Specifications

KEYPADVCOMMANDS
9
the Bypass (or System) light will be ON while the system is armed
to indicate any bypassed zones (see Section 5.17 “Arming /
Disarming Options”).
Zones can only be bypassed when the system is
disarmed.
To bypass a zone:
1. Enter [✱]
[1] (and an access code, if required).
2. The keypad will flash the Bypass (or System) light. The zone
indicator lights corresponding to any zones already bypassed
will turn ON.
3. Enter the 2-digit zone number for the zone you wish to
bypass. The corresponding zone indicator light will turn ON.
4. Press [#] to exit the function. All zones whose indicator lights are
ON when the [#] key is pressed will be bypassed. The Bypass (or
System) light will turn ON, indicating that one or more zones are
bypassed.
To Activate a bypassed zone:
1. Enter [✱]
[1] (and an access code if required).
2. The keypad will flash the Bypass (or System) light. The zone
indicator lights corresponding to any zones already bypassed
will turn ON.
3. Enter the 2-digit zone number for the bypassed zone you
wish to reactivate. The corresponding zone indicator light
will turn OFF.
4. Press [#] to exit the function. All zones whose indicator lights
are ON when the [#] key is pressed will be bypassed. If no
zone indicator lights were ON, the Bypass (or System) light
will be OFF and no zones will be bypassed.
When the system is disarmed, all manually-
bypassed zones will be unbypassed.
Activate Stay/Away Zones
If the system is armed in the Stay mode
, the [✱] [1] command can
be used to activate the Stay/Away zones.
[✱]
[2] Trouble Display
The panel constantly monitors itself for several different trouble
conditions. If a trouble condition is present, the Trouble (or System)
light will be ON and the keypad will beep twice every 10 seconds.
The trouble beep can be silenced by pressing any key on any
keypad. If Bell Squawk on Trouble is enabled (section [014],
option[5]), the bell will squawk every 10 seconds when a trouble
condition is present.
To view trouble conditions from an LED keypad:
1. Press [✱]
[2].
2. The keypad will flash the Trouble (or System) light. The zone
indicator lights corresponding to the present trouble conditions
will be ON.
When using an LCD keypad, the trouble conditions will be listed
on the display; the user must simply use the arrow (< >) keys to
scroll through the list of present trouble conditions.
Troubles can be viewed while armed using the
LCD keypad, provided it is version 2.0 or later.
Older keypads will incorrectly display “Fire
Trouble”. If using older LCD keypads, program-
ming section [013], option [3] as OFF will ensure
troubles are displayed correctly.
The various troubles are described below:
Trouble [1] – Service Required
If zone indicator light [1] is ON, a “service required” trouble is
present. Press [1] to determine the specific trouble. The following
is a list of “service required” trouble conditions:
• Light [1] – Low Battery: The main panel backup battery is low.
The trouble will be generated if the battery drops below 11.5
volts under load and will be restored when the battery charges
over 12.5 volts.
• Light [2] – Bell Circuit Trouble: The panel will indicate this
trouble if the panel senses an open condition on the bell circuit
(see Section 5.13 “Siren”).
• Light [3] – General System Trouble: This trouble will be
present if the printer connected to the PC5400 Printer module
has a fault and is off-line.
• Light [4] – General System Tamper: This trouble will be
indicated if any peripheral module tamper is detected.
Entering and exiting Installer’s Programming will
not reset the system tampers. All tamper
conditions must be physically restored.
• Light [5] – General System Supervisory: This trouble will be
indicated if the panel loses communication with any module
connected to the Keybus (see Section 2.6 “Supervision”). The
event buffer will log a detailed description of the event.
• Lights [6-8] – For future use
Trouble [2] – AC Failure
This trouble indicates that AC power is no longer being supplied
to the control unit. The trouble LED will flash if an AC Failure is
present, if the Trouble Light Flashes if AC Fails option is
programmed (section [016], option [2]). This trouble will not be
displayed if the AC Trouble Displayed option is disabled
(section [016], option [1]).
The reporting codes in sections [349] and [350] can be
programmed to communicate a power failure to the monitoring
station. To avoid reporting short power failures, an AC Failure
Communication Delay from 000-255 minutes can be
programmed in section [370].
Trouble [3] – Telephone Line Monitoring Trouble (TLM)
The telephone connection to the control unit is checked every 10
seconds. If TLM is enabled, the minimum number of checks is
three. If the voltage drops below one to three volts for three
checks, plus the number of consecutive checks programmed in
section [370], a telephone line trouble is generated. If the
system has a LINKS 1000, this trouble can be reported to a
monitoring station by programming reporting codes in sections
[349] and [350]. (See section 5.12 “Telephone Line Monitor”.)
Trouble [4] – Failure to Communicate (FTC)
This trouble will be generated if the communicator fails to
communicate with any of the programmed telephone numbers.
If a later attempt is successful, the FTC reporting code(s)
programmed in section [351] will be transmitted along with the
unreported events from an earlier unsuccessful communication.
Trouble [5] – Zone Fault (including Fire Zone)
This trouble will be generated if any zone on the system is
experiencing trouble, meaning that a zone could not provide an
alarm to the panel if required to do so (if a fire zone is open, or
there is a short on a DEOL zone, or a supervisory fault on a
wireless zone). When a zone fault trouble condition occurs, the
keypad(s) on the system will start to beep.
Press [5] while in Trouble mode to view the affected zones. If 2-
wire smoke detectors are being used, a trouble on that zone will
be indicated by the “Fire” LED.
A Fire zone trouble will be generated and dis-