Use and Care Manual

DRYLOK® Concrete Protector
®®
UNITED GILSONITE LABORATORIES
MAILING: P.O. Box 70, Scranton, Pennsylvania, 18501
SHIPPING: 1396 Jefferson Avenue, Dunmore, Pennsylvania, 18509
T
OLL FREE: 1-800-UGL-LABS (845-5227)
P
HONE: 1-570-344-1202 • FAX: [phone]
www.ugl.com
D R Y L O K ® M A S O N R Y P R O D U C T S
DRYLOK Latex Base Concrete Protector
provides clear weatherproof protection
against deterioration caused by de-icing salt,
gasoline, oil, weathering and efflorescence
(white, powdery, salt-like deposits visible on
masonry). DRYLOK’S unique SALTLOK®
Technology penetrates into the surface
providing superior resistance to unsightly
efflorescence staining oen visible on brick,
block and poured concrete surfaces.
DRYLOK Concrete Protector seals bare
masonry surfaces against dusting, staining,
surface cracking and pock marking.
Protects against road salt, weathering,
gasoline and oil
Prevents excessive dusting, surface cracking
and pock marking
Solidifies masonry surfaces for top coat
Minimizes reoccurring efflorescence
Primes prior to paint
SEALER: Ideal for interior, exterior,
horizontal or vertical masonry surfaces,
including concrete driveways, garage oors,
basement oors, concrete sidewalks, block
retaining walls, brick siding/walkways,
terrazzo, and slate surfaces.
Worn surfaces with similar clear coatings,
which allow water penetration, may be
recoated with DRYLOK Concrete Protector.
For best results test for proper adhesion on a
small area prior to coating entire surface.
PRIMER-SEALER: DRYLOK Concrete
Protector can be used as a primer/sealer
prior to applying DRYLOK Latex Base
Concrete Floor Paint, DRYLOK E1 1-Part
Epoxy Floor Paint, latex, alkyd or
polyurethane concrete oor paints or
carpeting. For self-adhesive oor tiles, check
with tile manufacturer for adhesion
compatibility.
MINIMIZE RECURRING EFFLORESCENCE:
DRYLOK Concrete Protector can be used as
a primer/sealer under DRYLOK Masonry
Waterproofer or other masonry wall
coatings to minimize recurring efflorescence.
When applied over powdery surfaces such
as chalking masonry paint, sand blasted
masonry and powdering concrete and
mortar DRYLOK Concrete Protector
solidies surface for painting.
DRYLOK Concrete Protector is not for use
over silicone treated surfaces, or on any
masonry surface subjected to hydrostatic
pressure. Surfaces subjected to hydrostatic
pressure should be treated with DRYLOK®
Masonry Waterproofer.
Not for use on asphalt surfaces.
COMPOSITION:
Latex base
SHEEN:
Ma nish
% WEIGHT SOLIDS:
19-21%
% VOLUME SOLIDS:
18-20%
DENSITY (LBS./US GAL.):
8.5
VISCOSITY:
10-12 seconds Ford #4 Cup @ 77ºF
pH:
8.5-9.5
COLORS:
N/A
DRY TIME:
• To touch: 1 hour
• To recoat: 6 hours
• Heavy traffic: 24 hours
• Rain free: 24 hours
Note: Drying time may be affected by
temperature, humidity and lm
thickness.
CLEAN UP:
Soap and water
Dispose of contaminated absorbent,
container and unused contents in
accordance with local, state and federal
regulations.
COVERAGE (SQ. FT./US GAL.):
• 400 sq. ./gal.
Note: Actual coverage will vary
depending upon application method,
surface texture and porosity.
RECOMMENDED FILM THICKNESS/COAT:
• 5 wet mils/coat
FLASH POINT:
>212ºF
SHELF LIFE:
5 Years
FREEZE/THAW:
Keep from freezing.
CONTAINER SIZES:
One quart (US), one gallon (US) and
ve gallon (US) containers
Does not exceed 100 g/L
N/A
O V E R
S
o
a
p
DRY TIME:
1 Hour
Recoat 6 Hours
CLEAN-UP:
Soap and Water
COVERAGE:
1-2 Coats
SPREAD RATE:
400 Sq. Ft./Gallon