Specifications

ManualsBrandsDSC ManualsOtherPC 1555

1.1 Specifications

Downloading Software Support

• PC1555 uses DLS-1 v6.3 and up

Flexible Zone Configuration

• Six fully programmable zones; system expandable to eight

zones using keypad zone inputs and wireless zones

• 38 access codes: one master code, one maintenance code,

two duress codes, two supervision codes and 32 general

access codes

• 27 zone types; 8 programmable zone attributes

• Normally closed, single EOL and double EOL zone wiring

• Eight wireless zones available using the PC5132 Wireless

Receiver

Audible Alarm Output

• Supervised Bell Output (current limited at 3 amps), 12V

• Steady or Pulsed Output

EEPROM Memory

• Does not lose programming or system status on complete AC

and Battery failure

Programmable Outputs

• One programmable voltage output and one programmable

voltage output/input; 21 programmable options

• PGM1 = 50mA; PGM2 = 300mA

Powerful 1.5 Amp Regulated Power Supply

• 550 mA Auxiliary Supply, 12 V

• Positive Temperature Coefficient (PTC) components replace

fuses

• Supervision for loss of AC power, low battery

• Internal clock locked to AC power frequency

Power Requirements

• Transformer = 16.5 V

AC, 40VA

• Battery = 12 volt 4 Ah minimum rechargeable sealed lead

acid battery

Remote Keypad Specifications

• Three keypads available:

- PC1555RKZ eight zone LED keypad with zone input

- PC5508Z eight zone LED keypad with zone input

- LCD5500Z Alphanumeric keypad with zone input

• All keypads have five programmable function keys

• Connect up to eight keypads

• 4-wire (Quad) connection to Keybus

• Built in piezoelectric buzzer

Digital Communicator Specifications

• Supports major communication formats including SIA and

Contact ID

• Event-initiated personal paging

• Three programmable telephone numbers

• Two account numbers

• Supports LINKS1000 cellular communication

• Supports LINKS2X50 Long Range Radio Transmitter

• DTMF and pulse dialing

• DPDT line seizure

• Anti-jam feature

• Split reporting of selected transmissions to each telephone

number

System Supervision Features

The PC1555 continuously monitors a number of possible trouble

conditions including:

• AC power failure

• Trouble by zone

• Tamper by zone

• Fire trouble

• Telephone line trouble

• Failure to communicate

• Low battery condition

• Bell output trouble

• Module fault (supervisory or loss of internal clock)

• AUX Power Supply Trouble

False Alarm Prevention Features

• Audible Exit Delay

• Audible Exit Fault

• Communication Delay

• Urgency on Entry Delay

• Quick Exit

Additional Features

• Auto Arm at specified time

• Keypad-activated alarm output and communicator test

• All modules connect to the system via a four wire Keybus up

to 1000’/330m from main panel

• An event buffer which records the past 128 events with both

the time and date at which they occurred; buffer can be

printed using PC5400 serial interface module, or viewed with

the LCD5500Z keypad.

• Supports the addition of the PC5132 Wireless receiver for

integration of wireless devices

• Uploading and downloading capability

• Local downloading capability through the use of the PC-LINK

adaptor

• Added Keybus fault protection: clock and data outputs have

been programmed to withstand shorts to +12v to prevent

control panel damage

System Introduction

S E C T I O N 1

Summary of content (52 pages)

PAGE 1
System Introduction S 1.
PAGE 2
S 1.2 Y S T E M V I N T R O D U C T I O N WLS910 Wireless Handheld Keypad The wireless handheld keypad can be used in conjunction with the PC5132 Wireless Receiver to include a simple and mobile method of arming and disarming the system. The unit comes with three ‘AAA’ batteries. The PC1555 system can have a maximum of four wireless handheld keypads.
PAGE 3
Getting Started S E C T I O N 2 The following sections provide a thorough description of how to wire and configure devices and zones. Programming Worksheets should be filled out completely before attempting to program the system. 2.1 Step 10: Testing the System The panel must be thoroughly tested to ensure that all features and functions are operating as programmed. Installation Steps The following steps are provided to assist you with installing the panel.
PAGE 4
G E T T I N G S Programmable Output Terminals – PGM1 and PGM2 Each PGM output is designed so that when activated by the panel, the terminal will switch to ground. PGM1 can sink up to 50mA of current. Connect the positive side of the LED or buzzer to AUX+, the negative side to PGM1. If more than 50 mA of current are required, a relay must be used. Please study PGM wiring in the accompanying diagram.
PAGE 5
G E T T I N G S activation or alarm—and include the proper values for loading calculations. Connected devices must not exceed system capabilities during any possible operational mode. 2.5 2.8 T A R T E D Zone Wiring For a complete description of the operation of all zone types, please refer to Section 5.2 (“Zone Programming”). There are several different ways in which zones may be wired, depending on which programming options have been selected.
PAGE 6
G E T T I N G S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ T A R T E D 4-Wire Smoke Detectors All fire zones must be wired according to the following diagram: End of Line Resistors ................................. Section [013]: [1] Single End of Line Resistors ......................
PAGE 7
G E T T I N G S T A R T E D To install the keypad, open the keypad plastic by removing the screw at the bottom of the unit. Locate the five terminals on the keypad circuit board. Connect the four Keybus wires from the control panel: the red wire to R, the black to B, the yellow to Y and the green to G. To connect the zone, run one wire to the Z terminal and the other to B. For powered devices, use red and black to supply power to the device.
PAGE 8
Keypad Commands S E C T I O N 3 The PC1555 alarm panel can be accessed, controlled and completely programmed via any keypad on the system. LED keypads (PC1555RKZ and PC5508Z) use function and zone indicator lights to represent alarm functions and status. The LCD keypad (LCD5500Z) provides a written description on the liquid crystal display and uses function indicator lights to communicate alarm status to the user.
PAGE 9
K E Y P A D V C the Bypass (or System) light will be ON while the system is armed to indicate any bypassed zones (see Section 5.17 “Arming / Disarming Options”). O M M A N D S is a list of “service required” trouble conditions: • Light [1] – Low Battery: The main panel backup battery is low. The trouble will be generated if the battery drops below 11.5 volts under load and will be restored when the battery charges over 12.5 volts.
PAGE 10
K E Y P A D V C played in the armed state. A Fire zone trouble will also restart the trouble beeps from all keypads. O M M A N D S Access codes (33)-(34) ... Two duress codes Access codes (41)-(42) ... Two supervisor codes All access codes have the ability to arm or disarm the system and can activate the PGM Outputs using the [ ✱] [7] commands.
PAGE 11
K E Y P A D V C O M M A N D S (<>) to scroll through the events in the buffer. When you have finished viewing the Event Buffer, press the [#] key to exit. for each code. To program each attribute, enter [✱] [5] [Master Code] [9] to enter the attribute programming mode. Then enter the code number [01-32,33,34,41,42]. Enter the attribute number: Attribute [1] ... User enabled for arming, disarming, alarm reset, [✱] [7] [1-2] options, auto arm cancellation Attribute [2] ...
PAGE 12
K E Y P A D V C after two minutes, the panel will begin the entry delay. M M A N D S [08] – [ ✱] [1] Bypass Mode This function key provides the user with a simple method for entering the Bypass Mode. If a user code is required, it must be entered before zone bypassing can be performed. If the Exit Delay is in progress, performing a Quick Exit will not extend the Exit Delay. 3.
PAGE 13
How to Program S E C T I 4.2 The following section of the manual describes the Installer’s Programming function and how to program the various sections. N 4 Programming Decimal Data A set number of programming boxes are allotted for each section requiring decimal data (e.g.: codes, telephone numbers). If a digit is entered for each program box, the panel will automatically exit from the selected programming section. The Ready light will turn OFF and the Armed light will turn ON.
PAGE 14
H 4.4 O W V T O V P Programming Toggle Option Sections O G R A M The keypad displays the information using a binary format, according to the following chart: Some programming sections contain several toggle options. The panel will use zone lights 1 through 8 to indicate if the different options are enabled or disabled. Press the number corresponding to the option to turn it ON or OFF.
PAGE 15
Program Descriptions S E C T I Programming Security Codes There are three codes which can be programmed by the installer in the Installer’s Programming function: the Master code, the Installer’s code, and a Maintenance code. All other access codes can be programmed through the [✱] [5] command (see Section 3.4). The master code can also be programmed by the user as access code (40). If the Master Code Not Changeable option is enabled, the system master code can only be changed by the installer.
PAGE 16
P R O G R A M D E S C R I P T I O N S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ “System Times”), or until a code is entered (see Section 5.13 “Siren”). A violated Fire zone will be displayed on all keypads. Typically this zone is used for pull stations. Zone Definitions ............................................................. [001] Zone Assignments .........................................................
PAGE 17
P R O G R A M D E S C Keypad Zone Assignments ........................................... [020] T I O N S Phone numbers can be up to 32 digits. This allows you to add special digits, if required. To program the phone number, enter the numbers 0 through 9 as required.
PAGE 18
P R O G R A M D E S C R I P T I O N S • Disarming using the maintenance code • Disarming via the DLS software • Disarming via keyswitch If an alarm occurred while the system was armed, an Opening After Alarm reporting code will be sent along with an opening reporting code when the user disarms the system. An Opening by Duress reporting code will be transmitted in addition to the duress reporting code if the system is disarmed using a Duress code.
PAGE 19
P R O G R A M D E S Maintenance The panel will transmit a Battery Trouble Alarm reporting code when the backup battery charge drops below 11.5 VDC . The Battery Trouble Restoral reporting code will not be transmitted until the battery has been charged to over 12.5 VDC .
PAGE 20
P R O G R A M D E S Installer Programming is entered. When using the SIA FSK communication format with Activity Delinquency, the Closing Delinquency identifier is transmitted. R I P T I O N S 3. Substitute the HEX digit ‘A’ for the ‘0’. 4. To prevent the panel from reporting an event, the reporting code should be programmed as [00] or [FF]. Please refer to Appendix A for a list of Contact ID Identifiers.
PAGE 21
P R O G R A M D E S C R I P T I O N S LINK, refer to your “PC-LINK Download Kit Instruction Sheet”. Downloading can also be performed through the LINKS 1000 cellular communicator, if the phone line is disconnected. If using the LINKS1000 with Call Back, you will need to program the LINKS 1000 Preamble with the downloading phone number in order for the panel to call the computer correctly. The Pager Format cannot be used with the LINKS 1000 cellular communicator.
PAGE 22
P R O G R A M D E S C R I P T I O N S This output can be used to indicate that an alarm has occurred before entering the premises. The PGM attributes for this option, programmed in Sections [141] to [142], differ from the standard selection of attributes. Program which events will activate the output by selecting some or all of the following attributes: Attribute [1] ........ Burglary (Delay, Instant, Interior, Stay/Away and 24 Hour Burglary Zones) [2] ........
PAGE 23
P R O G R A M D E S switch to ground at the beginning of the exit delay. The output goes high (open) when the panel is disarmed. C R I P T I O N S Attribute OFF: the output will turn ON and OFF when initiated by the user. (only applicable to options [19]-[20]) [5] ........... Access Code Req. No code Req. Attribute ON: the output requires a code for activation. Attribute OFF: no code required.
PAGE 24
P R O G R A M D E S C R I P T I O N S Communication of the signal to central station is immediate. on, one second off cadence. If Fire Bell Continuous is enabled, the alarm output will sound until a code is entered. If disabled, the alarm will sound until a code is entered or the bell cut-off time has expired. If the [A] / Key is pressed and held for two seconds, the panel will sound the keypad beeps three times to verify activation.
PAGE 25
P R O G R A M D E S Bypass Status Displayed While Armed ..... Section [016]: [7] C R I P T I O N S counter. Swinger shutdown will be reset every day at midnight or when the panel is armed. Once reset, the panel will again communicate normally. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5.18 Entry/Exit Delay Options Two different Entry Delays can be programmed: the first entry delay will be enabled for Delay 1 type zones and the second for Delay 2 type zones.
PAGE 26
P R O G R A M D E S C R I P T I O N S • the panel will try to call using land lines – if unsuccessful, the panel will try to call using the LINKS • if unsuccessful, the panel will try to call using the land lines on the next dialing attempt This process will continue until the panel has successfully communicated with the central station or until the panel’s dialing attempts have been exhausted. 5.
PAGE 27
P R O G R A M D E S I P T I O N S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Installer Lockout Enable ................................... Section [990] Installer Lockout Disable .................................. Section [991] AC power must be used to power the panel. The panel will not default if only the battery is used. ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5.
PAGE 28
Programming Worksheets For the Record Customer: ___________________________________________________________________________________________ Address: ____________________________________________________________________________________________ Phone: ________________________________________________ Installation Date: _______________________________________ Installer’s Code: ________________________________________________________________________________________________ Module Name Description Location PC15
PAGE 29
P R O G R A M M I N G W O R K S H E E T Keypad Programming [000] Keypad Enrollment (Section 2.5 “Keypad Enrollment”) NOTE: This must be done at each keypad requiring programming. [0] Slot [Valid entries are 11-18; ie. enter [11] for slot 1, [12] for slot 2, etc.
PAGE 30
P R O G R A M M I N G W O R K S H E E Basic Programming Zone Definitions 00 Null Zone (Not Used) 01 Delay 1 02 Delay 2 03 Instant 04 Interior 05 Interior, Stay/Away 06 Delay, Stay/Away 07 Delayed 24 Hour Fire (Hardwired) 08 Standard 24 Hour Fire (Hardwired) 09 10 11 12 13 14 15 16 17 24 Hour Supervisory (LINKS) 24 Hour Supervisory Buzzer 24 Hour Burglary 24 Hour Holdup 24 Hour Gas 24 Hour Heat 24 Hour Medical 24 Hour Panic 24 Hour Emergency 18 19 20 21 22 23 24 87 88 24 Hour Sprinkler
PAGE 31
P R O G R A M M I N G W O R K S H E E T [009] PGM Output Programming (PGM 1 and 2) (Section 5.
PAGE 32
P R O G R A M M I N G W [015] Third System Option Code Default Option ON O R K S H E OFF E T S Section ON I________I 1 Fire Keys Enabled Fire Keys Disabled 5.16 OFF I________I 2 Panic Keys Audible (Bell / Beeps) Panic Keys Silent 5.16 OFF I________I 3 Quick Exit Enabled Quick Exit Disabled 3.4 ON* I________I 4 Quick Arming Enabled Quick Arming Dis. / Function keys Req. Code3.4 OFF I________I 5 Code Required For Bypassing No Code Required 3.
PAGE 33
P R O G R A M M I N G W O R K S H E E T S Advanced System Programming Zone Attributes (Section 5.3 “Zone Attributes”) Zone Attribute Defaults (Y = Option ON; N = Option OFF): Attribute: 1 2 3 4 5 6 7 8 ON Audible Steady Chime Bypass Force Swing Tx. Delay Wireless Zn. OFF Silent Pulsed No No No No No No 00 Null Zone 01 Delay 1 02 Delay 2 03 Instant 04 Interior N Y Y Y Y N Y Y Y Y N Y Y Y N N Y Y Y Y N N N N N N Y Y Y Y N N N N N N N N N N 05 Int.
PAGE 34
P R O G R A M M I N G W O R K S H E E T S PGM Output Attributes (Section 5.11 “PGM Output Options”) Program only the following attributes for the PGM Options listed. All others will be ignored. PGM Options are programmed in section [009]. PGM Attribute Defaults (Y = Attribute ON; N = Attribute OFF): Attribute: ON OFF 1 2 3 4 5 Output enabled Output disabled — — True Output Inverted 5 sec. pulse On / Off Code Req. No Code Req. PGM Option [01] Burg.
PAGE 35
P R O G R A M M I N G W O R K S H E E T S [202] Zone Assignments (Section 5.2 “Zone Programming”) Program Zone Definitions in section [001] and Zone Attributes in sections [101] - [108]. Program Keypad Zone Assignments in section [020]. Any zones not used on the system should be disabled in this section. Disabled wireless zones should have a blank serial number (ie. [000000]).
PAGE 36
P R O G R A M M I N G W O R [329] Priority Alarm and Restoral (Section 5.8 “Communicator – Reporting Codes”) I_______I_______I Keypad Fire Alarm I_______I_______I Keypad Fire Restoral I_______I_______I Keypad Auxiliary Alarm I_______I_______I Keypad Auxiliary Restoral I_______I_______I Keypad Panic Alarm I_______I_______I Keypad Panic Restoral I_______I_______I PGM2 Alarm I_______I_______I PGM2 Restoral [330] Tamper Reporting Codes, Zones 1-8 (Section 5.
PAGE 37
P R O G R A M M I N G W O R K S [343] Miscellaneous Closing (Arming) Reporting Codes (Section 5.
PAGE 38
P R O G R A M M I N G W O R K S H E E [351] Miscellaneous Maintenance Reporting Codes (Section 5.
PAGE 39
P R O G R A M M I N G W O R K S H E E T [367] System Maintenance Alarm/Restore Communicator Call Directions (Section 5.5 “Communicator – Dialing”) Default ON OFF OFF OFF OFF I________I I________I I________I I________I I________I Option 1 2 3 4 5-8 ON 1st Telephone Number 2nd Telephone Number 1st Telephone Number (via LINKS) 2nd Telephone Number (via LINKS) For Future Use OFF Disabled Disabled Disabled Disabled [368] System Test Transmissions Communicator Call Directions (Section 5.
PAGE 40
P R O G R A M M I N G W [381] Second Communicator Option Code Default Option ON O R K S H E OFF E Section OFF I_______I 1 Open After Alarm Kypd Ringback enabled Open After Alrm Kypd Ringback disabled 5.17 OFF I_______I 2 Open After Alarm Bell Ringback enabled Open After Alrm Bell Ringback disabled OFF I_______I 3 SIA Sends Programmed Rep. Codes SIA Sends Automatic Rep. Codes 5.9 OFF I_______I 4 Closing Confirmation Enabled Closing Confirmation Disabled 5.
PAGE 41
P R O G R A M M I N G W O R K S H E [406] Number of Rings to Answer On (Section 5.10 “Downloading”) Default: 000 I_______I_______I_______I (Valid entries are 000-255 rings) [490] LINKS Preamble (Downloading Telephone Number) (Section 5.10 “Downloading”) Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F) [499] [Installer’s Code] [499] Initiate PC-Link (Local Downloading) (Section 5.
PAGE 42
Contact ID A P P E N D I X A The Partition ID Codes must be 4 digits. All reporting codes must be 2 digits. The following is a list of Contact ID reporting codes. The first digit (in parentheses) will automatically be sent by the control. The last two digits are programmed to indicate specific information about the signal. For example, if zone 1 is an entry/exit point, the alarm reporting code could be programmed as [34].
PAGE 43
SIA Format A P P E N D I X B SIA Format Level 2 (Hardcoded) The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard January 1996. This format will send the Account Code along with its data transmission.
PAGE 44
Programming LCD Keypads A P P E N D I X C If you have an LCD5500Z Keypad, additional programming is required for proper operation. The following is a description of the available programming options and their accompanying programming sections: How to Enter LCD Programming Follow the programming procedure as outlined in Section 4 by pressing [✱] [8] [Installer’s Code]. Press the [✱] key. Enter the two digit Section number to be programmed.
PAGE 45
P R O G R A [61] Second User Display Mask Default Option OFF I_______I 1 I_______I 2 ON I_______I 3 ON I_______I 4 ON I_______I 5 OFF I_______I 6 ON I_______I 7-8 OFF M M M I N G L ON Installer Programming prompt ON Stay Arm prompt ON Quick Arm prompt ON Interior Arm prompt ON Quick Exit prompt ON View Event Buffer prompt ON For Future Use [65] [66] [97] [98] D K E Y P A D S OFF Installer Programming prompt OFF Stay Arm prompt OFF Quick Arm prompt OFF Interior Arm prompt OFF Quick
PAGE 46
NOTES: 46
PAGE 47
PC1555 Control Panel Wiring Diagram PC1555 CONTROL PANEL WIRING DIAGRAM Incorrect connections may result in fuse failure or improper operation. Inspect wiring and ensure connections are correct before applying power. Do not route any wiring over circuit boards. Maintain at least 1” (25.4mm) distance.
PAGE 48
1-800-387-3630 TM Security Products © 1997 Digital Security Controls Ltd. 1645 Flint Road, Downsview, Ontario, Canada M3J 2J6 Tel.
PAGE 49
• W A R N I N G • This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. Installation PC1555 Manual Software Version 2.0 (2-wire Smoke Option) DLS-1 v6.
PAGE 50
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. Industry Canada does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
PAGE 51
Table of Contents Limited Warranty ii Section 1: System Introduction 1 1.1 1.2 1.3 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 5.27 5.28 5.29 5.30 Specifications ...................................................................... 1 Additional Devices .............................................................. 2 Out of the Box ..................................................................... 2 Section 2: Getting Started 3 2.
PAGE 52
LIMITED WARRANTY WARNING Please Read Carefully Note to Installers Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.