Specifications

KEYPADVCOMMANDS
10
played in the armed state. A Fire zone trouble will
also restart the trouble beeps from all keypads.
Trouble [6] – Zone Tamper
This trouble is only generated by zones configured for Double
End Of Line resistor supervision when a tamper condition is
present, or when the tamper switch is open on a wireless device.
When a tamper condition occurs, the keypad(s) will start to
beep. Press [6] while in the Trouble mode to view the affected
zones. If a zone is tampered or faulted, it must be fully restored
to clear the trouble.
Trouble [7] – Device Low Battery
This trouble is generated when a wireless device exhibits a low
battery condition. Press [7] one, two, or three times to view which
devices are experiencing battery failure. An LED keypad will
indicate battery failure using zone lights 1 to 8.
The following then will occur:
Keypad beeps: Keypad displays:
Press [7] 1 Zones with low batteries (LED
keypad - zone lights 1 to 8)
Press [7] again 2 Handheld keypads with low
batteries (LED keypad - zone
lights 1 to 4)
Press [7] again 3 Wireless keys with low
batteries (LED keypad - zone
lights 1 to 8)
To view the battery conditions
of wireless keys 9 through 16,
you must be at an LCD keypad.
Trouble [8] – Loss of System Time
When the panel is powered up, the internal clock needs to be set
to the correct time. This trouble is cleared when an attempt is
made to reset the clock.
[✱]
[3] Alarm Memory
The Memory (or System) light will be on if any alarm occurred
during the last armed period or – in the case of 24 hour zones –
if an alarm occurred while the panel was disarmed.
To view alarm memory, press [✱]
[3]. The keypad will flash the
Memory (or System) light and the zone indicator lights corresponding
to the alarm or tamper conditions which occurred during or since the
last armed period. To clear the Memory (or System) light, arm and
disarm the system.
[✱]
[4] Door Chime On/Off
The door chime feature is used to sound a tone from the keypad
whenever a zone programmed as a chime zone is activated (see
Section 5.3 – “Zone Attributes”). If the door chime feature is
enabled, the keypad will emit five short beeps whenever a chime
zone is activated. Designated entry/exit doors are often defined
as chime zones. When the feature is enabled, the keypads will
sound when an entry/exit door is opened. The feature can be
turned on or off while the system is armed.
To turn Door Chime ON or OFF:
1. Press [✱]
[4].
2. The keypad will emit three short beeps if the Door Chime
feature is enabled and one long beep when disabled.
The function can also be performed by pressing and holding the
Chime function key for two seconds on any keypad with function
keys.
[✱]
[5] Programming Access Codes
There are 37 access codes available to the user. They are:
Access code (40) ............. One master code
Access codes (01)-(32) ... 32 general access codes
Access codes (33)-(34) ... Two duress codes
Access codes (41)-(42) ... Two supervisor codes
All access codes have the ability to arm or disarm the system
and can activate the PGM Outputs using the [
✱] [7] commands.
Master Code – Access Code (40)
By default, the Master Code is enabled to perform any keypad
function. This code can be used to program all User Codes. If the
Master Code Not Changeable option is enabled, the Master
Code can only be changed by the Installer.
General Access Codes – Access Codes (01) to (32)
General access codes can arm and disarm the system. When
the Code Required for Bypassing option is enabled, users will
need to enter a valid access code when bypassing zones.
Individual access codes can have the Zone Bypassing attribute
disabled under Access Code Attribute programming.
For more information regarding access code options, please
see Section 5.1 – “Programming Security Codes.”
Duress Code – Access Code (33) and (34)
Duress codes will send a duress reporting code to the central
station when entered.
A duress code, if programmed, will always send a
reporting code to the central station, even if its
attributes are turned off.
Supervisor Codes – Access Code (41) and (42)
The two supervisor codes have master code attributes by
default. These settings can be changed.
How to Program Access Codes from an LED Keypad:
1. Enter [✱]
[5] [Master Code]. The keypad will flash the
Program (or System) light.
2. Enter the 2-digit number corresponding to the code you wish
to program.
3. Enter a 4-digit code.
4. Continue from step 2 until all codes are programmed. Once
the process is complete, press the [#] key to return to the
Ready state.
Do not press [ ✱ ] or [#] when programming the
4-digit code.
How to Program Access Codes from an LCD Keypad:
1. Enter [✱]
[5] [Master Code]. The display will read “(✱) to Edit
User Code 01P”. [01P] represents the first access code. “P”
indicates that the access code is programmed. If the access
code is not yet programmed, a “—” will be displayed instead
of a “P”.
2. Use the scroll keys (< >) to find the access code you wish to
add, change or delete (indicated by “XXP” if programmed, or
“XX—” if not programmed, where XX = user number). Press
the [
✱] key to select the code you wish to alter. The display
will read “Enter New Code AAAA”.
3. To add or change a code, enter the new code. Access codes
must be four digits. Enter digits 0 through 9 only. Once the 4
digit code has been entered, the keypad sounder will beep
3 times and the display will read “(✱) to Edit User Code 01P”.
The “P” means the code has been programmed.
4. Press [#] to exit the code programming function.
How to Erase an Access Code:
Enter [✱]
[5] [Master Code], select the code to be erased and
press [✱].
Access Code Attributes
There are two access code attributes which can be programmed