Specifications

ManualsBrandsDSC ManualsComputer equipmentDigital Security Control PC158O

1.1 Specifications

Control Panel Specifications

Flexible Zone Configuration:

• Six fully programmable zones

• Seven Access Codes: five User, one Master and a

second Master code

• Normally Closed, Single EOL, Double EOL

• 21 Zone Types, 6 Programmable Zone Options

Audible Alarm Output:

• Supervised Bell Output (current limited at 3 amps), 12 V

• Steady or Pulsed Output

EEPROM Memory: Does not lose programming or

system status on complete AC and Battery failure

Programmable Outputs:

• Two Programmable Voltage Outputs, 22

programmable options

- One High Current (300 mA) PGM output on main

panel

- One Low Current (50 mA) PGM output on main

panel

Powerful 1 Amp Regulated Power Supply:

• 550 mA Auxiliary Supply, 12 V

• Positive Temperature Coefficient (PTC) components

replace fuses

• Supervision for loss of AC Power, Low Battery

• Internal Clock Locked to AC Power Frequency

Power Requirements:

• Transformer = 16.5 VAC, 40VA

• Battery = 12 volt 4 Ah minimum rechargeable sealed

lead acid

Remote Keypad Specifications:

• Three Different Keypads Available:

- PC5506 6 Zone LED Keypad

- LCD5500 Alphanumeric Keypad

- PC1575RK 6 Zone LED Keypad

• The PC5506 and LCD5500 keypads have 5 Fully

Programmable Function Keys

• Connect up to 8 Keypads

• Four Wire (Quad) Connection to KEYBUS

• Built in Piezoelectric Buzzer

System Introduction

SECTION1

Digital Communicator Specifications:

• Supports Major Formats including SIA and Contact ID

• Event Initiated Personal Paging

• Three Programmable Phone Numbers

• Two Account numbers

• Supports LINKS 1000 Cellular Communication

• DTMF and Pulse Dialing

• DPDT Line Seizure

• Anti-jam Feature

• Split Reporting of Selected Transmissions to Each

Telephone Number

System Supervision Features

The PC1580 continuously monitors a number of possible

trouble conditions including:

• AC Power Failure

• Trouble by Zone

• Tamper by Zone

• Fire Trouble

• Telephone Line Trouble

• Failure to Communicate

• Low Battery Condition

• Bell Output Trouble

• Module Fault (Supervisory or Tamper)

• Loss of Internal Clock

• AUX Power Supply Fault

False Alarm Prevention Features

• Audible Exit Delay

• Audible Exit Fault

• Communication Delay

• Urgency on Entry Delay

• Quick Exit

Additional Features

• Auto Arm at Specified Time

• Keypad Activated Alarm Output and Communicator

Test

• All modules connect to the system via a four wire

KEYBUS up to 1000' (305 m) from main panel

• Event Buffer can be printed using PC5400 RS232 Serial

Interface module

• Supports the ESCORT 5580 Voice Prompt Module with

Automation/Lighting Control

• An Event Buffer which records the past 100 events with

both the time and date at which they occured

• Uploading and Downloading capability

• Local Downloading capability with the use of the

PC-LINK Adaptor

Summary of content (44 pages)

PAGE 1
System Introduction S E C T I O N 1 Digital Communicator Specifications: • Supports Major Formats including SIA and Contact ID • Event Initiated Personal Paging • Three Programmable Phone Numbers • Two Account numbers • Supports LINKS 1000 Cellular Communication • DTMF and Pulse Dialing • DPDT Line Seizure • Anti-jam Feature • Split Reporting of Selected Transmissions to Each Telephone Number 1.
PAGE 2
S Y S T E M V I N T R O D U C T I O N 1.2.4 Downlook Video Transmission Module The Downlook Still-Frame Video Transmission Module (DLM1/DLM-4) is the ideal solution for all business and residential environments which require visual surveillance but where the presence of on-site security personnel is impossible, undesirable or unaffordable.
PAGE 3
Getting Started S E C T I O N 2 Step 10 Testing the System The panel must be thoroughly tested to ensure that all features and functions are operating as programmed. The following Sections provide a thorough description of how to wire and configure devices and zones. 2.1 Installation Steps The following steps are provided to assist you with installing the panel. We suggest that you read this section in its entirity before you begin.
PAGE 4
G E T T I N G S Programmable Outputs – PGM1 and PGM2 Each PGM output is designed so that when activated by the panel, the terminal will switch to ground. PGM2 can sink up to 50 mA of current to activate LEDs or a small buzzer. Connect the positive side of the LED or buzzer to AUX+, the negative side to PGM2. If more than 50 mA of current are required, a relay must be used. Please study PGM wiring in the accompanying diagram. PGM1 is a high current output which operates similar to PGM2.
PAGE 5
G E T T I N G S which slots are occupied in order to generate a fault when a supervisory is not present. How to Assign Keypads T A R T E D 2.8.1 Normally Closed (NC) Loops Each keypad must be assigned one at a time. After assigning all keypads, a supervisory reset should be performed. To assign a keypad to a slot, enter the following: 1. Enter Installer’s Programming. 2. Press [00] for Keypad Programming. 3. Press [0] for Slot Assignment. 4.
PAGE 6
G E T T I N G S 2.8.4 Fire Zone Wiring — Four-Wire Smoke Detectors All fire zones must be wired according to the following diagram: 2.8.5 Keyswitch Zone Wiring If PGM2 has been PGM2 programmed for keyswitch operation (momentary or maintained), the keyswitches must be wired according to this diagram: T A R T E D 2.8.8 LINKS Answer When using the LINKS 1000 cellular communicator, PGM2 may be configured for LINKS Answer.
PAGE 7
Keypad Commands S E C T I O N 3 bypass all Stay/Away type zones. The Bypass light will remain ON to inform the user that the interior protection has been automatically bypassed by the panel. If a delay zone is violated during the exit delay, the Stay/Away zones will be active after the exit delay expires. The user can add the Stay/Away zones back into the system at any time by entering the [✱] [1] keypad command (see section 3.4 “[✱] [1] Bypassing and Reactivating Stay/Away Zones”).
PAGE 8
K E Y P A D V C O M A N D S To view trouble conditions from an LED keypad: 1. Press [✱] [2]. 2. The keypad will flash the Trouble light. The zone indicator lights corresponding to the present trouble conditions will be ON. If the Code Required for Bypass option is enabled, only user codes with the Bypass attribute enabled will be able to bypass zones (see section 5.1 “Programming Security Codes”).
PAGE 9
K E Y P A D V C Trouble [4] – Zone Fault (including Fire Zone) This trouble will be generated if any zone on the system is experiencing trouble, meaning that a zone could not provide an alarm to the panel if required to do so. When a zone fault trouble condition occurs, the keypad(s) on the system will start to beep. Press [4] while in Trouble mode to view the affected zones. A Fire zone trouble will be generated and displayed in the armed state.
PAGE 10
K E Y P A D V C O M • [3] – Auto-Arm Time The system can be programmed to Auto-Arm at a certain time. When programming the auto-arming time, enter the time (hour and minute) using military format [HH MM]. For more information, see Section 3.3 – “Auto-Arming”. • [4] – System Test When [4] is pressed the panel will test the bell output, keypad lights and the communicator for two seconds. The panel will also send a System Test Reporting code, if programmed (see Section 5.
PAGE 11
K E Y P A D V C described below. A function is activated by pressing and holding the appropriate key for two seconds. “Stay” – Stay Arm Pressing this key will arm the system in the Stay mode, meaning that all Stay/Away type zones will be automatically bypassed. Delay type zones will provide entry and exit delay. The Quick Arm feature must be enabled in order for this key to function (programming section [10], option [6]). “Away” – Away Arm Pressing this key will arm the system in the Away mode.
PAGE 12
How to Program S E C T I O N 4 4.2 Programming Decimal Data The following section of the manual describes the Installer’s Programming function and how to program the various sections. A set number of programming boxes are allotted for each section requiring decimal data (e.g.: codes, telephone numbers). If a digit is entered for each program box, the panel will automatically exit from the selected programming section. The Ready light will turn OFF and the Armed light will turn ON.
PAGE 13
H O W V T O V P light will turn OFF and the Armed light will turn ON. Refer to Section 5 in this manual to determine what each option represents and whether the light should be ON or OFF for your application. R O G R A M Press any of the Emergency Keys (Fire, Auxiliary or Panic) to advance to the next digit.
PAGE 14
Program Descriptions S E C T I O N 5 [03] Instant Zone This zone type will cause an instant alarm if it is violated when the panel is armed. Typically, this zone is used for windows, patio doors or other perimeter zones. [04] Interior Zone This zone will not cause an alarm if violated during the entry delay. If the zone is violated before the entry delay has begun, it will cause an instant alarm. Typically, this zone is used for interior protection devices, such as motion detectors.
PAGE 15
P R O G R A M D E S [09] 24 Hour Supervisory Zone (with LINKS) If this zone is violated when the system is either armed or disarmed, the panel will report to the central station and will log the zone fault to the Event Buffer. C R I P T I O N S • Downlook Activation Option (Video) – If enabled, this attribute will activate the DLM-1/DLM-4 Downlook module. When a given zone goes into alarm, it will activate the DLM to take a picture of that zone.
PAGE 16
P R O G R A M D E S C R I P T I O N S alarm whether the panel is armed or disarmed and report to the central station. All other types of zones will only go into alarm if the panel is armed. The Police Code reporting code will be sent after 2 zones have gone into alarm within the same armed period. 5.5 Communicator – Account Numbers The account number is used by the central station to distinguish between panels. There are two account numbers programmable for the PC1580.
PAGE 17
P R O G R A M D E S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ R I P T I O N S The Auxiliary Power Supply Trouble Alarm Reporting Code will be transmitted if the AUX output is shorted out. The AUX output of the control panel incorporates a fuseless design. When excessive current is drawn, the panel will automatically shut off the output.
PAGE 18
P R O G R A M D E S C R I P T I O N S Additional Notes on Contact ID 1. Account numbers must be four digits. 2. All Reporting Codes must be two digits. 3. Substitute the HEX digit ‘A’ for the ‘0’. 4. To prevent the panel from reporting an event, the Reporting Code should be programmed as [00] or [FF]. Please refer to Appendix A for a list of Contact ID Identifiers. 5.8.
PAGE 19
P R O G R A M D E S key (Hex [C]). The panel has no way of confirming if the pager was called successfully; a Failure To Communicate trouble will thus never be generated. C R I P T I O N S Downloading can also be performed through the LINKS 1000 cellular communicator if the phone line is disconnected. If Call Back is being used, you may have to program the LINKS 1000 Preamble to have the panel call the computer correctly.
PAGE 20
P R O G R A M D E S The PGM will activate when any of the following events occur and will remain active for as long as the keypad buzzer is active: • Door Chime • Entry Delay • Auto-Arm Prealert • Audible Exit Delay • 24 Hour Supervisory Buzzer Zone [06] System Armed Status When the system is armed, the PGM output will switch to ground at the beginning of the exit delay. The output goes high (open) when the panel is disarmed.
PAGE 21
P R O G R A M D E S I P T I O N S Bell Circuit Trouble Reporting Code ..................... Section [43] Bell Circuit Trouble Restoral Reporting Code ....... Section [44] ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ [29] Audible 24 Hour (PGM2 only) A Panic button may be placed on the PGM2 Terminal for use as an Audible 24 Hour Panic.
PAGE 22
P R O G R A M D E S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ [F] Key Enable ..................................... Section [08], Option [3] [P] Key Audible Bell and Buzzer ......... Section [08], Option [4] ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Arming / Disarming Options If the Quick Arm option is enabled, the panel can be armed without a user code by entering [✱] [0] or by pressing the Stay or Away key on the LCD5500 or PC5506 keypads.
PAGE 23
P R O G R A M D E S ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 5.23 Swinger Shutdown ................................................ Section [62] Event Buffer The panel will store the last 100 events which occurred on the system. The Event Buffer will contain the name, time and date of each event, along with the zone number, user code number or any other information pertaining to the event.
PAGE 24
P R O G R A M D E S • if unsuccessful, the panel will try to call using the land lines • if unsuccessful, the panel will try to call using the LINKS This process will continue until the panel has successfully communicated with the central station or the Maximum Dialing Attempts has been reached. C 5.27 P T I O N S Resetting Factory Defaults On occasion, it may be necessary to default the control panel or one of the connected modules: the ESCORT5580 module and the PC5400 Printer module.
PAGE 25
Programming Worksheets F O R T H E R E C O R D For the Record Customer: _______________________________________________________________________________________ Address: ________________________________________________________________________________________ _______________________________________________________________________________________________ Phone: __________________________________________ Installation Date: _____________________________________ Installer’s Code: __________________
PAGE 26
Keypad Programming P R O G R A M M I N G W O R K S H E E T S [00] Keypad Assignment (Section 2.5 “Keypad Assignment”) Note:: This must be done at each keypad requiring programming.
PAGE 27
P R O G R A M M I N G W O R K S H E E T [03] Installer’s Code (Section 4 “How to Program”) Default 1575 Default I_______I_______I_______I_______I or 157500 I_______I_______I_______I_______I______I_______I [04] Master Code (Section 5.1 “Programming Security Codes”) Default 1234 Default I_______I_______I_______I_______I or 123400 I_______I_______I_______I_______I______I_______I [05] Second Master Code (Section 5.
PAGE 28
P R O G R A M M I N G W O R K S H E E T [10] Third System Option Code Default OFF OFF OFF OFF ON ON I________I I________I I________I I________I I________I I________I Option 1 2 3 4 5 6 ON Arm / Disarm Bell Squawk Enabled Bell Squawk During Auto Arm Bell Squawk On Exit Delay Bell Squawk On Entry Delay Audible Exit With Urgency Quick Arm Enabled OFF Arm / Disarm Bell Squawk Disabled No Bell Squawk During Auto Arm No Bell Squawk On Exit Delay No Bell Squawk On Entry Delay Silent Exit De
PAGE 29
Communicator Programming P R O G R A M M I N G W O R K S H E E T S NOTE:: For sections [31] to [46], the contents of every section by default is [F]. [31] First Telephone Number (32 Digits) (Section 5.6 “Communicator – Phone Numbers”) I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I [32] Second Telephone Number (32 Digits) (Section 5.
PAGE 30
P R O G R A M M I N G W O R K S H E E T [42] Opening (Disarming) Reporting Codes, Access Codes 1-6 (Section 5.
PAGE 31
P R O G R A M M I N G W O R K S H E E T [53] Openings & Closings Communicator Call Directions (Section 5.4 “Communicator – Dialing”) Default ON OFF OFF OFF Option 1 2 3 4 I________I I________I I________I I________I ON 1st Telephone Number 2nd Telephone Number 1st Telephone Number (via LINKS) 2nd Telephone Number (via LINKS) OFF Disabled Disabled Disabled Disabled [54] System Maintenance Alarms & Restorals Communicator Call Directions (Section 5.
PAGE 32
P R O G R A M M I N G W O R K S H E E T [68] LINKS 1000 Preamble (Second Telephone Number) (Section 5.24 “LINKS 1000 Cellular Communicator”) Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F) [69] LINKS 1000 Preamble (Third Telephone Number) (Section 5.
PAGE 33
P R O G R A M M I N G W O R K S H E E [82] Second International Options Code Default OFF ON OFF OFF OFF OFF I_______I I_______I I_______I I_______I I_______I I_______I Option 1 2 3 4 5 6 ON European Dialing Parameters Force Dialing Enabled Test Transmission interval in Minutes 1600 Hz Handshake Answer Acknowledge Enabled (ID Tone) 2100 HZ ID Tone OFF North American Dialing Parameters Force Dialing Disabled Test Transmission Interval in Days Standard Handshake Disabled 1300 Hz ID Tone
PAGE 34
Appendix A C O N T A C T I D Contact ID The Partition ID Codes must be 4 digits. All reporting codes must be 2 digits. The following is a list of Contact ID reporting codes. The first digit (in parentheses) will automatically be sent by the control panel. The last two digits are programmed to indicate specific information about the signal. For example, if zone 1 is an entry/exit point, the alarm reporting code could be programmed as [34].
PAGE 35
Appendix B S I A V F O R M A T SIA Format Level 2 (Hardcoded) The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard - February 1993. This format will send the Account Code along with its data transmission.
PAGE 36
Appendix C P R O G R A M M I N G V L C D V K E Y P A D S Programming LCD Keypads If you have an LCD5500 Keypad, additional programming is required for proper operation. The following is a description of the available programming options and their accompanying programming sections: How to Enter LCD Programming Follow the programming procedure as outlined in Section 4 by pressing [✱] [8] [Installer’s Code]. Press the [✱] key. Enter the two digit Section number to be programmed.
PAGE 37
[62] Third User Display Mask Default Option I_______I 1 ON I_______I 2 ON I_______I 3 ON I_______I 4 ON I_______I 5 ON ON I_______I 6 I_______I 7 ON I_______I 8 ON ON System Test prompt ON Time and Date prompt ON Auto-Arm Control prompt ON Auto-Arm Time prompt ON Download Enable prompt ON Bright Control prompt ON Contrast Control prompt ON Buzzer Control prompt ON OFF System Test prompt OFF Time and Date prompt OFF Auto-Arm Control promptOFF Auto-Arm Time prompt OFF Download Enable prompt OFF Bright Contr
PAGE 38
LIMITED WARRANTY Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.
PAGE 39
Control Panel Wiring Diagram ✁ PC1580 CONTROL PANEL WIRING DIAGRAM Incorrect connections may result in fuse failure or improper operation. Inspect wiring and ensure connections are correct before applying power. Do not route any wiring over circuit boards. Maintain at least 1” (25.4mm) distance.
PAGE 41
Installation Manual PC158O Software Version 1.O DLS-1 V6.1 and up • W A R N I N G • This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.
PAGE 42
FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 43
NOTICE! You must read this entire manual, including all notices and warnings, in order to install this system so that it is fully functional. WARNING! This entire system must be completely tested on a regular basis to verify the operation of all system functions, in accordance with the recommendations of the security systems industry.
PAGE 44
T 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 5.24 5.25 5.26 5.27 5.28 A B L E V O F Arming / Disarming Options .......................................... 22 Entry / Exit Delay Options ............................................. 22 Transmission Delay ....................................................... 22 Swinger Shutdown ........................................................ 22 Event Buffer ................................................................... 23 Keypad Lockout .............