIFICATIONS 1 INSTALLATION 2 Mounting the Panel ................................................................................................................................................ 2 Mounting the Keypad ............................................................................................................................................. 2 Auxiliary Power Connection ..........................................................................................
[05] [06] [07] [08] [09] [10] [11] [12] [13] Second Master Code ................................................................................................................................... 13 Programmable Output Options ................................................................................................................... 14 Keypad Lockout Options .............................................................................................................................
FEATURES SPECIFICATIONS Keypad Programmable PC2525 Control Panel The PC2525 is complete with a default program so that it is operational with a minimum of programming. The control panel is completely programmable from the keypad. EEPROM Memory The panel uses EEPROM memory which will retain all program information even if AC and battery power is removed from the panel. The EEPROM memory can be reprogrammed thousands of times.
INSTALLATION Mounting the Panel Select a dry location close to an unswitched AC source and close to the telephone line connection. Remove the control panel, the mounting hardware and the keypad from the cardboard retainer inside the cabinet. Before attaching the cabinet to the wall, press the five circuit board mounting studs into the cabinet from the back. Once the cabinet is mounted to the wall, pull all the cables into the cabinet and prepare them for connection.
Fire Zone Wiring Any number of the 8 zones may be programmed as a Fire Zone; refer to Programming Section [01]. Smoke detectors should be the latching type and have normally-open alarm initiating contacts. A DSC RM-1 Relay should be used to connect power to the smoke detectors; refer to the hook-up diagram below. Power wiring from the AUX+ / PGM terminals should be supervised using a DSC RM-1 Relay connected after the last smoke detector.
GUIDELINES FOR LOCATING SMOKE DETECTORS Experience has shown that all hostile fires in family living units generate smoke to a greater or lesser extent. Experiments using typical fires in family living units indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke detectors should be installed outside of each sleeping area and on each additional story of the family unit.
KEYPAD FUNCTIONS Introduction The PC2550RK Keypad provides complete information and control of the PC2525 control panel. The panel can be fully programmed from the keypad. The 8 Zone Lights provide alarm and status indication for the alarm circuits. Each zone can be programmed to be a burglary zone or a fire zone. The 7 system lights guide the user in operating the system and the built-in sounder lets the user hear correct key entries and other alert signals.
Disarming Enter the premises through the designated entry-exit door. The keypad sounder will be on as a reminder to disarm the system. Go to the keypad and enter a valid Access Code. If an error is made entering the code, press the [#] key and enter the code again. The “Armed” light will go out and the sounder will stop. The correct Access Code must be entered before the entry time expires or the panel will go into alarm.
Trouble Conditions [∗ ]+[2] The PC2525 continuously monitors a number of trouble conditions. If one of these conditions occurs, the keypad “Trouble” light will come ON and the buzzer will sound 2 short beeps every 10 seconds. To silence the buzzer, press the [#] key. The buzzer will stop but the “Trouble” light will remain ON until the trouble condition is cleared. Refer to Programming Sections [39] and [40] for information on the trouble conditions that can be transmitted to the monitoring station.
User Programming Commands [∗ ]+[5]+[Master Code] ∗ The [ ][5] programming command allows the user to program Access Codes 2 through 8; the First Access Code is the Master Code. The factory default for the Master Code is “1234”. The 8th Access Code may be changed from a regular code to a One-Time Use Code by turning ON Zone Light 1 in Section [09]. The OneTime Use code allows an individual, such as a service person, to disarm and then re-arm the system.
Setting the Clock [∗ ]+[6]+[Master Code]+[1] The System Clock is a 24-hour clock. Hours and minutes must be entered as 2-digit numbers. • HH, hours: 00 to 23 MM, minutes: 00 to 59 8:05 AM would be entered as 0805; 1:30 PM would be entered as 1330 Setting the system clock tells the system the time of day. If the system is without power, (AC and battery), it cannot continue to keep time. When the panel is powered up, the system clock must be reset.
Utility Output Command [∗ ]+[7] or [∗ ]+[7]+[Access Code] The Programmable Output (PGM terminal) can be programmed for activation by a keypad command. This output can be used to operate other devices such as door openers, special lighting, door strikes or to reset smoke detectors. Refer to Programming Section [09] Light 5. Depending on the option selected, the [ ][7] command may require that an Access Code be entered to activate the Utility Output.
PROGRAMMING Introduction The PC2525 is fully keypad-programmable, and also supports downloading programming functions. The system’s EEPROM memory can be reprogrammed thousands of times and will not lose program data even after total loss of power. This section of the manual describes how to program the PC2525 using the system’s keypad. Programming ∗ With the system disarmed, enter [ ][8][Installer’s Code]; note that the system can only be programmed while it is disarmed.
SYSTEM PROGRAMMING SECTIONS [00] Binary Programming This section is normally used upon instruction from factory technical personnel for specialized programming not covered by the standard programming instructions. [01] Zone Definitions Program eight 2-digit numbers in this section. The first digit determines the audible characteristics of the zone, while the second digit determines the zone’s operation.
To restore the smoke detectors to normal, clear all products of combustion from the detectors and perform a reset by pressing the [ ] then [7] keys. See Section [06] for programming the PGM terminal for smoke detector reset. Pressing [ ][7] will remove power from the smoke detectors for 5 seconds; if the detectors are clear of smoke, they will return to normal. If the detectors still have smoke in them, the alarm will resound and the sequence described above will repeat.
[06] Programmable Output Options The PGM terminal can be programmed to operate in response to various system operations. The output pulse connects the PGM terminal to the negative power rail. The switching transistor used for this purpose can sink up to 55 mA. [00] 2-Wire Smoke Detectors When programmed as [00], the PGM output will be programmed for use with 2-wire smoke detectors. Refer to the Hook-Up Diagram for instructions on connecting 2-wire smoke detectors.
[07] Keypad Lockout Options This section determines how the Keypad Lockout function operates. The first number determines how many invalid Access Codes need to be entered to lockout the keypad; enter a 2-digit number from 00 to 99. The second number determines how long, in minutes, the keypad will be locked out. Enter a 2-digit number from 00 to 99. Programming either of the numbers in the section as 00 will disable the keypad lockout feature.
[09] Second System Option Code Zone Light 1: One Time Use Code Option ON: One Time Use Code Enabled. Access Code 8 may be used to disarm and then later arm the system only once. After the One Time Use Code is used to arm the system, it will be deleted and will not be able to arm or disarm the system. • OFF: One Time Use Code Disabled. Access Code 8 functions as a normal Access Code. Zone Light 2: Master Code Options ON: Master Code Not User-Changeable.
[10] Third System Option Code Zone Light 1: 2-minute Keypad Time-out Enabled / Disabled ON: 2-minute Keypad Time-out Enabled. If no keys are pressed for 2 minutes, all keypad lights will be shut OFF. NOTE: The 2-minute Keypad Timeout must not be selected if the LCD600 Keypad or the Escort Voice Assisted Security Control Module is used with the PC2525. • OFF: No Keypad Time-out. The keypad lights will remain ON at all times. Zone Light 2: [F] Key Enabled / Disabled ON: [F] Key Disabled.
[11] Fourth System Option Code Zone Light 1: Bell Pulse Options ON: Bell Pulses for All Alarms. The bell or siren will pulse for all types of audible alarms. • OFF: Bell Pulses for Fire Alarm Only. The bell or siren will pulse for Fire and [F] Key alarms. For all other audible alarms, the bell or siren will sound a steady alarm. Zone Light 2: Bell Squawk on Exit Delay Options ON: Bell Squawk on Exit Delay. The Bell output will pulse during the Exit Delay Time. • OFF: No Bell Squawk on Exit Delay.
COMMUNICATIONS PROGRAMMING SECTIONS [30] First Telephone Number This is the first telephone number the Communicator will dial. After entering Section [30], enter the telephone number the same way you would dial it on a touch-tone phone. Press [#] after the last digit to complete the telephone number programming.
[35] Restoral Reporting Codes, Zones 1 - 8 These reporting codes are used by the communicator to transmit zone restorals for zones 1 through 8. Program 8 2-digit numbers in this section. [36] Closing (Arming) Reporting Codes for Access Codes 1 - 8 Reporting codes 1 to 8 are used to identify closings for Access Codes 1 to 8.
[42] Communication Variables Enter four 2-digit numbers in this section; do not press the [#] key while entering data. Swinger Shutdown (number of transmission) This value defines the number of attempts (alarm and restoral pairs) per zone that the communicator will make before it shuts down for that zone (“swinger shutdown”). Program a 2-digit number form 00 to 99. When programmed as 00, the communicator will not be shut down and all alarms will be transmitted.
3 All other non-alarm reporting codes must be set up to send an extended 2nd round. The 1st digit of the reporting code is used to identify the event while the 2nd or extended digit is used to associate the event with a particular item (for example, a reporting code of E3 means restore zone 3; E for restore and 3 for zone 3).
[46] First Communicator Option Code Zone Light 1: Communicator Disabled / Enabled ON: Communicator Disabled. The system’s communicator will be shut off and events will not be transmitted to the monitoring station. • OFF: Communicator Enabled. The system’s communicator will be enabled and all events with reporting codes will be reported to the monitoring station. Refer to the Telephone Number, Reporting Code and Call Direction Programming Sections.
Zone Light 8 Closing Confirmation Enabled / Disabled ON: Closing Confirmation Enabled. When an Access Code is entered to arm the system, the Exit Delay time will not begin until one of the following events occurs: • The closing is successfully transmitted to the monitoring station. When the closing is transmitted, the keypad will sound an acknowledgement tone to indicate that the monitoring station has been advised of the closing. The Exit Delay will then begin.
DOWNLOADING PROGRAMMING SECTIONS [70] First Downloading Option Code Zone Light 1: Downloading Answer Enabled / Disabled ON: Downloading Answer Enabled. The system will answer calls for downloading after the number of rings programmed in Section [74]. • OFF: Downloading Answer Disabled. The system will not answer incoming calls. With Downloading Answer disabled, downloading must be performed with the User Call-up or Periodic Downloading functions.
LOCKOUT AND RESET SECTIONS [90] Installer Lockout Enable When this feature is enabled, performing a hardware or software reset to restore the system’s factory programming will not reset the Installer’s Code or the Downloading Access Code. To enable this feature, enter Section [90]. After entering Section [90], enter [Installer’s Code][90] to confirm activation of this feature.
FOR THE RECORD Customer _________________________________________________________________________________________ Address _________________________________________________________________________________________ _________________________________________________________________________________________ Phone ___________________________________________ Installation Date ___________________________ CONTACTS: #1 Name ___________________________________________ Phone ____________________________________ #2
PC2525 v1.
PC2525 V1.1 [07] Keypad Lockout Options Page 15 Default I__0 ____I__0 ____I I_______I_______I Number of Invalid Codes before Lockout I__0 ____I__0 ____I I_______I_______I Lockout Duration (minutes) [08] First System Option Code Default I___OFF ________I Enter two 2-digit numbers in the range of 00 to 99. Program the number of Invalid Codes as 00 to disable the lockout feature.
PC2525 v1.
PC2525 V1.
PC2525 v1.
PC2525 v1.
PC2525 v1.1 [74] Number of Rings Before Answering Page 25 Default I__1 ____I__2 ____I I_______I_______I Valid entries are [01] to [12] [75] Answering Machine Double-Call Timer Page 25 Default I__0 ____I__6 ____I__0 ____I I_______I_______I______I Valid entries are [001] to [249] [76] LINKS1000 Preamble (Downloading Telephone Number) I______I______I______I______I Program all unused digits with hexadecimal “F”.
HOOK-UP DIAGRAM 2-Wire Smoke Detector Information: Zone Identifier: PFA1 Type Zone: Standard Loop Style: Class B, Style B Maximum Line Resistance: 100Ω total End of Line Device: EOLR-1, 1000Ω 0.
LIMITED WARRANTY Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shall be free of defect in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot.
37
© 1995 Digital Security Controls Ltd.
